vizio ,,trash from China ...do i need to say anything more

I just want to say I love your videos and appreciate your time making them. It may not look like it from my channel but I actually do a lot of similar stuff of camera and your insight is great, so well done :) Steve

Thanks for posting the video, very helpful! I have a vizio vo320e that I believe is the tcon/mainboard but not 100% sure...No video with sound and the backlight is working...Remote does control the volume/channels like normal so I'm not sure if this model has the tcon built into the mainboard or separate. Thought you may have some insight on this model?

I watched your video and liked how informative it is. I have an issue with my lg led tv the ribbons are good and the t con board is good but on the bottom right hand side it apears the the inside ribbon attached to the screen is over heating? Wouls this mean a bad screen?

Thanks, actually can you swap them at the T-Con/Main board?

Hey man i really like all your videos you have helped with serveral tvs. I picked up this exact same tv for free. I watched entire video. What make you think that it isnt the main board not sending the right signals and voltages to lcd panel just curious?

I had the same issue on Vizio m50-c1 half of the screen comes up fine with one side TCON connected to the lcd panel.. when both connected, I get blank screen. tested out all caps short .. i even changed all caps... short coming from glass lcd side ... Thanks for sharing ...

It might have worked to swap the cables, but in my experience, usually the ribbon cables have different pin counts. For example, the other might be a 41 pin cable and the other one a 51 pin cable. I've seen many LVDS-cable problems in LG-panels and most of the time you can see the defect with a magnifying glass, as the cable has not made proper contact with the connector. You can see imprints between the actual contacts in the cable, indicating a bad alignment of the cable in the connector

Norcal, I have a Samsung UN46D6420 that started with horizontal lines and progress to a black screen. I do have audio and back light. I took it apart and found that if I disconnect the Left side on the T-con I get half of the display to come up. The same is not true with the Right side it stays black. I notice that you mention on this video it was the panel vs the motherboard/t-con. What lead you to believe it was the panel vs the right channel on the board if that makes sense.

this is exactly whats going on with mine! thank you

Hi Norcal,. I have a Vizio E550i-AO. With the back cover removed, it looks very similar to the set you worked on. The symptoms I have are a good image shows but the lower half of the screen is in a darker shade. It's still visible but significantly darker. I removed the ribbon cables from the main board to the bonded boards at the bottom of the set. Half of the screen disappeared vertically when the ribbon cables were removed. When put back, the screen looks the same, darker at the bottom half. Do you have any recommendations? Thanks

For anyone who has a Vizio LED, LCD, or Plasma I seem to have a problem getting to the service menu to pop up... I held ch + & ch - at the same time while power is off for ten seconds, then try to attempt to push power button on, but the tv turns on by itself when I hold the channels buttons, anyway I continue to hold them for ten seconds then release any then hit menu but I don't see no "F" on bottom right for factory. I push and hold menu again with mute and exit/last buttons and still no service menu! Any help or ideas?

I have a vizio M601d-A3 and it has a horizontal line on the top left side thats black and runs 3/4 across the screen do you think its fixable ?

As always another very informative repair tips for lcd tv..thank you very much sir for yuor kind sharing.I got the right channel of subscription.

hi, so if my t-con board is good then when i unplug one of the ribbon cables half the screen should come on as in this viedo? and this means the panel it self is bad?

I have Vizio VW42LHDTV10A with a similar problem except the sections are separated as upper and lower parts of the screen. Could that also be a defective panel? When I got the TV the screen was black and the power button would not turn it off. I replaced the U33 and now have the blue screen with the "No Signal" moving around until it gets half way down the screen then it turns to white lines down the center vertically.

I assume you mean left side drives right side and right side drives left side. The pin outs are usually mirrored (reverse) of each other and since the ribbons only have conductors on one side you would need crossover cables. I suppose it could be done. Great question.

I am having a similar issue with my viziuhoh. it has a 1 inch part on the top that mimics what is playing on the bottom. cant figure it out

can i send u a video of what my vizio is doing for trouble shooting

I have the same Vizio. The interface board that holds the cold cathode tubes shorted and smoked on the top left tube. I ordered a used board. do you have any tips for a rookie on installing it ?

Hi I have exactly me the same defect on led tv Samsung, Have to repair you that this? Thanks

I have an RCA 42". I can turn the tv on and off, can hear sound, change the channels, and can see the backlight. But there isn't any picture. Can that be the Tcon board because I see no bad caps.

hi do you mean by something is loading the data down to the lcd panel that the boards are working correctly and all circuits are active up to a break in the wiring inside the panel and assuming there no connection defects found in the tabs or connections to and from the tcon [even with the use of freeze spray] ///not sure if this is my case,all tabs seem secure no change with freeze spray// ive got a 60 inch 2010 sony all bonding tabs [16] are on the bottom of tv and using [4] driver boards each pair from the tcon connected by flip up connectors using plastic circuit connectors that are similar to the flat ribbon connectors to the tcon in construction.These were crumpled during assembly resulting in cracks in both in the middle and looks as though a connection or 2 may be affected,however when i swapped sides with the worst one it didnt effect the right side of the screen with no picture problems,the issue with the left side is that i get a see thru mainly red vertical band [top to bottom]turns pink on lighter backgrounds,blue and hardly distinguishable with the logo screen,and is gone with black and on some scenes with bright lighting ie outdoor or price is right,otherwise depending on the background color of the video the red transparent bar will break up and become choppy otherwise it will be a solarized picture just between the bar [ie looks like a heat signature] also one side of the bar begins at the same point the screen turns white when disconnecting the left outer driver driver board [resulting in a quarter white screen] cant seem to find a closely comparable scenario,and was hoping that you or somebody may be able to advise between the likelihood of it either being a tcon/ panel/ or undetectable tab problem.//my thanks to all that took the time to read

you dont recommend either LCD or LED so whats left?? Plasma?? what do you own at home?? thank you sir

Very informative. I have a Vizio V555-H1 and I have the power led comes on then goes off. Backlight stays on I have checked those and they do all work fine. I have changed out the main board, power supply board, and tcon still no joy also swapped out the power cable & checked with the flashlight test and NO image. So any suggestions does it appear to be the lcd panel?

Hi Norcal, I have a Samsung pn50b450b1d white/gray transparent vertical lines in front of the picture. The picture quality is good; it's just that the transparent gray lines are in front of the picture. I changed the logic controller and had the same problem. What else could this be?

Would a bad T-CON board cause the screen not to come on period? I have an older Sony Bravia and if you repeatedly turn it on and off the picture will eventually come on and be beautiful. But if you cut it off and try to cut it back on, theres no picture or sound.

I a Sony Brieva. I have a black shadow in the middle of the screen. Could this be a tcon issue. ?

I have a Vizio D50X-D9. I pulled the panel to replace the backlights. It has some of those bonded tabs on each side of my screen, 5 per side i believe. The tabs appear to have a small metal piece in them. When I put my tv back together I had no screen. When I slide those side tabs back down into the side frame I got my picture back, but one side is dark and I have random horizontal lines going through my picture. Did I ruin it, or is there a technique that I need to know about putting those side tabs into place? I already used tape to secure them down. Any else that I can try? Thank you in advance.

I have a Sony bravia kdl 46w4100 old school and it has lines going up and down but on only hdmi I have salvaged a whole set of boards from a newer TV can I swap them out

Howdy. Just been given a JVC LCD LT42DG1. Starts with clear picture then within 10 secs has green vertical lines with distorted picture. Tried HDMI with same result, tried no signal at all, lasted probably 3 min with blue screen and "No Signal" before lines appeared again. Full screen, in groups of 3, pink/orange lines with blue screen. Any help, much appreciated.

Hello Sir, I mostly repair CRT based TVs here. Most customers use Sony, Panasonic,LG,ect. How can I get Repair Tips for similar make like these. Please help me.

I have 3years old SAMSUNG mod.no. VA 32H5500. On turning on my TV it works normal for few minutes and after that slightly flickering of screen starts with double image and subsequently vertical faded lines as well as horizontal lines appears with smoky pictures.What would be the proable cause & its solution.

I have a E421va when i look inside i dont see a T-con board I see a PC Board Unit Motherboard. I have no video, no sound, yes i have a backlight. Should i replace the pc board?

lg 47lb5900 has thin black horizontal lines spaced approximately .25 inches apart from top to bottom. the lines are visible but faded near the center of the screen. any thoughts?

I've got a Polaroid flm 2601 LCD tv. Video works on all inputs except in RF tuner mode. The raster is there but just snow. No audio in the RF mode and no headphone function. Also it will not channel up and seems stuck in channel 5 also with snow. Any suggestions? Thanks!

Sir I have an lcd 42" newly bought... But I Used it only 3 and a half months only......... The screen went black... After Some test I made... I figure out that the Audio is Ok... And There are Image too (tested via flash light)... I think now that the problem may be the back-lights Invertors... But I just cant situate the invertors yet and how to Fix My Hitachi 42"... How does it look like and how to fix it myself... Plz help... Thank You In Advance... I can Notice the same type of Power Supply Board as in your video... Are Those Two Identical Item The Invertors For Backlight...??? They Are Same And Exact Placement On Mine Too.......!!!

What would happen if you swapped the two ribbons to the lcd?.

How do you make difference if its t con. Board or lcd panel?

Thank you for your video and the time you put in to it. need help w/my Vizio model E701i-A3E, have sound, back lights and a lead screen but no picture. would you think I need to change the T-con board? a technician told me the screen has a shortcut but he sound like not telling all the truth. Anny help will be much appreciated.

I have a similar issue have sound but no video hope you okay thanks

Added in New T Con board to my Sony TV start-up distorted and then comes better picture most of the time when I turn the TV on distorted picture comes on first and then started to show good what should I do change the mainboard Powerboard!

I seen the electric screwdriver on your work bench. Wanted to buy one, would you recomend the one you use. what is are the specs. is it handy for Electronics and Light electrical works.

I have a 52" samsung tv. LCD. ln52a650a1fxza. Whenever I play HD channels my tv turns off and on and pixelates. I have to unplug to stop it. Non HD channels the TV works fine. How to fix?

Hello. I have a 50 in LG . I would like to know the name of the long thin board not the mother board the square one. but the one that runs parallel vertically . your help Most appreciated thanx

How are you? Thanks for your good and informative videos. My Samsung LED TV is showing vertical lines at the bottom of the screen but these lines would disappear and reappear after some time. What could be the problem.

If you don't recommend Led or LCD than what do you recommend I buy?

I recently put new led arrays into my tv they now all light but still no image on the panel. I then replaced all the boards in my LG 42LN575V Smart tv but screen still shows no image. You mentioned that if panel has gone you can sometimes write on the panel with finger tip which I tried & I get a white trace on screen which then fades does this suggest panel is at fault even though no damage is present to the eye. Thanks in advance for any help.

i have a 46" samsung LCD that appears to have a solarization issue. The menu is also a bit distorted but not nearly as bad as the tv display. Should I not waste time replacing the t-con board?

we have no choice but to forget plasma panels. :/ hopefully the lcd panels manufactory improves

To add to why my last post , because some how my screen was fine now I have solarized picture when I watch tv!

Sharp LC-70LE650U 70-Inch Aquos TV TURNS ON WITH PERFECT PICTURE AND SOUND, 5-10 MIN TV TURNS OFF? IF YOU WAIT A WHILE UNPLUG AND PLUG BACK IN TV TURNS ON WITH PERFECT PICTURE AND SOUND? JUST TRIED MAIN BOARD SAME HAPPENED! WANT TO TRY PS AND T-CON BECAUSE TV STARTS OUT WITH PERFECT PICTURE? CAN A BAD PANEL WORK PERFECT FOR 10 MIN THEN FAIL?

On my vizio model P42A due to making a poof sound i opened and replaced a blown fuse then i only had sound no picture so now i changed the y sustain board. I do have picture now but its a bit dark and not clear. I adjusted the picture settings and didnt fix the problem. What would you recommend for me to do to fix the problem?

Damaged board of my Panasoni LCD model TH-l32C20M , Board code Number A01463HN, Please let me know the spare parts center in India, kerala

Helloe,i have an LED TV Samsung with sound but no picture only horizontal lines appear on the screen

Look up "fixing 4k tv with tape", you could actually cancel out one lane on your LVDS/flatcable and get the other half working (there will be a line)

so what if my image Is dim on the right side but is there ... so the backlight inverter went replaced it got the TV on backlights are fine lit end to end just dim on right side

How do solve the problem?

Both of my cables must be unified then because mine is all white.

Panasonic tx -49 led sound no pic only white display

hi i have a samsung tv model #LN46A750R1FXZA serial #ALAU3CNQ707767F.Turn on tv sound good left side of panel is dark an images seem to be in slow motion,after tv warms up it plays fine.that was good for about a month.now left side does same thing all the time.should i check t-con board? ty.

I posted pictures asking for suggestions here. I appreciate any help Norcal715

I am amazed at how many people *WHO HAVE NO TECHNICAL EXPERIENCE* and just want to save a few bucks are saying "Please help me fix my own TV, My TV won't turn on what should i do" Now... Tell me it's not just a matter of time before someone gets a really really rude shock (or worse) from touching something they shouldn't have on the Power Board. ATTENTION ALL NEWBIES WHO ARE TRYING TO SAVE A FEW BUCKS 1. Basic understanding of Electricity and Electronics is MANDATORY before you even consider taking off the back cover of your TV 2. A Basic understanding of Electrical components is MANDATORY 3. Basic understanding of Electrical Safety is MANDATORY as a general rule if you don't know how to troubleshoot and you don't know how to solder and you don't know how to change a capacitor WITHOUT ASKING ON YOU TUBE YOU SHOULD NOT BE OPENING YOUR TV instead Get someone who knows to fix it your life is not worth less than $300, so just pay someone to do it ... ok

Alittle late but you lost that was on plasma and led

vizi uh- ohs

Great video and I think I am going to trouble shoot my Samsung TV to see if the T Con is the cause or the LCD panel. VGA seems to work without any issue but HDMI ports and cable port are causing garbled video and restarting of the TV.

Sorry, forgot the link: badcaps (dot) net/forum/ showthread(dot)php?t=29174

Vizio----Gag ooppss................

Jimmys shop is one high priced, over rated gyp joint, sorry, their youtube videos have nothing to do with help fixing your problem, they're just 2-3 minute commercials anymore...screw jimmys shop its a rip-off