I found your video extremely useful. I have a kitchen tap which is of similar design. It is only about 3 years since it was installed, but it is leaking! What I mean is; the tap is dripping. So I think the ceramic cartridge needs to be replaced. You have shown me how to go about it. I had no idea how to access the cartridges, just pull off the handles. How easy is that?! I had no idea where to source the replacement cartridges. I was totally unaware that Tool Station stocked them. You have shown me the way forward and increased my confidence in tackling the task. Thank you so much. I am extremely grateful. Keep up the great work.

The spline orientation is fixed in relation to the fully open/closed valve. To get the handles to align you need to fractionally tighten up or loosen off (riskier option) the whole valve with the spanner. In your case if you can 'nip up' the cold valve a little more then you should be able to get the lever more upright.

It's is DEFINITELY worth noting that not all handles just pull off the taps. I work for B&Q in the kitchens section and the majority of the taps will sell will require you to remove a grub screw before you can take the handle off, in some cases this is a hidden grub screw, it could be hidden behind a cap or a cover or something. I haven't ever seen any that just pull off like yours did! Worth noting for sure because if anybody is attempting to pull them the same way you did they may be confused as to why they aren't getting anywhere

Great video vince a Tip there's also a filter at the end of the tap that builds up dirt it's good to open it and clean it out so the water runs much smoothly I enjoy every one off your videos peace ✌️

I've had a leaky tap for months but seeing how easy it can be I think I'll go for the fix instead of buying new, great video

re pulling off the handles, the lever in mine screws into that handle cap, and acts as a clamp for it. Unscrew the little lever to release the grip and the handle cap comes straight off. Top video. Thanks.

love this real life house hold fixes. you are always so entertaining! greetings from Montreal!

I actually did this on a similar tap a couple of weeks back; the hot side was leaking and every time we turned other taps on it made a whistling noise in the pipes! The version I have has a big plastic gear which fits on the cartridge and in the tap body, and that has much finer teeth for adjustment of the tap position. I did have to adapt the plastic gear a bit though, as it needed to sit further down on the shaft to get the tap tops nicely aligned. Used exactly the same cartridges as you, and I was surprised how cheap and easy a fix it was. I used a tiny smear of silicon grease to help the rubber washer when tightening the cartridge, but I also use Fernox a lot too.

After an hour of searching I finally found a video that demonstrated how to remove the gooseneck instead of lifting off a collar. Mine didn't have an obvious allen wrench location and I could not for the life of me figure out how to get to the O rings (already replaced the cartridge). There was a spot in back with a rubber whole plug that matched the look of the neck. YOUR video helped me to look closer once I realized the whole thing lifted out of the collar. Replaced the O rings and good as new. Cheers mate!!

Interesting video thanks Vince! I know next to nothing about plumbing so will be handy for the future!

Love the safety warning for a tap fix. You never know what can happen!

I have done this sort of repair before but firstly looking at a youtube video beforehand, great vid vince

I love these in house fixes something different then only repairing devices and things (i also love that but something different is also nice ) nice video vince

Thanks for the video. My tap was leaking and it was the washers. Easy to fix when you know what to look for and how!

Enjoyed the vid as always. Thanks Vince. 👍

Great video, Removing the blue/red silicone seal and the top circlip should disassemble the cartridge, there should be an inner o'ring that has failed 👍👍👍👍

Nip it up or back half a turn and that'll get that tap head on straight.......ceramic inserts are a nightmare, they just wear away......well done buddy on the fix

I had an identical tap leaking from one side but when that side valve was opened, not when closed as your situation was at beginning of video, that cartridge u can actually disassemble and it has some small o-ring that's perished and u can try replace it, or better yet replace entire cartridge like u did, remember when u removed circ-clip, that let's u pull out the middle pin which exposes the small o-ring I mentioned earlier on.

Thanks Vince - saved ma a new tap 😊 I found that I didn’t need to turn off the taps - Which was good as I didn’t have a convenient way of cutting them off. Won’t be so cheerful if I need to change the cartridges. Until then, thanks again.

Excellent Vince, I have a similar tap in my kitchen that's leaking that ill now try to sort out. Other half has been on my case for months about it. Mick 👍🤣🍻

Very good. I'd have done the lime scale on the tap end where the water comes out as well. Think if you'd tightened the cold that little bit more it would have been straight like the hot, yes i have ocd as well lol

Thanks Vince, very helpful. Was able to do the job and not have to spend £100 with a plumber.

i really needed this video ! thanks vince

Also regarding the spline orientation, if you cant tighten up the valve any further you could use some PTFE tape on the valve thread, that will give you some 'thickness' to play with.

Had the same issue with the FRANK taps replaced the washers then found a hole in the spout. Lucky for me someone was selling a used one for 10 Euros so I now have spare parts for this really Expensive tap!

Today is a lovely day, 4 video from my favourite youtuber

‘O’ rings, whatever sort, need to be lubricated for fitting. Using WD 40 is a great idea. Alternatively Vaseline is a good choice. There are specialist lubricants or greases available but they tent to very expensive. I think the grease that you used is silicone. Whatever lubricant is used, you only need to apply the slightest smear. Apply Vaseline to the ‘O’ ring and using your fingers wipe off the excess so that the ring is shiny but no visible sign of the grease. This is based on my experience as an engineer dealing with military applications.

Great video, Vince! I've not heard of that LSX stuff before, but I feel like I need some of that in my toolbox. I have about 100 rolls of PTFE tape and seem to use that on everything 😂😂

Hi vince brilliant job 👏 👍 Ps if you take the right hand tap back off and turn the brass nut up a couple of mm the taps should line up on the off position again 😉

Great video!

The most useful video on KZfaq I’ve watched this year 👍🏻

Brilliant! Helped me out big time! 😊😊😊😊

Clever geezer I must say Vince you do not give up easy LOL

Great video. Wish I could have watched it a few months ago before I paid for a new tap and plumber to fit it.

We are totally spoilt today with all these videos in one shot!!! =D Got the same type of tap, this is something I need to do!!! This was super useful! I am thinking I need to replace the same parts you replaced there - it looks identical, but I have it dripping from the spout too. I am guessing either my hot or cold valve (internally) has limescale or bad washer - that's different to your faults I think? What do you think? It is identical to yours though!

Lol these home fix videos are very refreshing

Hi Vince, The answer to all your latest videos regarding plumbing items is: a) red wine vinegar with 5 or 6% acidity (plain wine and water ingredients and nothing else) and b) a suitable container (shape-wise) to accommodate each of those items so you don’t waste too much of that vinegar (yes, the cold/hot water valves had to be replaced). It’s important that you‘ve got some kind of a plan to every day’s choirs because you must let them soak for at least 24 hrs. A chrome layer or stainless steel items won’t be affected but be careful with galvanized or zinc layered items that the vinegar might go through and remove that layer. When I was in UK, I found that Cillit Bang (or similar products) was waste of time on heavy scale deposits. So, on items that cannot be contained, a towel spread over big surfaces (like the sink area) or wrapped around others of a more awkward shape and literally drenched with vinegar that you keep on “topping up” for around 24 to 36 hours, was a better option. After vinegar treatment, scrubbing off with the green side of a scouring pad on stainless steel items, finished them off nicely (not always suitable for mirror finished items, you need to check). Finally, to preserve O-rings’ life, for those that takes some time to be used, dust some talc powder on them.

Thank you so much. An absolute massive help.

1st class video to watch thank you take care kind regards from me kenneth

Thank you, one of my next tasks too. cheers

Helped a lot. Thanks

You can actually dismantle the cartridge, In the stem you will find ANOTHER O ring! Mine regularly need cleaning every 2 or 3 years because of lime scale.

You forgot to clean out the filtre in the front from scale and calc thats why the flow of water is not straight

Top video mate.

Man of many talents

Hey Vince! Just a weird observation / tip! I wrapped some kitchen towel around my taps, where the limescale was bad; secured it with elastic bands, then soaked the paper towel in IPA! Left it for about 30 minutes, then all the scale & black marks just brushed away with a stiff toothbrush! 👍🏼

Inside those handles there may be a plastic incert that may can be removed and rotated. Try different positions to get the handles lined up correctly.

16:02 Your neighbors must've thought there was an earthquake outside lol

When I do these it is always seized up , good video, . In your switch bits would you have a switch game card reader/ headphone jack board that you could spare , it doesn’t have to work. Keep the videos coming, all the best

The honey do list is getting knocked out :P excellent vids!

If you need to tighten the base, I would get a long tube-like wrench as it makes it sooo much easier. I spent ages faffing about with different types of wrenches before getting one.

Thanks very helpful video 👍

Job well done Vince. Forget the cillit bang though. Get silvo on the chrome and your wife will think you have a new sink!

My Mate Vince here be fixing an entire house to sell on Ebay

02:49 a tip worth noting is always put the plug in before undoing screws as they end up down the plughole !!! Edit 4:30 I see you just realised LOL

actually you can remove the red/blue silicone ring at the bottom of SOME inserts and turn the ceramic part around to change open/close direction.

good job mate.

Superb, no leaks here either, thanks mate

great fix :)

I have this exact fix on my to do list.

Hi Vince Thank you for the great video. Quick question- I had a look under my sink and looks like I don't seem to have the stop valve that you gave a 1/4 turn to stop the water supply at the start? Any tips?

Helpful information. I have a similar tap and situation but the control doesn’t pull out as yours. Still don’t know what to so

Thank you for this video :-)) I can fix our kitchen tap with a bit more confidence :-))

Not sure if same with ceramic cartridges but the older taps would allow you to remove the spline shaft after removing the circlip and winding counter clockwise, found this out by accident on my old bathroom taps one day that had ceased up, removed, some grease and put back together. But i suppose for £4.50 for new ones not worth the hassle.

For lubricating anything plumbing; invest in some marine grease. It lasts way longer and will ensure your taps or moving parts don't cease. Also it will make moving parts smoother to move, preventing wearing of o rings. But good luck on getting it off your hands.

Brit households are always so interesting. The sink is so different than what is typical in the states

Well I simply can’t believe it. My daughter has a shower that doesn’t get hot, I have a window that doesn’t open and a kitchen sink tap that leaks from the top! It’s almost like this is made for me! You couldn’t pop over here and sort them out, there’ll be a beer or 2 in it for you😀

Great job

Of course there is a bottle of IPA in the video!

Would have been interesting to see if you can break apart (disassemble and try to fix) the cartridge.. "Not meant to be taken apart" hasn't stopped us before :D

Back for my 2nd watch (as mine isn't going according to plan lol)...

Once I had to use my pneumatic tyre bolt removing tool to get that cartridge out. Even though the whole sink and tap was brand new and started leaking after 3 weeks but I could not get it out with a spanner.

Hey my mate vince you're a beast

I do not think that the WD-40 lubricant he is using on the o-ring is food grade. At least the Fernox LS-X is listed to be used around potable water.

A great way to remove limescale on chrome fixtures is to get steradent denture cleaner tablets crush them to a powder and then a little water in that to a paste and then splat it on...give it a few minutes and voila, gone...

this is verry difernt keep up the work

I was NOT looking 4 this but U have the same tap as me & mine is leaking from the neck! How random UR vid came up! 🤯👍

Next "upgrade" is changing the aerator, good aerator makes tap to have one neat stream of water not several streams, also unscrew the aerator and check for debris and give it a clean

looks my under sink cupbiard including the big bottle of life saver/IPA haha ts a god send that stuff and i had never herd of it until mmv :D

plz exchange the Jet Concentrator too while your at it and by doing that the splashing will become less too :)

You need to unscrew the cap on the end of the end of the nozzle as it looks like it has calcium build up!

Nice. Saved you a plumber and a new tab and you fixed it yourself.

I think if you tightened the cold water nut on the right a little bit more it would have brand you level with the hot water nozzle on the left.

If you want a good laugh price up those cartridges from the company I used to work for, Lefroy Brooks. Admittedly, the ones we put in our units were the best of the best and not from screwfix, but Jesus they are eye wateringly expensive... Your lever alignment problem was a common one. On some of our units we had a short adapter shaft with a different number of splines on each end. This allowed for fine tuning of the lever position. In your case we would adjust the shoulder of the cartridge to allow it to be screwed in just that little bit more and bring the levers into alignment. When customers are paying more than £450 for a kitchen mixer like yours with a posh name they get really shirty if everything isn't absolutely spot on.

As soon as you lover the pressure in the pipes around a tap, you should always dipp the end of that tap in some cleaning fluid, it screws out and i think that was one of you problem, i do not think that oring on the swan neck was a problem because that hold sutch a low pressure if you have a clean Perlator. At least, that's the name in Swedish. Many watersaving parlators make the old taps leak because it wasn't made to hold a huge amount of pressure, but you have an ardinary strainer that is probably worn and dirty. Thank you for the entertaining video and helping people to realise you can and should fix stuff like this!

Thanks. My local plumber would've charged £2,000 for that lot mate.👍😅😅😅

My two doesn’t even leak… but here I am watching how to fix a leaky tap 😂

More interesting then i thought it was going to be.

thank you

those kinds of cartridges arent really fixable, particularly not that specific leak, scale build up can stop them fully closing but if water is slipping past the shaft then something internal has worn down which you cant really do a whole lot about. some models you can disassemble and find an o ring to replace but these ones dont look to be that kind

What brand and model of sink is this one? Not all tap covers pull out as shown in the video.

Great Job, you really need to work on your ocd with the alignement though vince

Watched your vids for a while mate.. As a plumber surprised at this vid. Not bad job lad 👍. The way ur tap is moving is the rigid washer been fitted under sink?

The cold handle not being upright simply needed a minor tightening of the gland. If he moved it say 1/64 of a turn he would have got it in the precise upright position.

Dude you should get a whole new sink, you totally deserve to have a nice sink haha

The reason the taps is not aligned is one of the valves is tighter than the other

That tap could benefit with an aerator they screw in the end as replacement and will stop that splashy nozzle.

Could prolly just tighten the crooked cartridge a tiny bit more to get it to line up perfectly

Reduce, Reuse, Recycle In that order for most effect!

9:49 "Let me get some spanners" *Pulls out a monkey wrench* Me: 🙄