TT-01 Carbon-Aluminium Project EP3: Build Vlog 02 - Soldering, Finishing Touches & Test Drive

Рет қаралды 4,843

Күн бұрын

This is the final build video: soldering, installing electronics ,gluing tyres, drilling body and test drive.
Parts List: Chassis bit.ly/3NYVnmj
Body bit.ly/3QlZoTZ
Motor & ESC
Brushed Combo bit.ly/3aNMXzQ
Brushless Sensorless Combo bit.ly/3mIx5l0
My Setup - Brushless Sensored bit.ly/3xI19Dq
My Setup - 120A Sensored ESC bit.ly/3zCpdZM
Motor Pinion www.corally.com/Pinions-Gears...
Or just buy Tamiya gears.
23T is the smallest you can use safely. 21T might work if your motor can is not bulky.
Servo, option 1 JX PDI-4409MG bit.ly/2x73Fqz
Servo, option 2 SPT 4412LV bit.ly/3xHhXue
Category: buy once, use forever
Transmitter Radiolink RC4GS V3 bit.ly/3twII26
Transmitter Flysky G7P bit.ly/3Pwjn1z
Transmitter DumboRC X4 (Budget Option) bit.ly/3zyZHEE
Charger SkyRC S65 AC bit.ly/3xnCin8
Charger iMax B6 (Budget Option) bit.ly/3xI1ZQA
Tools
Hex Driver bit.ly/3zDTAzf
Hex Socket, Nut Driver bit.ly/3QinvCD
Reamer bit.ly/3aX6iPi
For battery, shock oil, screws check your local store.
Time Stamps
Planning & Preparation 00:00
Soldering 04:40
Testing servo with new ESC 06:12
Putting ESC on the chassis 06:53
Installing servo 09:07
Setting up transmitter 11:19
Drilling the body 15:31
Gluing the tyres 17:26
Front toe setup 19:49
Installing bumpers 21:00
Test drive 21:27

Пікірлер: 15

@JakeDogg-RIP 2 жыл бұрын

Good boy beaver frend! 🥰🐶

@ianhill20101 2 жыл бұрын

Roof top race track, nice area looks lovely.

@EidstaRC 2 жыл бұрын

You’re gonna need some proper rubber race tires. I started with the cheap eBay/amazon stuff. Then I never looked back when I started using race tires that are temp matches. I really like sweep or rush racing. For track surface temp 70-100F i use 36 deg tire. 100+F I use 40 deg tire. I love 1/10 touring.

@nc6055 2 жыл бұрын

How can you make a wltoys k989 94mm wheelbase

@yeraytrdsur Жыл бұрын

Hello,any avance in your setup?

@BeaversHobby Жыл бұрын

I've got the help from local club to set it up. Basically for touring in general is front spool or in this case locked diff. Open it up and glue the gears inside is enough. Rear diff setup is with medium to high resistance. It's with oil no.20000 on my track, yours might be different. Hard spring on both front and rear. 1deg front toe out. 5mm front ride height and 5.2mm rear. Again, toe and ride height differ from track to track.

@erivera989 2 жыл бұрын

Which soldering iron are you using. It seems really light and easy to manage around small projects.

@BeaversHobby 2 жыл бұрын

Sequre SQ-01 bit.ly/3D8hAKa Here's my review kzfaq.info/get/bejne/frWTm9KCr5fHmpc.html Basically it's the TS100 from another manufacture. It's really good and you can power it with lipo when you are outdoor as well.

@erivera989 2 жыл бұрын

@@BeaversHobby Awesome! Thank you for the information. Great video as usual, thank you for the content!

@exemch4826 2 жыл бұрын

Is there any way to estimate top speed of a 9500kv k696 with 17t pinion and 25 tooth spur gear?

@BeaversHobby 2 жыл бұрын

KV means RPM per volt so you can multiply that by 8.4 (fully charged 2S lipo) and then multiply that with final drive ratio to get the RPM of the wheel. After that multiply it by the wheel circumference and you will get the speed in mm/minute if you measure the wheel by mm. So it's around 76KPH theoretical top speed.

@exemch4826 2 жыл бұрын

@@BeaversHobby where can i find a larger pinion gear? Or a smaller spur gear. For the surpass hobby 1410 would the shaft be 2mm?

@BeaversHobby 2 жыл бұрын

@@exemch4826 Banggood, ebay or aliexpress. It's just a standard plastic gear mod 0.5 pitch so you can find it pretty easily. And yes, the shaft is 2mm.

@exemch4826 2 жыл бұрын

@@BeaversHobby is the spur gear on the driveshaft have the same 2mm diameter or is it different? And would you recomend gaining top speed by changing pinion or spur gear? Is there an advantage one way or another? Also, Got it working today and after fixing some broken parts and also am finding that my suspension is rubbing the ground, is there a way to fix that? Sorry to ask so many questions btw, thanks

@BeaversHobby 2 жыл бұрын

@@exemch4826 The spur slot is around 3mm and it goes into the rear gear so, different way to insert it. Both ways result to the same thing but adjusting the pinion is easier and has more choices.