How To Replace EGR Valve 2006-10 Ford Explorer

Рет қаралды 58,910

2 жыл бұрын

Shop for New Auto Parts at 1AAuto.com 1aau.to/c/86/s/egr-valve
The EGR valve helps to reduce pollution by directing some exhaust gas back through the combustion chambers. If the valve is stuck the system won't work correctly, and if it leaks the engine might stall or not start at all. This video shows you how to install a new EGR valve on your 2006-10 Ford Explorer.
• Check here for more videos on the 2006-2010 Ford Explorer • Ford Explorer 2006-201...
This process should be similar on the following vehicles:
2006 Ford Explorer
2007 Ford Explorer
2008 Ford Explorer
2009 Ford Explorer
2010 Ford Explorer
Tools you will need:
• Pocket Screwdriver
• 10mm Socket 1aau.to/osy/1AXAA00017
• 8mm Socket 1aau.to/osy/1AXAA00017
• Ratchet 1aau.to/oxN/1AXAA00016
• Torque Wrench 1aau.to/oon/1AXAA00044
• 1-1/16 Inch Wrench
Subscribe: / @trq
Check out our playlist:
Ford Explorer 2006-2010 4th Generation: • Ford Explorer 2006-201...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 48

@TRQ 2 жыл бұрын

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

@mdcoram Жыл бұрын

By far the hardest part of this job is that back mounting bolt. That bolt alone took me 40 min and the entire process was 65 minutes... this video shows him removing that back mounting bolt by hand :). Still a very helpful video. Probably wouldn't have tried it on my own without it. Many thanks.

@edwardrinehart2125 2 жыл бұрын

Thank you. This is the most complete method for replacing this Valve on the site. When I removed mine the vacuum hose connecting the two inlet/outlet tubes on the valve was missing. I couldn't find any information on what connected to those spouts. Your very clear video showed what went there. I suppose a new valve would have had the hose on it as yours did, but I didn't need to replace the valve. I even removed the Intake Manifold trying to find the "non-existent" vacuum hoses. I wish I had found your video prior to that!

@genewilson6262 Жыл бұрын

Why didn't you show the replacement of the new egr tube that's on there

@montrose5paulina 11 ай бұрын

Videos are ok, it would be GREAT is you explain why you’re replacing the part or symptoms.

@cwsosby 2 жыл бұрын

It’s that last bolt you didn’t show that worries me. But you have given me hope. Thanks for the awesome video!!!

@TRQ 2 жыл бұрын

+Fire1776 Thanks for watching our video! 1aau.to/m/Shop-TRQ

@calvinpryor 2 жыл бұрын

I was thinking the same thing.....the second bolt for the EGR valve itself. looks like that one will be a bugger to get to !!!!!

@jorgemori2800 2 жыл бұрын

Woww...This is the best video I've seen so far about this problem...I will give a try next week. Thank you guys.

@marcosgonzalez6545 2 жыл бұрын

Best and cleanest how to I've seen. Thanks for the info!

@chucktripp7742 2 жыл бұрын

You did a fine job in making that video. Simple! Easy to follow. Thank you. Have a blessed and wonderful day. Chuck, Mobile mechanic. 😊

@POCo333333 8 ай бұрын

Crazy helpful video! Thank you. Those back mounting bolts are no joke! My first time working on my truck was a success

@danthemen87 Жыл бұрын

Great video, very well, clear voice. Easy to follow, thank you for making such a good video

@bcom9389 3 ай бұрын

A very good informative video. You should have mentioned that now is the time to replace the throttle body assembly since explorers do have issues with them anyway. It appears you just now replied your throttle body assembly as well. Good informative video though 👍

@briannalareau5140 2 жыл бұрын

This was very helpful. Thank you

@erickwilson3238 2 жыл бұрын

Thanks I've seen a couple of videos and this is the route I'm going to take

@lukest.jacques3103 Жыл бұрын

Video was perfect thank you very much!

@armsallowed Жыл бұрын

Wonderful brother , your knowledge transfer is very easy for me to learn from

@calvinpryor 2 жыл бұрын

this has better instructions than the Haynes manual. The manual didn't show the nut on the upper left throttle body. And the manual doesn't have the bolt sizes. Sooooo handy !!!!!

@isakwilkinson2491 7 ай бұрын

I appreciate your video it's totally awesome but you really make this stuff look super simple and easy but I think I can do it thank you so much I was going to buy a 2010 Ford expedition and now I think I'm going to go ahead and buy one cuz just a little bit of problems that you describe or that I saw those are all easy fixes thank you so much for the video keep making more videos

@papawsgaming8762 11 ай бұрын

I see he must have cut out the part where he was swearing while removing that last 10mm retaining bolt. cant for the life of me get that out

@tribzter 3 ай бұрын

Awesome thanks that helped a lot The rust belt makes it so much more difficult though.

@randallconrad2600 Жыл бұрын

Thank You very well done video appreciate you

@carmanfedele5445 10 ай бұрын

Fine job young man!

@tw5443FlyingTiger 4 ай бұрын

Great video. Thanks

@nmdelninno Жыл бұрын

Nice Job. I've got a 2005. Any major differences installing?

@BadRonald1 Жыл бұрын

Good deal that was fast, no fuss no muss….. good job

@4freevid Жыл бұрын

My red/black hose is cracked before the rubber, It's probably my issue besides the EGR but I definitely need to fix the hose. What is that part called and do you have another video by chance to show its replacement?

@deejaysalruiz4447 2 жыл бұрын

How can i go about replacing the egr wire harness connector for a 2008 ford explorer ?

@bojo8141 11 ай бұрын

Very informative. Thanks

@TRQ 11 ай бұрын

+BobJ Thanks for the feedback! 1aau.to/m/Shop-TRQ

@aglerfamily 2 жыл бұрын

I have a 2005 Explorer. Are the steps near identical?

@jjjjjjjjjjjj260 Жыл бұрын

So much easier then older models.

@davidpersonful Жыл бұрын

Would this be the same for a 2008 Edge?

@Zekiel559 Жыл бұрын

Would this be the reason why my 02 sensors come on I just replaced them all

@rickymartinez4950 2 жыл бұрын

I have a 2010 ford sport trac the problem is that when I try to drive off the truck doesn’t move it gives a little push but from there nothing it’s like if I had the hand break on but obviously it doesn’t same when I try to go back it does the same. When I change gears it also makes a small bang i put in the FIXD system scanner & it says this is the problem but I want to be 100% sure

@horussebeck651 Жыл бұрын

Buenos consejos pero podrían poner subtitulado gracias

@MohammadWassef 4 ай бұрын

does it work with out removing the throttle body ?

@RiccoFX Жыл бұрын

How about with the 4.6L v8 engine?

@airbrushinmotion 9 ай бұрын

What is the hose called at 38 seconds into the video? I broke mine taking it off

@theprofessionallp3399 Жыл бұрын

Hi TRQ, I just replaced the EGR and after I replaced it came squeal noise like whistle. What suppose to do can anyone help me. Thanks

@altodude890 11 ай бұрын

I replaced mine 2 years ago and it looks like it has already failed . Has anyone had this happen before ? I even used the motorcraft replacement. Maybe needs to be cleaned ?