6 years ago, but man I wish i searched this first. I spent an hour troubleshooting, only to have to click the switches.... Thank you! Worked on handicare with error codes 3 and 6.(in case someone with model is having issues)
@meltsnerrita3 жыл бұрын
Thank you very much ! You very helped me .
@adammurdin83484 жыл бұрын
hi, we have a second hand one of these we are trying to install. going up seems fine but will not go down. when you try to go down the charging dash just flashes on and off, any ideas? thanks
@ingedijk13023 жыл бұрын
Hey Carlos can you show a video of replacing the batteries and connecting all the electrical fittings from the on/off switch. Can't seem to locate a wiring diagram
@watchmy6663 жыл бұрын
did you find where the batteries go?
@drelanthony Жыл бұрын
, ww1w, as
@kvtkvt413 ай бұрын
Hi, can you advice how/where to look as my stairlift has no power at all even though the power supply shows green but nothing on the display just above the on/off switch. Thank you
@terrencewilliams32663 жыл бұрын
How do I change the batteries in this style lift ?
@mustafanaik58662 жыл бұрын
Hi there I was wondering what to do with a code "l-" with 2 dots . . Under. It says in the manual to reset the stairlift but not working
@shastflamearashi64283 жыл бұрын
Got a error code #0. At the top we press down. So the chair starts swiveling in line with staircase but, we stopped it too soon so its at a 45 degree angle. When pressing down again it no longer swivels and starts traveling. Confused we stopped now it just says error 0. Any help? Handicare 950+
@leejohnson46642 жыл бұрын
My stairlift won’t go all the way to the top, how do i fix It I had it put in more pieces after buying it from another person in order to make it reach my top stair the person I bought it from stairs ended earlier then mine so it stops where his stairs ended and it won’t go up any higher do I need to reprogram it to make it reach the top or make it go up farther nothing is blocking it to move higher
@martind5865 жыл бұрын
have you ever taken the cover off? ( the cover that surrounds the on off switch. I need help knowing where the cords go from the on off switch area to circuit board...I cant find pictures or diagrams ANYWHERE. please help, thanks,,,
@terrencewilliams32663 жыл бұрын
I'm in that same boat .. trying to change the batteries a friend took it apart to order new batteries and now cant remember how to put it all back
@martind5863 жыл бұрын
@@terrencewilliams3266 damn--i took pictures when i figured it out --good luck thou
@eoinwalsh701723 күн бұрын
Hi there my friend has this lift and it starts off normal but then runs real slow.Is there any fix for this thanks
@sheilabellows9791 Жыл бұрын
What does it mean when there aren't any numbers showing on the stairlift
@amjadmohammed55872 жыл бұрын
Hi carlos. I bought a second hand. Handicare 950. It works but the remote is not. Changed the battery on both remote. It light up but nothing happens. It there a fix eg: reprogram ete. Thanks Aj
@bobjones83782 жыл бұрын
Press the small button located on top of the main control board and hit down on the remote while holding the programming button when the led on the main control board turns green it's programmed.
@suzannejane85473 жыл бұрын
How do I do my stairslift manually
@carolbeech3849 Жыл бұрын
Hi our stair lift number 2 is this just charging please advice
@Angela-jl1lh4 жыл бұрын
Have a Stannah 600. Just a year after install. Gets to top has a 9. Have had service out twice to move it manually a little b4 top. But I have forgotten. To stop now it's stuck at top. With a 9. Any help or advice greatly apprrciatef
@Angela-jl1lh4 жыл бұрын
Appreciated
@aidabab3 жыл бұрын
Hi , I’ve got the same model 600 and the same problem as you Its stuck at the top of the stairs on number 9 I found a quick fix to move it , there is a removable cover over the display That hides three buttons , two are push buttons and one is a SWITCH !!! Press the switch then one of the buttons to move it It will move very slowly , I’m going to try and fix mine tomorrow As I do electronics , please remember to put the SWITCH back under the panel to where it was If you get it sorted , hope this helps for now :-)
@ripleypd452 ай бұрын
Whats the chances that you would have a cam limit Switch for a SL-1000
@charliesusan22863 жыл бұрын
Hi how to manually winding the stairlift when the lift has got.no power? Also when doing manual winding how to remove the break? I can't wind it because i believe some break is engaged. Thanks
@LindellCooper10 ай бұрын
Have a acorn 130 and I have a 5in light 8 on the way up and a 9 on the way down
@LindellCooper10 ай бұрын
U Charlie doesn't move that it likes 38 or 39
@LindellCooper10 ай бұрын
Flash season 3 and 8 on going to try to go up in the three and a 9-minute try to go down
@1mc401 Жыл бұрын
What does an "n" mean?😰
@ckpatel88854 жыл бұрын
hi there - I am getting #8 & #9 - i have pressed all the things you had described
@LindellCooper11 ай бұрын
What does this mean
@LindellCooper11 ай бұрын
Eight starts up and stops + 9
@LindellCooper11 ай бұрын
What else do I need to check
@LindellCooper7 ай бұрын
My charging light is flashing a lot of letter letter u
@brinozke5 жыл бұрын
i didn't turn on my in a long time now it doesn't move at all and number 8 is flashing. Can you give me some help to try to fix it myself. Thanks
@CarlosLopez-ck5oz5 жыл бұрын
brinozke what is it showing when you try to go up or down? The most common issue is a code 0.
@brinozke5 жыл бұрын
Carlos Lopez the chair is up and can’t really be sure but it looks more like a 8 just number no letter. I’m taking a look again and it may be cero too I just see the whole panel flashing without stoping unless I turn it off. The chair doesn’t move at all. If is cero what will be your diagnostic? Or recommendation. Thanks
@CarlosLopez-ck5oz5 жыл бұрын
brinozke a zero is usually a key that is turned off, or the stairlift went too far to the top and overran the limit switch. In which case you either turn the key on, or use a winding tool to bring it down a foot. A number 2 means it isn’t charging, and a 6 or a 4 is related to a safety edge.
@Zeljk0805 жыл бұрын
@@CarlosLopez-ck5oz I installed new batteries. shows 8-9-n half speed
@SuperGuitarlos5 жыл бұрын
Željko 8 is going uphill, 9 is coming down. n is definitely half speed which means the batteries are at a critical level and aren’t able to continue receiving a charge. You may need to replace those batteries. If you charging system is working (check all connections in bottom of track to make sure they are tight - also make sure copper strip is clean and charger is plugged in) it may have something to do with the charging circuit on the board.