TS 158 - 2020 Timbersled Setup Part 2 Followup

  Рет қаралды 2,992

jethro450

jethro450

4 жыл бұрын

Snow bike links
BIKE PARTS
CHAIN - Replace your junk timbersled chains with this, will have to cut it - BikeMaster 520 BMXR X-Ring Chain amzn.to/3ACt7Ay
Pivot dolly brace Polaris part number 2208170
Honda GN4 10-40w oil, no engine issue in 30+ years amzn.to/2F8DNLg
SNOWBIKE RAMP (same as timbersled) amzn.to/39oCK7A
FRONT WHEEL KIT Call Jeff @ 661-769-6686, tell him Jethro450 (jed) sent ya
RADIATOR GUARDS - many choices for other bikes, but not YZ450f's www.unabiker.com/
HEADLIGHT Many options, Iceage quite making the one I have, amzn.to/3u2neLB
THERMOSTAT shop.watt-man.com/main.sc
Or C3 stats are awesome c3powersports.com/
TEMPERATURE GAUGE amzn.to/2SAbrxF
Trailtech has adapters www.trailtech.net
3" ALUMINUM TAPE amzn.to/2PXnAyM
AIRPRO FORK BLEEDER www.airprofork.com/
HEAVY FORK SPRINGS Try race tech, mx tech, factory connection, Toby Till @ www.rockymountainsnowmx.com/
FORK SEAL SAVERS - I’ve switched to using full length and don’t run fork guards anymore amzn.to/3KKguYy
TIE-DOWN STRAP HOOKS - handy! amzn.to/2tQD5Q9
HANDGUARDS - Tusk D-Flex amzn.to/33TlSbl
BAR MITTS - Powermadd Gauntlets Bar Mitts amzn.to/2Wu3ONI
ENGINE JACKETS PST is my preferred www.powersportstech.com/pst-en...
Or Selkirk selkirksmx.com/
Or SXS Snow Shields (Engine Jacket) - www.sxslideplate.com/
Or RevvUp revvup.net/engine-covers
Or Drifters Engine Jacket - driftersproducts.com/
FOOT PEGS Fastway Adventure - amzn.to/2tJZdvI
Or C3 has some cool ones c3powersports.com/
Or Flo Adventure Pegs - amzn.to/30dEr3F
ECU - PR2 - pr2racing.com/
Option Buy Vortex ECU, dyno tune it (that’s what I did and it’s amazing, didn't on my 2019) www.vortexcdi.com/
GAS CANS - BIKE IMS for the bike, www.imsproducts.com/
GAS CANS - KIT MOUNTED Mountain Addiction - www.mountainaddiction.com/
Rotopax for the ARO - rotopax.com/
GAS CAN KIT COVERS www.revvup.net/products-old
THE TUGGER amzn.to/38att1B and amzn.to/35UlfsT
POD FILTER PARTS (FOR ’14+ YAMAHA’S)
2 to 2/5” Reducer Silicone Tubing amzn.to/2T5UCjq
2.5" clamp on pod filter, 3"wide by 6" tall - Part Number UP-6245 amzn.to/2H9fleM
3.5"x6" Round Outerwears Cover w/Top Part number 20-1010 amzn.to/2BYhabj
2-3" Hose Clamps (you need 2) amzn.to/3rQDDQr
2" PVC Pipe, go to local hardware store or amzn.to/2VtZLhF
Frogzskin Material For Intake Covers, must super glue amzn.to/2BZhJkT OR amzn.to/2HeK8an OR buy Neil Smart’s YZ intake product (facebook)
1/16" ABS plastic for the front blocker thing amzn.to/309LsCx
1/8” ABS PLASTIC FOR VARIOUS BUILDING amzn.to/2XoclAW
fastfittings.com/ barbed fittings (installing radiator stuff)
CLOTHING & GEAR
GOPRO HELMET MOUNT (best mount there is) amzn.to/2VADDCB
Red Version amzn.to/2GX68XY
GOPRO HERO'S amzn.to/3KNnt2S
GOPRO Tether amzn.to/2Ui0wh2
HELMET LIGHT amzn.to/3fW6vBf or amzn.to/32wSerE
RADIOS
BCA - amzn.to/2HcvRuL
BaoFeng works better amzn.to/2HcbMVc or amzn.to/3nZoLOJ
SHOVEL amzn.to/2EsTsV1
PROBE - many options, amzn.to/3AyytfW
BEACON - DO NOT SKIMP ON A BEACON! amzn.to/3H8X4uj
AIRBAG - DON’T SKIMP amzn.to/2SG83Br
BOOTS - Klim Boa amzn.to/2TbPCK8 (bad for kick start bikes)
HEATED GLOVES - FXR Recon’s amzn.to/3F97qZv
GLOVES Klim Togwotee amzn.to/36LRdsI
BIBS - many options Klim Havoc amzn.to/3o0vgRl
JACKET - Klim Vector Parka very warm! amzn.to/3AxdXwa
HEAD SOCK/LINER - amzn.to/2IO0bOM
PORTABLE POWER PACK TO START BIKE amzn.to/3FZy2MN adapter for it amzn.to/2TtZaik bike battery adapter amzn.to/2u39gw9
509 Heated Goggles - amzn.to/3u2fDge
HJC Universal Breath Box - Black amzn.to/2sArAwf
WATER SEALANT SPRAY - amzn.to/2taPUVr

Пікірлер: 38
@BrodyHenry96
@BrodyHenry96 4 жыл бұрын
Can't wait to see a video of that thing in the steep and deep!!
@jethro450
@jethro450 4 жыл бұрын
Me too!
@CW-up7xv
@CW-up7xv 3 жыл бұрын
Wondering if you figured out the spindle issue?
@jethro450
@jethro450 3 жыл бұрын
Which issue? The fact that the spindle doesn’t fit perfectly and squeezes the forks inward? I left mine shimmed as you see in this video. I did move that front brace to the front holes like I mentioned. Still going strong, not bent. And I’ve hit a few things kinda hard... still good.
@CW-up7xv
@CW-up7xv 3 жыл бұрын
@@jethro450 awesome good to know. Ill do the same thanks!
@SLIVER300WSM
@SLIVER300WSM 4 жыл бұрын
Good video man! I have been taking your tips to get my ARO 137 all set up. I am in Utah as well and am wondering what areas you have been riding this year? Hoping to go out over New Years and would like to find good snow. We usually hit Fairview, but my buddies went there last week on sleds and both got damages. Thanks in advance. TJ
@jethro450
@jethro450 4 жыл бұрын
SLIVER300WSM Nice man! So Logan and Timberlake’s are about the only spots I know of at the moment. Tomorrow’s storm should make everything much better.
@ethermal1
@ethermal1 4 жыл бұрын
Interesting my experience with the riot is exactly opposite what you mention. Literally trenching and getting stuck everywhere. I notice your recommend for the preload is different than brents where he says to go all out on the front preload to 8-7/8, no mention on the rear setting in his video. but I am tempted to undo all the preload on front and rear. So frustrating, haven't had a good ride on this thing yet
@jethro450
@jethro450 4 жыл бұрын
That's too bad. Maybe your track isn't set up flat?? And yes, having the preloads on the springs adjusted could help. I'm really liking my kit, even in the crap bottomless snow conditions it did quite well, I was impressed.
@ethermal1
@ethermal1 4 жыл бұрын
@@jethro450 I rechecked my strut length it does match spec to the hair. Going to be playing with preloads, hope to get it working better
@jethro450
@jethro450 4 жыл бұрын
ethermal1 spec is wrong for my bike. If you’re on a Yamaha, it’s wrong. 11-7/8 is what it needs to be if it’s a Yamaha. Did you watch my episode 158? I went over that and track setup in it. I also have a separate track setup video. Worth a watch.
@jethro450
@jethro450 4 жыл бұрын
ethermal1 Episode 132. Search TS 132 track setup
@ethermal1
@ethermal1 4 жыл бұрын
@@jethro450 I'm on a husky 501, rechecked and reset strut length to 12 1/8. Went out yesterday with the pre loads backed out to 8 7/8 and massive improvement, couldn't get it stuck if I tried. These riots really don't seem to like much if any preload at all
@tradingcurrency1
@tradingcurrency1 2 жыл бұрын
How did you not have to cut your fork guards?
@jethro450
@jethro450 2 жыл бұрын
Heat gun
@SeekTheTruthNow-Freedom
@SeekTheTruthNow-Freedom Жыл бұрын
How did you get the TSS to 400PSI. I'm a similar weight to you and would like to stiffen it up to 400 or maybe even 450 as i find the rear travels a lot when I land off (smallish) jumps. FYI - 2016 MH ST. I think I could only get my shock up to about 250psi - I may have some issues with the pump.
@jethro450
@jethro450 Жыл бұрын
I just keep pumping until the dial goes all the way around and hit the stop. There are newer pumps now that go up to 500 though
@markreuss
@markreuss 4 жыл бұрын
Just wondering if your running the x tune in your tss? Thanks in advance
@larryhawkes1347
@larryhawkes1347 4 жыл бұрын
Jed, how many teeth is the sprocket on the Timbersled that connects to the engine drive sprocket? Im going to do a little ratio math.
@jethro450
@jethro450 4 жыл бұрын
Looks like bike to kit is 13-17 stock, and on the riot kit it's 18-17 (top/bottom). I switched it up to 14-17, 17-18.
@larryhawkes1347
@larryhawkes1347 4 жыл бұрын
Did you get 8 more feet of snow ordered? 😁😁❄️❄️🏔️🏔️❄️❄️😁😁
@jethro450
@jethro450 4 жыл бұрын
Yes, it's coming this weekend! haha
@larryhawkes1347
@larryhawkes1347 4 жыл бұрын
Perfect 👍🏻😁
@dougcook99
@dougcook99 4 жыл бұрын
What battery are you running in your Yamaha?
@jethro450
@jethro450 4 жыл бұрын
Stock. It hasn't failed me yet and I hope it stays that way.
@MitchellHubert
@MitchellHubert 4 жыл бұрын
Do you run a recluse clutch?
@jethro450
@jethro450 4 жыл бұрын
I'm not a fan in general but I wouldn't mind for snow biking so long as it was the one I could do manual clutching as well. I really like my manual clutch.
@philliptoone
@philliptoone 4 жыл бұрын
3:07 It's hard for me to believe that 1/16" thick metal would make any difference.
@jethro450
@jethro450 4 жыл бұрын
Believe it my friend. Believe it.
@philliptoone
@philliptoone 4 жыл бұрын
@@jethro450 When are you going out next? I would really like to go with you sometime with my new KX500. Is there a way I can send you a private message?
@jethro450
@jethro450 4 жыл бұрын
@@philliptoone facebook. sent you a request
@Snowbikebro2
@Snowbikebro2 4 жыл бұрын
be carefull dont hit a stump on one side of the track. bends everything. i didnt hit it very hard. bent both rails and the tunnel plates on both sides.Riot gets a 2 out of 10 in reliability
@Snowbikebro2
@Snowbikebro2 4 жыл бұрын
one suspension rod holding the skid in isnt enough
@jethro450
@jethro450 4 жыл бұрын
@@Snowbikebro2 hmmmmm
@Snowbikebro2
@Snowbikebro2 4 жыл бұрын
@@jethro450 yep my first snowbike with only a few hours on it.
@jethro450
@jethro450 4 жыл бұрын
@@Snowbikebro2 Sounds like an early season injury to me. In all my years (over 10 now) of snow biking, I've never done what you just described... knock on wood! I usually take it pretty easy this time of year, or don't go at all. We're still not there yet, as far as being able to rip it. Sorry to hear this man, that sucks bad.
@Snowbikebro2
@Snowbikebro2 4 жыл бұрын
@@jethro450 I didn't even think it did any damage till I looked at it. Funny thing is the ski hit harder then the rear and the spindle isn't bent.
2021 Timbersled Shootout! RIOT Velocity, RIOT S, ARO 3 & ARO S!
18:08
YZ450FX TimberSled Installation
4:26
SnowTrax TV
Рет қаралды 37 М.
Always be more smart #shorts
00:32
Jin and Hattie
Рет қаралды 42 МЛН
Please be kind🙏
00:34
ISSEI / いっせい
Рет қаралды 190 МЛН
The child was abused by the clown#Short #Officer Rabbit #angel
00:55
兔子警官
Рет қаралды 21 МЛН
CompTIA Network+ Certification Video Course
3:46:51
PowerCert Animated Videos
Рет қаралды 7 МЛН
$60 DOLLAR Paint Job For My Old Truck!  BUDGET makeover Goin' Ta Town Approved?
2:22:49
Integrate REAL Camera Data in Your 3D Scenes!
3:49:41
pwnisher
Рет қаралды 808 М.
TS 157 - 2020 SNOWBIKE SETUP - JETHRO450
16:48
jethro450
Рет қаралды 10 М.
Turbo Snowbike with 122 HP - OMG!
17:52
Vernon Snow MX - The Snowbike Channel
Рет қаралды 71 М.
LEARN OPENCV C++ in 4 HOURS | Including 3x Projects | Computer Vision
3:57:04
Murtaza's Workshop - Robotics and AI
Рет қаралды 2,5 МЛН
2024 Introducing the Gen 2 RIOT 3 - Timbersled
1:08
Timbersled Products
Рет қаралды 13 М.
More power More Better? Revo 2.0 XLX2 8s setup maiden run
4:31
Peter Dirks’ RC Speed Run Channel
Рет қаралды 2,9 М.
2023 Timbersled  Aro3 Gen2 Review & Ride
11:25
jethro450
Рет қаралды 9 М.
I Outsmarted My Bully Brother And Ate His Cotton Candy🤫😎
0:33
Giggle Jiggle
Рет қаралды 9 МЛН
Where are you from?
0:13
ARGEN
Рет қаралды 3,9 МЛН
Когда Нашёл Нового Друга в Диснейленде ❤️
0:18
Глеб Рандалайнен
Рет қаралды 2,1 МЛН
Страшно, когда ругается мама😰
0:10
Лиза Вертинская
Рет қаралды 2,6 МЛН