Trossen Robotics PhantomX Mark II First Phoenix code test

Рет қаралды 19,791

9 жыл бұрын

Trying out different gaits on a new PhantomX with Dynamixel AX18 servo's. Blew a cell in the original 2200mah LiPo in about half an hour after the build, so I stuck a Yellow RC 4000mah LiPo on the top (hence the ugly Traxxas power connector). www.magicbullet.nl

Пікірлер: 21

@IamUke 7 жыл бұрын

That was beautiful cat at 0:55. And the hex is pretty cool too. Thanks for sharing.

@stephanieallen6485 3 жыл бұрын

Cat: the hell is that thing? I'm out. My humans are crazy.

@manoi2010 Жыл бұрын

hello I have a hexapod like yours but I don't know which keys to push to use it .... Could you make a video where when you use it I can see your controller so I can see which keys you use to control the hexapod...... please if you can help me just a short video where I can see the keys you push !!!!! please help me...... I await your reply. Thanks. Have a good day

@cristianecosta4334 4 жыл бұрын

A audácia do gato é fabulosa,e o projeto é colossal .#magnifico Nota : 20 (100)

@manoi2010 Жыл бұрын

please help me don't you remember any key not even the one to change walk or any key you remember? don't you know anyone who can have all the commands? Thank you have a nice day

@rmigofun 3 жыл бұрын

Nice spider!

@magnuswootton6181 3 жыл бұрын

I think a murky green colour would suit one of these.

@carloscarvalho4595 5 жыл бұрын

Hello, do you have the code to donwload? I have all the parts printed on my 3d printer but i try a few months to install the phoenix code but all time i fail. Thank you

@vwcreativetechnology 5 жыл бұрын

what fails? are you using the arbotix board?

@carloscarvalho4595 5 жыл бұрын

@@vwcreativetechnology no, only arduino board. I search a lot and maybe i need the arbotix board

@vwcreativetechnology 5 жыл бұрын

Look for the Lynxmotion Phoenix code, not for the Trossen hexapod. Also before you do anything with Phoenix, first make sure ROS is working first. Phoenix is just advanced gaits and motion...don't use it for initial build tests.

@herlonmartins8747 3 жыл бұрын

@@carloscarvalho4595 hello how are you doing? I read these comments you made here, I was wondering if you managed to do this project, if you got the linxmotion code, I know it's been a long time, if you did you could send me this code, also the parts to print on the 3d printer, my email herlon.martins12@hotmail.com, I really like these projects, thank you.

@carloscarvalho4595 3 жыл бұрын

@@herlonmartins8747 hello, i'm fine and you? yes the project it's done. Next days will sent to you the full code and the stl parts that i print in my project. Only need to search but will sent to you. :)

@manoi2010 Жыл бұрын

hello congratulations for the video !!!! I bought a Mark 3 hexapod like yours but the seller doesn't remember anything about how to use it ... since you made a fantastic video could you help me? in the hexapod there is phoenix code and I control it with xbee Commander 2 could you tell me the names of the keys and what function they have? please help me wait for an answer thank you good day

@vwcreativetechnology Жыл бұрын

Hi, I don't know sorry, I ditched the xbee commander long ago and used my own existing communication protocol with different transmitters. I think you are looking for the button to change gaits right?

@manoi2010 Жыл бұрын

@@vwcreativetechnology no i don't know anything......help you don't remember all button function?in the video you use xbee commander 2.....