Troubleshooting Gas Boiler Problems: Pilot Not Lighting

No video

Troubleshooting Gas Boiler Problems: Pilot Not Lighting | Full Service Call

Рет қаралды 31,955

Mikey Pipes - Pipe Doctor Plumbing & Heating & Air

Күн бұрын

1st Official Heating Service Call of 2023-24 Season! Gas Steam Boiler - Pilot Out & Unable to Relight! Step by step instructional video for newer techs & experienced ones too!
⚠️Do not attempt this repair if you are not qualified and/or trained ⚠️
Typical Atmospheric Gas Boiler Combustion Results
Stack 325-500 degrees F
O2 4%-9%
CO2 6.5%-8%
CO Less 50ppm
What’s in your Veto? Here is mine:
Veto TP-XXL amzn.to/3zX10vg
Testo Combustion Analyzer: amzn.to/3Zd7naH
Digital Manometer: amzn.to/3EDt5ey
Milwaukee M18 Blower: amzn.to/46iTo6j
Milwaukee M12 Fuel 1/4" Impact Driver amzn.to/3I9yLfI
Milwaukee PVC cutter: amzn.to/3sbrdUc
Mini Waterproof Storage bin: amzn.to/3yfgsEv
Wiha Allen Keys: amzn.to/33ipGmb
HIKMICRO B20 amzn.to/33iGklx
Furnace Switch amzn.to/31X89PT
Milwaukee Light amzn.to/3I38Lmh
Wagos amzn.to/34QoiaU
Milwaukee Set amzn.to/33vnQOz
Torpedo Level amzn.to/3no1oOk
Crescent set amzn.to/3GtZeV8
Wiha 7 piece set amzn.to/3rkISaK
Milwaukee step bit amzn.to/3I395Bv
Thermocouple Flare wrench: amzn.to/3noJZ8s
Ridgid 10” wrench amzn.to/3GvRnqa
Fluke non-contact tester amzn.to/31VQgAQ
Klein drivers amzn.to/3qoe21W
Knipex Wrenches amzn.to/3trzFjS
Klein 11-1 amzn.to/3tpsPLD
12” crescent amzn.to/3A0CZ6S
Gerber Gear Pocket Knife amzn.to/3foaW7I
Yellow Jacket Hand Ratchet amzn.to/3nrDgup
I am on Discord & WhatsApp!
Discord: / discord
WhatsApp Group: chat.whatsapp....
Mikey Pipes Uncensored: / @mikeypipesuncensored
New oval raised silver stickers are from:
Armored Decal Company Inc.
35 Victoria St. E, Unit 9
Alliston, Ontario L9R 1T3
(p) 705-435-6665
(e) ken@armoreddecal.com
(Tell them Mikey Pipes sent you)
Please support this channel and Mikey Pipes and consider the following…
Pipe Doctor FlexFit Embroidered Caps
Minimum donation of $37 is appreciated
(If you are international - please add a minimum of $40 for shipping/postage)
Shopping on Amazon? Please use my referral link amzn.to/2PjjS4v
Sticker Requests:
Do you want a sticker to show your support of this channel? Email your request to me! mike@mikeypipes.com
Name
Address
City, State, Zip
Consider making a donation of $5.00, or ANY amount, to the postage fund! I literally mail out stickers all over the globe. I've sent stickers to HVAC guys in Afghanistan, New Zealand & all over Europe.
PayPal is: office@pipedoc.net
Venmo: @PipeDoctor
CashApp: $mikeypipesny
Want to send a love letter, note or gift? Our mailing address is:
Mikey Pipes
C/O Pipe Doctor Plumbing
80 E Hawthorne Ave
Valley Stream, NY 11580
#localplumber #heating #mikeypipes
Table of Contents:
0:00 Introduction

Пікірлер: 214

@domenicpetruso7751 11 ай бұрын

Mikey Pipes and Steve Lav are wonderful assets of the mechanical KZfaq community.

@PipeDoctor 11 ай бұрын

Thanks

@erichoward5565 11 ай бұрын

Peter has a great mentor. Lucky to have him under your wing. Great lesson for us as well. Even gave Steve Lav a shout out. 😂

@PipeDoctor 11 ай бұрын

Give credit where credit is due.

@JohnSmith-cd8ch 11 ай бұрын

Glad to hear you giving Steve Lav some props. he ain't you but he gets the job done for the customers in his market

@PipeDoctor 11 ай бұрын

Credit due when deserved

@atlasfueloilinc.2421 6 ай бұрын

My first boss always wanted the jacket top always wiped clean before leaving the job. It was impressive for the customer to see a clean boiler jacket and it wasn’t hard to do.

@MrDmadness 6 ай бұрын

Funny that i watch these on days off lol. Good apprentices that take instruction well and also have common sense are pure gold. Before i fully condemn the valves i like to hit the Tc with my small torch to see if theres ANY way it even could work... its more so a curiosity for me at that point. That gas valve got cooked out, likely during yheir basement reno due to dirt.. that damper needs replacing too, its resistance will be high and the failure will happen on the weak part of the low voltage circuit ( looking at you windings for the gas valve solenoid ) . As the amperage ruses against the resisting liad ( like pitted dusty contacts on the damper end switch ) things heat up... till they dont. :)

@PipeDoctor 6 ай бұрын

Thanks for posting your feedback

@MrDmadness 6 ай бұрын

@@PipeDoctor thanks for making videos :)

@johnsutter1497 11 ай бұрын

Thank you for the educational video?

@PipeDoctor 11 ай бұрын

Our pleasure!

@kens.3729 11 ай бұрын

Strongest HVAC Team in New York. Thanks Gentlemen! 👍🙏

@PipeDoctor 11 ай бұрын

🙌

@atlasfueloilinc.2421 6 ай бұрын

I give it to you, remember teaching as you are doing a service call your are going to miss things that you would not, when you are alone and observing as you check out job.

@ethanriley6260 5 ай бұрын

You did the combustion test on my birthday haha

@PipeDoctor 5 ай бұрын

Nothing but hot air

@danielelise7348 11 ай бұрын

I REALLY want Peter to succeed in this field, he's the kind of kid I like getting as an apprentice.Mike you should get a heap of scrap wire of different sizes,so Peter can practice his electrical terminations.

@PipeDoctor 11 ай бұрын

👍

@randymathews3348 11 ай бұрын

By the time you got to the roll out switch I'm like wth are you doin Mikey? Little rusty huh? And who else got flashbacks when Peter started removing burners, thought he was gonna get a free Uber ride home 😂

@PipeDoctor 11 ай бұрын

A little rusty

@Keith_Mikell 11 ай бұрын

I guess thats why you were so impressed i had a standing pilot, bc you like them. lol. My package will get to you monday, they tried sat but no one was at office. Accept it youll love it.

@kens.3729 11 ай бұрын

A Lot of people are Guilty of having their Equipment in a Furnace Room and especially if the Basement is Completely Finished. Highly Recommend Air Grills.

@PipeDoctor 11 ай бұрын

Yup 👍

@peter-pg5yc 11 ай бұрын

In ca it must be open to attic or crawl space for code

@jascoplumbingsupply4224 10 ай бұрын

These types of videos are essential for new techs, and great refreshers for experienced ones.

@PipeDoctor 10 ай бұрын

Glad you think so!

@danielrandolph9170 11 ай бұрын

Good video you put back the old thermocouple i hope scene it wasnt the issue & you save the customer money .

@PipeDoctor 11 ай бұрын

Nope. It was original. Time to replace

@meenanod5413 11 ай бұрын

Excellent work

@PipeDoctor 11 ай бұрын

Thank you! Cheers!

@samarshaikh5601 11 ай бұрын

Always waiting your video

@PipeDoctor 11 ай бұрын

So nice of you

@aaliyakhan2463 11 ай бұрын

This video are really rocking 💞

@PipeDoctor 11 ай бұрын

Thanks 👍

@subhashbhai7403 11 ай бұрын

Video is very nice!

@PipeDoctor 11 ай бұрын

Thank you very much!

@sanjusharma8003 11 ай бұрын

Nothing is impossible 🙌

@PipeDoctor 11 ай бұрын

Correct ✅

@aashasoni3554 11 ай бұрын

Full support 🔥

@PipeDoctor 11 ай бұрын

Yeah?

@beeper7892 11 ай бұрын

Peter seems like a good dude. Give him my number. Looking to hire a new tech.

@PipeDoctor 11 ай бұрын

Ha ha ha

@scottmaz4063 11 ай бұрын

Love that low main vent. Should be up alot higher

@PipeDoctor 11 ай бұрын

It’s actually on the end of a dry return. Yeah yeah I guess a coulle Pio.

@scottmaz4063 11 ай бұрын

We always raised them see the rust and drps on the floor. No more if you raise it. Higher the better.

@eugenkaranxha1659 9 ай бұрын

I love the standing pilot I converted most of my electronics furnaces on my buildings with manual standing pilot and for years they still run like a champ I got tired of the electronics going bad at the worst time or the coldest night they always fail now the tenants will never be without heat

@achdiagnostic7773 8 ай бұрын

You can test the thermocouple by measuring the millivolts. Unscrew it and use two jumper wires. One goes to the end of the tcouple and the other goes to the copper pilot tube. Relight the pilot and measure the millivolts. Normally gets to 25 to 30. If it doesnt the pilot is bad. Sometimes easier than disassembling everything.

@user-bs8zl6dz7g 11 ай бұрын

I tested a thermocouple without installing all the way. 1- remove the old thermocouple from gas valve. Just part that goes into gas valve. 2- put new one in, use lighter or candle to heat the new thermocouple, you can try to light pilot , if pilot stays on , then you know that’s the issue and replace the thermocouple. 2 - threa

@PipeDoctor 11 ай бұрын

Yup 👍

@DJVINNIE 10 ай бұрын

i had to subscribe - Mikey deserves another subscriber - hes great - peter piper too - love the vids! thanks for the knowledge.

@PipeDoctor 10 ай бұрын

Thanks for the sub!

@pets7164 9 ай бұрын

What if the second couple was defective or the pilot was just dirty and not giving enough gas heat to couple or could the Orifice been partially blocked and you could have blowed through it? I was just wondering if you have ever ran into that or even possible? Also want to say I like your name “Mikey pipes”I’m not too keen on your assistance name of “Peter Pan”. You should upgrade him to Peter Piper. I feel that would be a confidence builder for that nice young man.

@AmanSharma-kd1mc 11 ай бұрын

Very good

@PipeDoctor 11 ай бұрын

So nice

@panjavisingh2800 11 ай бұрын

Professional 👌

@PipeDoctor 11 ай бұрын

Thanks 😅

@amansharma-ss6pp 11 ай бұрын

Always be good video 😎

@PipeDoctor 11 ай бұрын

Appreciate it!

@throttlebottle5906 10 ай бұрын

the draft hood looks ok to my eyecrometer via video. it says it should be 8" from bottom of hood to top of jacket, but many of them came short from factory, with not enough pipe from the hood to end and didn't allow for the jacket/insulation. I would look in it to be sure it doesn't have an integrated junk bimetallic strip damper that's failing to open anymore. the powered damper looks very suspect to me, more so when wiggled and hearing the end-switch click, as well as not stopping every 180 degrees. unless they modified them to make a full revolution each cycle to self clean and not stick(none that I know of, but it's possible) 🤔

@williamloder9194 11 ай бұрын

I also support having the old fashion standing pilot. Much simpler to diagnose. That draft hood sure looks like it was shortened.

@PipeDoctor 11 ай бұрын

The draft hood was definitely cut back

@williamloder9194 11 ай бұрын

I went back to view the video. It looks like there was a draft damper was installed on the verticle. There is a bracket still mounted just above the hood. Someone replaced the old damper with a new damper on the horizontal. If the damper had been installed where it is now, the hood might not had to be cut@@PipeDoctor

@randymathews3348 11 ай бұрын

Ok I got to the end, what was the reason she didn't fire right up? Was it the damper or one of the safety switches was still disconnected?

@PipeDoctor 11 ай бұрын

Gas valve. Did you not watch the video??

@randymathews3348 11 ай бұрын

@@PipeDoctor I watch the whole thing. She didn't fire after the valve change when you hit the er switch. You went back to the damper then cut away

@PipeDoctor 11 ай бұрын

@@randymathews3348 kidding me? I finished the video doing a combustion analysis on the boiler running.

@randymathews3348 11 ай бұрын

@@PipeDoctor yes you did, even had your little baggie. But why didn't she fire when you hit the switch is what I'm asking Mikey

@captainwho1 5 ай бұрын

I know this video is very old but I had the same question. I was expecting it to be a bad flue damper control.

@stevesolt4036 11 ай бұрын

Thought you said to get a wire nut. But it must have been get a Wago. 🥴

@PipeDoctor 11 ай бұрын

👍

@atlasfueloilinc.2421 6 ай бұрын

I don’t mean to be critical on Peter I just know from the kids I made into union A Mechanics. He looks worth the investment, he needs more hands on to have the confidence. Good job

@johnwalker890 11 ай бұрын

Good job Mike and Pete, The low voltage wires shouldn't be in the conduit or line voltage box service disconnect, NEC code from way back, And they can put vent covers in the drywall, or install a vent from outside for air make up or O2 vent for combustion.

@everettstevenson2111 11 ай бұрын

Mikey might want $16,000 dollars to bring the whole heating system up to spec.

@justmc62 11 ай бұрын

It's not the best practice but as long as the insulation meets or exceeds the maximum voltage within the enclosure/ raceway it is allowed by NEC.

@johnwalker890 11 ай бұрын

If they are dumb enough to pay that price, then good luck, I need to sleep at night, don't need to be tossing and turning in my bed, worried about someone knocking on my door, wanting their money back.

@PipeDoctor 11 ай бұрын

Maybe 🤔

@johnwalker890 11 ай бұрын

Just leaving a comment on the internet is dangerous enough, some guys go crazy just telling them what to do, they go nuts.

@arushichawal7606 11 ай бұрын

Looking nice

@PipeDoctor 11 ай бұрын

Thank you! Cheers!

@jasongeo2 5 ай бұрын

Just thread and Slide it in Peter....owwwwww😂

@PipeDoctor 5 ай бұрын

lick it first too

@jasongeo2 5 ай бұрын

@@PipeDoctor 🤣

@NYCHvac 11 ай бұрын

The wooden door for the boiler room is fucking hilarious 😂😂 definitely fire department would love it

@randymathews3348 11 ай бұрын

It's not an issue as look as clearances are meet. The entire room is framed w wood studs

@PipeDoctor 11 ай бұрын

Did you forget about combustion air for a combustion?

@NYCHvac 11 ай бұрын

@@PipeDoctor not at all doc. You covered it on the video very well. I usually don’t comment on things the doctor already covered. But yea contractor put up walls they never take it into account

@nebbrooklyn5966 4 ай бұрын

I’m surprised u didn’t condemn the boiler lmao😂

@PipeDoctor 4 ай бұрын

Not yet!

@atlasfueloilinc.2421 6 ай бұрын

Does Peter study your videos on his own time to learn or just at working hrs. Most young apprentices only want to learn on company time, no extras.

@jochemsluis8834 11 ай бұрын

Sometimes we over look the obvious. I have been guilty of this after so many service calls and go deep then switch it on after awhile.... Sometimes you need to start from scratch at check the vitals.

@Hvac-dude 11 ай бұрын

Thanku 😊

@PipeDoctor 11 ай бұрын

No thank you

@ericmilburn9841 7 ай бұрын

pilot flame looks lazy. burners were dirty. gas valve did appear to have been flooded at one time which the manufacturer does recommend replacing if ever flooded. Over all as a teaching video not bad. and every one trains different. i was trained to never leave a unit dirty as it could result in a nuisance call back which can be hard to charge the customer for and could affect your combustion analysis. i do enjoy your video's, in my area we don't have many steam boilers they are mostly hydronic. Keep up the good work at making the trades great again!

@stephenzies8867 11 ай бұрын

When I Was Born The Doctor Told My Mother, I Did All I Could But He Pulled Through Anyway.

@PipeDoctor 11 ай бұрын

And you came out halfway decent

@ranjitsharma7956 11 ай бұрын

excellent job 🤟

@PipeDoctor 11 ай бұрын

Thanks a lot!

@scottlaferriere4499 11 ай бұрын

Hello Mike, you make mention of it not being OK to mix the high and low voltage in the same J box but it is actually OK. It’s got more to do with the insulation class on the wire. As long as the insulation class meets or exceeds the maximum voltage to be seen in that J box or conduit it is fine, as for example if you were to use THHN on the low voltage in the box with high and low voltage, it would be fine and per code. Also maybe show Peter on how to check DC millivolt for thermocouple troubleshooting.

@PipeDoctor 11 ай бұрын

Okay. Please explain that to the inspector on my next job if I decide to mix voltages.

@scottlaferriere4499 11 ай бұрын

Mike here is the code to reference National Electric Code Article 300.3 (C) 1. Conductors of different systems when asked.

@throttlebottle5906 10 ай бұрын

the thermostat wiring entering/passing through a line voltage box is a violation itself, because it's "class 2 low voltage wiring", which is not rated for, nor ever enter line voltage areas. yes, even though some has been rated up to 300 volts max, it's still a violation. it would need a box divider, a separate nipple connected box or the transition splice done outside the jbox, then it would still be an violation at the jbox on boiler. that's same reason condensers and most equipment have a small compartment just for low voltage wiring to be spliced and then internal wiring is different, where it's allowed to be in close proximity. also, it may still be against local state, city, town and other codes. they always override national code with greater restrictions, some overrule it by using older code base though.

@fallingdebris4391 9 ай бұрын

They definitely can't share a conduit

@efrianlavine850 11 ай бұрын

Love it milivolt tech 101. Very old, but pretty robust 80% safety system. Very inexpensive parts. I remember when electronic igniter s happened. They were so unreliable for years. AND parts were outrageous costly.

@PipeDoctor 11 ай бұрын

Thanks for watching

@nilolee2426 7 ай бұрын

Hey Mikey, I spend at least an hour to 2 hrs everyday watching your vids😅, I would really appreciate if you can answer or advice my concerns. I have this boiler hydronic system with 2 zone valves since 1987 without any problem like roll out flame,,etc. it’s a Utica gas boiler m6125agbt and doesn’t have draft hood ,no spill and roll out switches. Im learning now all these safety features in your videos. Do I need to make some improvements and install all these now? Thanks in advance

@PipeDoctor 7 ай бұрын

You are perfectly fine. When the system is replaced you new equipment will incorporate those safety controls. I doubt you don’t have a draft diverter. It’s built in.

@nilolee2426 7 ай бұрын

@@PipeDoctor you’re the man, thank you so much and God blessed

@pankajola1625 11 ай бұрын

Good ♥️

@PipeDoctor 11 ай бұрын

Thanks

@andrewgarcia4161 10 ай бұрын

I want to move to NY and work for you as an apprentice

@purehuskybreed 6 ай бұрын

More details where did you to adjust it

@jasonflynn3972 11 ай бұрын

#2. Thanks for feeding us

@PipeDoctor 11 ай бұрын

You’re welcome 😊

@atlasfueloilinc.2421 6 ай бұрын

Is Hartford loop close nipple leaking under pressure. Brown water stain seems very low down, maybe bad gauge glass washers.

@everettstevenson2111 11 ай бұрын

Hey Mikey, of Mikey Pipes Plumbing not easy being cheesy. I like your podcast/social media. I guess some of your customers still checking in on you. Hmm, troubleshooting?. I don't know Mikey, but back in the day dealing with most women. I would have been replacing that old rust bucket, for a new rust bucket. Again where is the automatic feed water control? Love you buddy, jolly good show old boy, God save the King.

@PipeDoctor 11 ай бұрын

The automatic feeder is at the supply house. Where it belongs!

@everettstevenson2111 11 ай бұрын

I don't know Mikey, our code books here in Washington, D.C. goes back too the 1890's, must be a State of New York thing.@@PipeDoctor

@tedbell4416 11 ай бұрын

Hey Mikey

@PipeDoctor 11 ай бұрын

👋

@Al-sq5ti 6 ай бұрын

Low voltage in any state must be seperate from line voltage

@PipeDoctor 6 ай бұрын

Correct. Unless mfg specifies otherwise. Like Burnham.

@williamgildea8348 11 ай бұрын

You never told us what the actual problem was. Even with the pilot out the vent damper should of opened. Was it the damper?

@PipeDoctor 11 ай бұрын

Did you not watch the video?

@williamgildea8348 11 ай бұрын

I did, after you replaced the gas valve it still didn’t fire up. You started to look at the vent damper and then the video cut to you doing the combustion analysis. I was just curious. Even watched it again

@gtpforever 11 ай бұрын

@@williamgildea8348 same thing I seen. Was wondering the same thing.

@bigdaddy4975 9 ай бұрын

Steve lav is a part’s changing hacker

@everettstevenson2111 11 ай бұрын

bravo 4 , 2 charlie goto 38474.38MHz

@PipeDoctor 11 ай бұрын

😂

@consolidatedplumbingandhea4390 11 ай бұрын

That mushroom vent hood looks awfully low? Some of the power-stealing thermostats caused the vent dampers to go round and round on single zone package boilers. like a steam boiler. I commented on the vent hood before you did ;)

@PipeDoctor 11 ай бұрын

i've never had that happen to me

@consolidatedplumbingandhea4390 11 ай бұрын

Around 1980's to 2000 roughly, I would do a new steam boiler, turn it on and the vent damper would go round and round. The issue was the thermostat, change it out or put a relay in and the issue went away. You would see it mostly on the clock thermostats you put the pins in. @@PipeDoctor

@bruceelias2732 11 ай бұрын

Mikey When you set your home air-conditioning to 66 and it's like 59 like last night, will that shorten life of compressor etc, because I hate when it's humid and 65 outside and I don't put air on cause of above concern ?? TX Mr pipes❤

@PipeDoctor 11 ай бұрын

Nope

@throttlebottle5906 10 ай бұрын

get a dehumidifier? it will extract humidity and not cool the home, even heat it somewhat due to natural losses. 😉 A/C is really not meant to be ran with indoor air temp and suffers great efficiency loss.(it can cause coil icing and liquid flood-back which can kill compressor) and for sure not such low outdoor ambient temps(head pressure may be too low) which drops the total system pressure too low and may cause indoor coil icing due to refrigerant temperature being too low. some heat pump models may be OK depending on design, ideally you'd need an outdoor fan cycle switch, indoor coil temperature/ice sensor to cycle the condenser. all that said, it may work OK doing so for short periods, but again, get a dehumidifier, seal the home better and make sure bathrooms/kitchens are ventilated to help curb additional indoor humidity. also if you have aquariums, water fountains/features and whatever else indoors, you need to run dehumidifiers anyway.

@anthonybuonagurio-gl9bg 11 ай бұрын

I didn't see you check for gas pipe leaks

@PipeDoctor 11 ай бұрын

We did

@MichOutdoors 11 ай бұрын

Great video.. brunt boots are junk... Redwing boots the best

@PipeDoctor 11 ай бұрын

Good to know!

@richardwasiluk3801 11 ай бұрын

Peter will b a great plumber if he stays with u n the future

@PipeDoctor 11 ай бұрын

That’s the plan

@atlasfueloilinc.2421 6 ай бұрын

Draft hood looks short.

@christopherchance4860 11 ай бұрын

Hey Mike, is it code for you to use grip. We don't use it anymore up by us

@PipeDoctor 11 ай бұрын

Grip?

@dmatula811 11 ай бұрын

Anothe I D 8 error. Fire needs air. Thought that everyone knows that.

@PipeDoctor 11 ай бұрын

Everyone with common sense knows that

@BeardedBeta 11 ай бұрын

Interested about have double 90’s on the pressure relief?

@PipeDoctor 11 ай бұрын

I guess I overlooked that.

@fallingdebris4391 9 ай бұрын

Before the diverter otherwise you'd be adding outside air to the analysis

@zwwz4537 11 ай бұрын

Are wagos a good replacement for wirenuts for 120/240v applications?

@danielelise7348 11 ай бұрын

Short answer,yes absolutely.

@PipeDoctor 11 ай бұрын

Absolutely

@dillrajkapur8466 11 ай бұрын

💯💯💯💯💯💯💯

@PipeDoctor 11 ай бұрын

Love ❤️

@johnphillipsplumbing7148 11 ай бұрын

You need to get a covid self test my friend. You sound like you have a cols coming,that's how i sounded before i popped positive,oh and i think i'm the best plumber😅😅😂

@jameskitzmann6268 11 ай бұрын

My customers for the most part think i'm the best Plumber. Some think i'm an ass hole but use me anyway. Keep them wrenches turning!

@MokenaBob 11 ай бұрын

Long Sunday video

@PipeDoctor 11 ай бұрын

Thank you for watching

@StanleyH01 10 ай бұрын

Hi Mike, why did the roll out switch burn out? It happened to my gas boiler a few times last winter.

@PipeDoctor 10 ай бұрын

Flame roll out

@ramsheeta5016 11 ай бұрын

Hello ... Long time

@PipeDoctor 11 ай бұрын

Thanks 👍

@spartus56996 11 ай бұрын

You keep the A/C set to 66* at night ? Does the system keep up with that setting easily ?

@PipeDoctor 11 ай бұрын

Yes it does

@peter-pg5yc 11 ай бұрын

I just open windows use a commercial fan and home is in low 60s.. ahhhh san jose ca..

@mitchdenner9743 11 ай бұрын

What was that, barny miller theme song?

@PipeDoctor 11 ай бұрын

👍

@anthonybuonagurio-gl9bg 11 ай бұрын

You probably need the C wire

@PipeDoctor 11 ай бұрын

Yup

@EliteAireServicesLLC 11 ай бұрын

Wood door, wood studs and i bet its not fire rated drywall 😂😂..

@PipeDoctor 11 ай бұрын

Hollow door

@scottpycik 11 ай бұрын

Hey has Peter used the sman yet?

@PipeDoctor 11 ай бұрын

I don’t think so.

@kkovler1 11 ай бұрын

There is no easy way to determine if the thermocouple is good without replacing it?

@randymathews3348 11 ай бұрын

Yes, you test them w a meter

@PipeDoctor 11 ай бұрын

Yes, you can test it with a multimeter that can read millivolts but it’s not worth it. It’s not worth wasting the time. It’s a cheap part.

@josehuertas2441 11 ай бұрын

Why can't you come to the bronx for a Conversion???

@PipeDoctor 11 ай бұрын

Gas in house?

@doncaranci2547 11 ай бұрын

Mike, If you keep telling him what to do, he will never learn. No more lefty loosey etc etc Let him go He will get it

@PipeDoctor 11 ай бұрын

Yeah, but I’m not gonna waste time on the customers dime

@atlasfueloilinc.2421 6 ай бұрын

Also tell Peter mechanics don’t use their phones for a flash light, they use a flash light. Does Peter carry his own flash light on his person.

@joed9908 11 ай бұрын

Why do people have so much combustible stuff in their boiler room. I see you will be going back there soon to replace that water valve below the gas replacement you just did.

@PipeDoctor 11 ай бұрын

Real estate square footage is expensive

@subhamchanchalani1563 11 ай бұрын

💥💥💥💥💥💥

@PipeDoctor 11 ай бұрын

Thanks

@diveshkumar8337 11 ай бұрын

🥳🥳🥳🥳🥳

@PipeDoctor 11 ай бұрын

Thanks 👍

@khushalrajput1441 11 ай бұрын

🎉🎉🎉🎉🎉🎉

@PipeDoctor 11 ай бұрын

Thanks a lot

@scottmaz4063 11 ай бұрын

Nest thermostat junk

@PipeDoctor 11 ай бұрын

Glorified hockey puck.

@siryaalli2757 11 ай бұрын

We want to meet you 😍

@PipeDoctor 11 ай бұрын

Are you sure?

@anihasaini8092 11 ай бұрын

🤠🤠🤠🤠🤠

@PipeDoctor 11 ай бұрын

@scottmaz4063 11 ай бұрын

#1 hi mikey

@PipeDoctor 11 ай бұрын

Congratulations

@scottmaz4063 11 ай бұрын

For 35 years we put thermostat wires in the junction box. Manhattan queens Brooklyn bronx long island. Now all jobs were inspected and passed. Now you say you can't anymore but why. Shoot me picture of the code please. Thanks Mikey 😊