Wonderful job thank you so much

That feeling you get when you hit power and it lights up. If you know, you know.

I could use your help. I am not a tech just a DIYer. I have a Kenmore 90 Series washer. After completing one load of wash I started a second. The tub filled with water, agitated then stopped. No matter what setting I put it in nothing happens. No humming, nothing. Another Kenmore 90 series washer was given to me. It agitated but no spin. After checking it out it was only a loose wire. Plugged it in & it went through the cycles. Put a load of cloths in & the only cycle that will now work is the spin. Any help on either one of these would be appreciated. I did notice same series but different timer control model. I did check the lid switch, both are good. I even jumped them to make sure. On the first one I changed the timer & the only function is the water will fill.

Thank you for making that video.

This is my exact machina. Mine stopped filling with water?? Can you please help

AH! This is close to my model, but I lack the Spin Speed button which I hear you can hold down for 5 second 3x to test the cycles without the lid lock. Mine turns on just fine, but I keep getting the LF error code for Low Flow, or Long Flow. Took the hoses off, cleaned out some sand from the screen (we are on a well, and this was bought in late 2006). It keeps stopping mid-cycle, especially during the Rinse cycle. I have to hit Start to bypass the LF code but I might do that 10x before it actually works and proceeds forward in the cycle. You can hear it try to fill but it takes many tries before it moves on to Spin and Drain. Only the Cold water screen had sand; the hot seemed just fine. Trying to run the washer only on hot water wash/rinse didn't bypass the problem. About to call a repair man, but I hesitate to pump a few. hundred dollars into machines this old yet I agree with all your comments about sustainability. Would hate to see these go to a landfill, and it matches my dryer which works perfectly. Would hate to buy a whole new set. Any ideas? Thanks!

I have a kenmore 100 series. For months it will stop and keep lid locked during the cycle. It can stay like that for hours. What I do is unplug the bone. It takes hours before the machine unlocks the lid

Thank you for this informative video. What voltage multimeter would you recommend for a beginner to get?

Great video! Is it worth keeping that old board for the components that aren't bad?

How much did you flip it for?

When I pull my knob(power on), I hear a "buzzing" , so I assume its getting power. Can the board still be bad or should I look for something else????

My Kenmore washer wasn't powering on and I saw one possible solution was unplug it for about 5 minutes and then replug it in and I left it unplugged about 10 minutes plugged it back in and it worked fine. I also turned off and turn back on the circuit breaker but it wasn't off in first place so i think the real fix was just unplugging and replulgging. I read this resets it .

Very good video thank you!! My washer has f 70 code , what I need to do ??

I have a Kenmore 600 series (mod # 110.26132410) top load washing machine. When putting in a new load of clothes, it just won't turn on. I definitely have power going into the main control (tested that) any other suggestions? Thank you. Great video.

I have a kenmore washing machine, a 500 series. The machine doesn’t start, it has all the lights off but it’s rinsing out the water, if that made any sense. How do I fix it?

I have the exact same washing machine and mine will not spin, it turns on and makes the noise in everything but it won't spin. What could that be I also went ahead and hit subscribe for you

I have a similar model 110.27082601 Can you tell me where I can find the circuit board you mention for a reasonable price?

Im trying to justify fixing my Kenmore washer from about 2012. Its a smaller one in the $550 range. Im pretty handy and mechanical i do my own auto work but i feel like mine has everything wrong with it😂😂 evwntually it would wouldnt agitate (impeller) it was like that for quite awhile. Then it stopped spin drying. Then shortly after that (yes, I used it twice after it wouldnt spin dry and quickly handwashed inside washer 😂) it drained and stopped doing anything at all. The door has a latch and a lock. If i play with that i can get it to turn on but thats it. Nothing else. Just says "sensing". When it was somewhat working there where times id smell an electrical smell though very faint. Checled the board and nothing visible thats obvious. It would be a shame to toss out if it was something easy like this but I feel its more than that for some reason

I plugged in my Kenmore washing machine & didn't know the knob was already powered on when I plugged it into the wall & it made an electric sound, then stopped working completely, blew a fuse or what??

Great info THanks

I need 2 buy that high voltage tool so I can pinpoint where it needs fuse, right?..., that tool is to cut corners n exactly know what's old, for a newer part.

I have a 110 that will light up like its going to start, but then just starts clicking from under the tub?

May be you know the problem why my LG front load when first turn on it just spin no water come out and have to use garden hose to keep spray water where soup and where come out on top of machine for 30 seconds or so then the water come out by itself then I can stop spray water.

What is the problem when the washer won't start, but when you unplug and plug in again it works again for another few days

Hello, my washer is stuck on express load have unplugged for several minutes/overnight but goes back to express load will not shut off unless I unplug No error code. Model # 110-22062 109 Type 170 😢

Mine filled up with water, now won't turn on, I hear a buzzing when I pop the knob up.

Hey I have a kennmore elite 2015 or 2016 model with the glass top I turn the knob and the selection doesn’t change any ideas?

Please tell me hoe to check the control board!

washer will fill with water and drain and spin but won’t go into “wash cycle” ?

Is there a error code for a bad board ?

I want to see change out the clutch

I will take it. My board must be fried also.

Won't drain the water

Kenmore dryer light stopped working replaced bulb still not lighting up help me

thanks! what is the IC part#, any way to see it?

My kenmore washer is showing f21

Will only fill 1/3 of the water

I need ur HELP PLEASE!!!!

Mine just died like this and same model

Bro u paid NOTHING for the washer lol what’s it gonna hurt for it to sit around for 6 weeks??? 😂😂

I’ll subscribe just to see him, lol. Jk!!!

I have one identical to it the problem is everything else works but the pump won’t turn on I pulled it off and hooked power to it and it works nothing is plugged up. Anyone got any suggestions?

Go packers