So glad they decided to do the rear tire, which is always easier than the front. And they don't bother showing the way you struggle at the end with the front tire and how to get around those struggles.

I had some older dented up rims and was worried that it wasn't going to work, but it has worked PERFECTLY for 2 years now!!! I found out that it seals to the tire, NOT the rim, so as long as you have fresh tires, you are good to go! And the system has protected my rims AMAZINGLY since then. And once I followed the instructions I had no problem with install. THIS VIDEO WAS VERY HELPFULL!

Holy crap!! I think I'd rather do my taxes twice a week than to install another tubeless system, I can definitely understand why she took the sprocket and rotor off first! WOW

This always my go to vid. when I do a tubliss install. She does a perfect job of explaining the process and she has cool tattoos!

Awesome video. Thanks for the tips. I'll admit that I worked a little harder than the lady in this video but next time around I'll have it down.

I'm always amazed at how easy the tires go on in these videos. Tire warm, soaked with RuGlid bead lube, bead down in the drop center, everything by the book (video), and it still feels like I'm about to break the bead getting the last 8-10 inches of the tire over the rim. I never pinch the tube and always get the tire on there, but it's a wrestling match, nothing like what's shown in all tire mounting videos.

I keep coming back to this video. On my 4th front and rear tire changes, but I just can't remember the sequence to demount and remount each time.😄 But I completely skip beyond soapy water and go full nuclear. I add 6-8 ounces of tire Slime sealant before installing the second side of the bead. I keep the tire horizontal while installing the second bead. Then I bounce it where a slime leak won't matter (garage). Then pressure as usual. The slime always ALWAYS works and makes a perfect bead seal. I never lose air from the low pressure side. Running anywhere from 10-6 psi in the rear and 10-8 psi in the front. No flats in almost 5 years and have not had to replace any Tubliss component yet.

OMG. This is not my first tubeless and this video makes it so easy it’s not 50% like this

Looks like the inner bladder is restricted when going past the bead lock? Is this correct and problems with it when installing it? Thanks

Thank you for the information. 🇺🇲🤙🏼

What brand of tire tools are you using?

WHAT TIRE SPOONS ARE YOU USING?

Does it work with big bikes like ktm 990 adventure???

What is the stem removal tool used here? I need to get one. I have a few but this one rocks!

That must be a soft display only tire. No way is it that easy. I understand the video is to get the point across how. I’ve done a few with this system and it’s takes some time.

I'm thinking she's putting a 19 on an 18 inch rim, makes it look way to easy !

I cant find the original tape online is there really a need for it? Or is normal ductape also ok?

So the water stays in tire? Wouldn't that make the tires feel like they're off balance and shake when going fast with all that water swishing around in there?

Armourall spray which one do I buy?

Excellent instruction, thank you!

Will they ever make a 16 inch version ?

Does anybody have trouble with a slow leak from the low pressure (actual tire) chamber, coming from the high pressure valve stem? I had that on my rear and then did the "soapy water and bounce on the ground trick" and that worked but then on my front tire I just can't get it to stop leaking. It seems like the nut that's on the high pressure tube should be on the outside, how is it supposed to seal with that huge nut in there? I mean it worked on my rear tire but the front is still not working. Any other things to try before taking it off and starting over?

the best of the best

First time installer, although I used a no mar to hold the tire in place and I’ve installed plenty of conventional tires. had no problems installing my Tubliss system. And it was not warm, about 58 degrees in the Garage. I don’t understand what all the complaining is about.

I rode my tubliss with a flat rear tire and the tube wore through the red outer part and was down to the cords. It's destroyed.

Definitely a 19" tire on an 18" wheel...

So just fitted my first tubliss system. Absolutely piece of piss. 40 minutes all in. only used 2 levers and some silicone jizz. no skinned knuckles and very minor swearing Will defo be getting one for the front when my mousse gives out.

Hello!can you please tell me if the tubliss must remain inflated over the winter if i don t ride the bike?thanks!

Could I install a Bib mousse and this at the same time to get both there advantages?

So I just bought two of these Gen 2 versions and after watching the video and it insisting on NOT OVERLAPPING the tape ends, I take out the instructions that wrapped inside with the tape and they say to overlap the ends by a minimum of 1". So what gives? Which is it?

can this tubliss use for longevity? long long highway on road?

Great video really helpful 👍

Does the kit include nail polish?

So you need armour all and soapy water? Finish at the rim lock if she tells you to dopey. Where's the updated rim tape vid?

what if it leaks where the valve stem comes through the rim?

easier to mount and dismount these than a regular tube, especially a 19" when using a high breed cheater tire

I fighted with the last piece and the key was to spray some soapy water inside. Also i used BabyPowder for all inside. Its dry and slippery but without a little bit wet slippey lubrificant...NO Way 😅

I'd like see her take off a front 90-90 tyre and put a new one on a rim with a tubliss system, its a nightmare! I end up carefully cutting the old tyre with an angle grinder with a cutting disc, not ideal by any stretch of the imagination. The problem is that there is just not enough space in the rim 'well' for the tubliss system and the tyre.

You've done that before!

Az első kerékkel mutasd meg ne a hátsóval!

Help me! Soapy water ia Just normal dish Washing fluid with water or something we have to buy?

What part of this is tubeless?

Why don't you put up a newer video showing the new tape and do the much more difficult KTM front with Maxxis M7324 front, 90/90-21 = IMPOSSIBLE

No chance to get this mounted on an 2.5" DID rim. Tubliss prevents to get the tire into the middle of the rim, once one side is mounted. Must be a nightmare to fix abroad and on the trail. Nevertheless a nice experience to have a scratched rim and buying a system and throwing it in the bin after zero miles.

Nice instructin. My Remark, please consider, not everybody is an native english speaker. If you would speak a bit slower, it would be much easier to understand you.

Your video instructions contradicts the paper instructions not supplement them. Only add to confusion! Simple example is you say not to over lap the tape and only use one wrap in the middle where the instruction states 3 wraps are needed one middle and one on each side...

Why do you put Adsense and adverts on a product guide I paid you money for. Extremely frustrating.

What a pitfa give me a traditional tube

This video and the supplied instructions tape the rim completely different

Ваши камеры тюблиса за последнее время стали полным дерьмом! Рвутся постоянно! Сделайте что то с этим! Мне очень нравится система тюблиса, но эти камеры меня выводят из себя!(

That is waaaaaay too much work and modifications… Just go true tubeless. Or carry extra tubes. This is unnecessarily expensive and complex. Looks like it requires maintenance and upkeep as well.

WARNING - this is the INCORRECT way to put on the tape. Disgusted with TUBLISSMOTO for leaving this up.

The video is pure bull. the install borders on impossible, you will never get the tire into the drop center, it is physically impossible with the other tubliss junk you've already stuffed in there. I have destroyed my front rim and two tubliss bladders trying this. Going back to a regular tube, this garbage is a waste of time and money!

How do I become cool and get tattoos all over my body along with hepatitis and no job?

By the far worst idea ive ever seen implemented onto a motorcycle.