How to Replace Front Strut Assembly 2009-2014 Ford F-150

No video

How to Replace Front Strut Assembly 2009-2014 Ford F-150

Рет қаралды 41,325

Жыл бұрын

Buy Now!
New Strut & Spring Assembly from 1AAuto.com 1aau.to/ib/1AST...
This video shows you how to install new front strut assemblies from TRQ on your 2009-2014 Ford F-150. TRQ Struts are made to fit your vehicle exactly, just like the original part. Struts can wear out as early as 50,000 miles. You should inspect them regularly for leaks or wear. Save time, money, and hassle by replacing an entire strut assembly.
This process should be similar on the following vehicles:
2009 Ford F-150
2010 Ford F-150
2011 Ford F-150
2012 Ford F-150
2013 Ford F-150
2014 Ford F-150
Tools you will need:
• Pry Bar 1aau.to/oTm/1AX...
• 10mm Socket 1aau.to/oa9X/1A...
• 13mm Socket 1aau.to/obtN/1A...
• 15mm Deep Socket 1aau.to/obtN/1A...
• 15mm Socket 1aau.to/obtN/1A...
• 18mm Socket 1aau.to/oagx/1A...
• 21mm Socket 1aau.to/oagx/1A...
• 27mm socket 1aau.to/oW/1AAS...
• 30mm Socket
• 8mm Socket 1aau.to/oa9X/1A...
• Trim Tool Set 1aau.to/oaaS/1A...
• Locking Pliers 1aau.to/okG/1AX...
• Torque Wrench 1aau.to/oaD5/1A...
• Bungee Cord
• Copper Anti-Seize
• Gloves 1aau.to/o5w/1AX...
• Safety Glasses 1aau.to/oWI/1AX...
• Floor Jack 1aau.to/o42/1AX...
• Hammer 1aau.to/oTQ/1AX...
• Pole Jack
• Rubber Mallet 1aau.to/ogM/1AX...
• Wheel Chocks
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 20

@TRQ Жыл бұрын

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

@tomlampros7122 4 ай бұрын

Excellent step by step video. If only all jobs were this clean. Thank you!

@LarjFarvaable 9 ай бұрын

At least for 2014 models, the bottom end of the strut is held by a different (and much easier to work with) attachment method than the one shown in this video. Make sure you plug your exact year and model info into the A1 website rather than just ordering the product link in the video notes. That said, this was the most detailed video on the process I've seen. Very nice

@JanisFever 11 ай бұрын

Thanks for the Video! Some of these bolts were tough, especially the sway bar and others that got loose and spun. I used a vice grips to stop the spin, and had to heat the bolts with a torch to loosen them up enough to stop the vice grips from sliding. Wasn't easy, but with your video I was able to get it done.

@jamesmoorman7328 20 күн бұрын

All of the nuts that were removed in the video are not reusable and need to be replaced after removing. The Hub/Spindle nut will definitely back itself out if not replaced, it’s only 30ft/lbs and requires the neoprene to hold it in place.

@scrapppy96 21 күн бұрын

are you supposed to loosen the middle bolt on the strut once its assembles?

@dog0182 Жыл бұрын

I have seen many videos without taking all of this parts.

@20807shane 6 ай бұрын

Though it’s been quite awhile since I’ve changed shocks, I don’t t remember ever having to take all that a loose.

@valleyquail1790 9 ай бұрын

Rookie question: is there a reason why you don’t use anti-seize on the nuts and bolts before you reinstalled them? Thank you

@avrilgreen4049 Жыл бұрын

Se puede cambiar solo el amortiguador? Debemos comprimir el resorte?? Gracias

@ryantalbot6671 5 ай бұрын

Bravo! best Video for this! Thank you for making it

@user-wc1rv7qr7s 11 ай бұрын

Grateful for this info

@jeremyjohnson933 10 ай бұрын

What kind of grease goes on the end of the CV upon reassembly? Mine did not have much, most got wiped on my shirt while fighting the control arm bolt. It looks like the needle bearings in the hub could use a little too.