TTL Electric Skateboard Lights Review - Interactive Intelligent Esk8 Lights

Рет қаралды 6,208

Күн бұрын

You can buy it here: solidcircuits.net/shop/
The TTL light kit has been such a fun product to review. Though the kit took some tinkering to set up, the final results look amazing. If you are looking for interactive lights for your DIY Electric Skateboard and price is not an issue then this kit is a great option!
More Information:
Regarding UART Remotes:
- Using a dual ESC that has two UART ports you can use a UART remote
- A uSplit could be used if you only have 1 UART port and are using a remote that allows PPM throttle, but uses UART to get ESC data
TTL Firmware:
- The TTL module firmware can be updated through the app. The firmware is continually upgraded by Solid Circuits as improvements arise.
- Support for ADC based throttle input means that eScooters can use the kit.
Headlight Design:
- The TTL headlights use oval lenses that cast it more to the sides. This gives better visibility to the directions you will be carving into, and keeps the light down and out of the eyes of people you pass.
- The TTL headlights use a "Neutral" color temperature.
Taillight Design:
- The red cover is designed to diffuse the light into itself and make a bright glowing point of light that can be seen from far away in many directions.
Here is our website: propulsionboards.com/
Buy Merch: propulsionboards.com/collecti...
Support us on Patreon: / diyesk8builders
Check out our parts list to our boards: electric-skateboard-parts.mys...
Follow our Instagram @diyesk8builders
0:00 Introduction
0:56 Unboxing
3:58 Components Used
5:01 Set Up
9:31 Finished Look
10:09 Review
15:24 Conclusion

Пікірлер: 23

@solidcircuits 2 жыл бұрын

Thanks for the honest review and for doing a great job at showing all the aspects/options of the kit! Its very much appreciated!

@DIYesk8Builders 2 жыл бұрын

Thank you for sending this to us for review! Such a cool and innovative product!

@jayveeSM9 2 жыл бұрын

the circuitry and electronics is well designed, however as the front and tail lights protrude in front and back of the deck, i believe this will be more prone to damage due to bashing either front or back of your board. If you can redesign this to be not protruding, i think this would be perfect and prevent damage to the lights

@EREBUSAETHER Жыл бұрын

That's actually pretty cool, outside of the colors it's still useful

@hermannn1874 2 жыл бұрын

absolutely love ur content keep aup the good work

@IAM-iv1oz Жыл бұрын

Oh wow! I Have been searching for gear like this for years! Thank you so so much for doing and delivering this excellent video. New Sub and follower bro. Peace.

@DIYesk8Builders Жыл бұрын

Thank you! We are glad to hear that you enjoyed the video.

@krishnansrinivasan830 2 жыл бұрын

a fun project :)

@ratheonhudson3311 2 жыл бұрын

What a fantastic kit! Thanks for the rundown. I run with both a 36v 40ah and 12v 50ah lipo block pair on my heavy board so I'd like to know if these can be run off 12v alone?

@solidcircuits 2 жыл бұрын

Thanks for your support and question. There are two control module options to support different power source options. The SP version (used in the video) is powered directly from a 6S-12S battery, while the EP version is powered by a 12V source of the users choosing.

@eBoard3R 2 жыл бұрын

⚡👀⚡ 🤙🏼🤙🏼🤙🏼

@davidcarbon9771 Жыл бұрын

very cool product. you should post this to r/electricskateboarding

@DIYesk8Builders Жыл бұрын

Thanks!

@TheAETHER22 2 жыл бұрын

I wish somebody would develop a led controller with integrated battery or connectable to external powerbanks and gyro controls for brake detection etc. Some of us have a carbon unibody with zero extra space and impossible to drill holes because of structural integrity to connect anything with escs and batteries.

@Supreem6969 10 ай бұрын

awesome video i wonder can i put this on my HiBoy E scooter?

@DIYesk8Builders 10 ай бұрын

It may be possible but would be difficult

@IAM-iv1oz Жыл бұрын

Will this work with the POSSWAY T3? Any idea bro?

@DIYesk8Builders Жыл бұрын

Would be pretty difficult I think. This is more made for DIY. Might be possible though

@VeganDefinition Жыл бұрын

What's the difference between analog and digital as far as looks? I bought analog because digital wasn't in stock.

@DIYesk8Builders Жыл бұрын

Digital can do more complex light patterns than analog. Analog lights will all be the same color at a given instance

@VeganDefinition Жыл бұрын

@@DIYesk8Builders Thanks, I've found this out since then it was kinda a let down but hopefully looks good none the less.

@colinbiddle2649 2 жыл бұрын

If only it was not 3D printed. I feel as if it would break if something went wrong while riding…

@solidcircuits 2 жыл бұрын

I definitely understand your concern. That is why if any 3D printed part is to break on a user, the part will be replaced at cost of shipping. The 3D printed parts have gone through numerous iterations to make sure they are as strong as can be while staying low profile. So far, they have been used by beta testers and customers for hundreds of miles on various terrains and no problems have been reported.