Tutorial: How to crimp connectors, strip wire and use heat shrink.

Рет қаралды 2,418,585

11 жыл бұрын

Visit my website for more Tips, Videos, DIY projects and more:
www.mjlorton.com/
----------------------------Click "Show more"--------------------------------------
A guide on using the correct tools to crimp connectors, strip wire and apply heat shrink.
Please support my content creation by using my Amazon Store:
astore.amazon.com/m0711-20
Buy these tools and connectors here: astore.amazon.com/m0711-20?nod...
-------------------- Click "Show more" ------------------------------
My website and forum:- www.mjlorton.com
Donations and contributions:- www.mjlorton.com
My techie channel MJLorton - Solar Power and Electronic Measurement Equipment - / mjlorton
My Techie Amazon Store: astore.amazon.com/m0711-20
My other channel VBlogMag - For almost any topic under the sun! - / vblogmag
My VBlogMag Amazon Store: astore.amazon.com/vblogmag-20
-----------------------------------------------------------------------
=================================================
Video sponsor, Pass Ltd - their websites:
www.tester.co.uk/?cmid=QmhzQjc... - Test Equipment and Test-meter suppliers and
www.calibrate.co.uk/?cmid=Qmhz... - Calibration and service of test equipment
=================================================
Further discussion and link to NASA guide here:
mjlorton.com/forum/index.php?t...
In this video:
* Selecting the correct wire gauge (AWG - American Wire Gauge) for the crimp connector.
* Using the correct tools to strip the insulation from the wire.
* The correct way to insert the wire into the crimp connector
* Using the correct crimp tools to crimp the connector
* How to apply heat shrink correctly to the wire and crimp connector.

Пікірлер: 915

@thomasfinley4199 2 жыл бұрын

The best explanation I have ever read: well-organized, planned, and delivered. Plenty of cautions, pro and con advice for the novice. Thank you MJ Lorton!

@watchvideo7225 8 ай бұрын

Are you muting it and then reading the subtitles or what? :D

@evahle 3 жыл бұрын

It's not very often that I enjoy a 30 min. video all the way through, but this video was exceptional. Thank you!

@modemlaugh 2 жыл бұрын

I didn't realize how much I did not know about using proper tools and technique for crimping wire connectors until watching this video. Thank you!

@CCobraProductions 3 жыл бұрын

This video presentation is easily the best instruction video on how to properly crimp cables and wires. Nothing else comes close. Excellent presentation!

@hatchetman29 4 жыл бұрын

I know this video was posted a long time ago but it’s still one of the best. Quick contribution: if you’re using colored shrink tubing to mark a cable (discussed at 18:17) but still want to be able to see the crimp, shrink the colored tubing around the outer jacket up to the strip point. Then crimp and pull up a second piece of transparent tubing to overlap the first and cover the connector. It’s not much of a tip but... for what it’s worth.

@sharadpatel5143 3 жыл бұрын

Top quality video in terms of explanation, every small details, technical tips and reasoning, great clear voice . Compliments !!

@BoydWaters 4 жыл бұрын

Many thanks. I made some ugly wire connections, then came here. Your patience helps me, carefully walking through all the bits I bodged up!

@saulzeigen1348 6 жыл бұрын

Lots and lots of videos on crimping, yours is the only one that's worth watching. Thanks for posting. Regards from Colombia!

@nothankyou5524 3 ай бұрын

This is a great video. Are you still an a$$ kisse

@djbaasje 3 жыл бұрын

what a bunch of nice people in the comment section for once. Thank you for this informative low pase well explained tutorial. This is timeless and you deserve all the credits for sharing this with us.

@RockerMtl1 2 жыл бұрын

Very well made and explained video on an important issue I see being done wrongly by professionals …. Thank you for the video!

@SCOUSERONTOUR11 9 жыл бұрын

I never, ever, ever thought I would ever need to watch a video about crimping; life is too short! However, here I am having to make up a set of 16mm battery cables for my caravan (I also never, ever, ever thought I would own a caravan!). Well presented, informative video; thanks for sharing!

@mikeb6198 2 жыл бұрын

One of the best videos I have followed in last 2 years. Really on the mark and very easy to understand and see the technique. Thank you for sharing this. 73

@E5Bobby 10 жыл бұрын

Incredibliy thorough! Very impressive. I've used just about every connector you show and I have most of the tools you show as well. But even with my experience I couldn't have explained it as thoroughly as you did. Well done! I too used to solder some crimp connectors (after crimping) but I read below that that can actually worsen the connection/connector. I didn't know that. I do that because I've seen too many crimp connectors (in automotive use) fail due to corrosion. But the comments made by "Executive" below enlightened me. Up until now I would never have guessed that a crimp connection could be better than a soldered connection. Still, I would say it depends upon the application and how carefully it is soldered. Mostly what I want to say is "EXCELLENT VIDEO"! When I started I thought "I can't sit through 31+ minutes of something I already know" but now I'm very glad that I did!

@jimandersen6638 Жыл бұрын

Great video. A couple suggestion. It wasn't clear that there are different crimpers for insulated vs non-insulated connectors. In addition, the crimp (indentation) should be made on the side away from the seam of the connector.

@bobrusso1814 2 жыл бұрын

Very good presentation. May I suggest two modifications. 1. We always use a bit of no-ox inside the ferrule and on the wire strands to prevent any future oxidation or dis-simular metal corrosion. 2. The crimp dimple should be put on the side of the ferrule without the seam. Our inspectors look for a bit of wire and some evidence of the No-Ox through the witness hole. Love the clear heat shrink usage, the only way to go. Many Thanks.

@markharrisllb 3 жыл бұрын

I’ve never used a connector in my 60 years, but I certainly feel confident enough to approach this aspect of my small small projects now. A brilliantly comprehensive tutorial, thank you.

@aajaanron 2 жыл бұрын

Thank you for doing this; a very easy-paced, clearly explained and thoroughly demonstrated tutorial. So much so that it is still accurate and complete 8 years later.👍👍

@turtleman190 2 жыл бұрын

I really do miss the good old youtube tutorials like this

@awaisali7115 7 жыл бұрын

Strange , the man took half hour to explain everything in detail without making any mistakes but still 222 dislikes from those who think that the video has many mistakes .People never appreciate effort and time that the video maker spend for us and dislikes the video over small matters , shame on those who disliked the video and discouraged the maker to teach us , shame on enemies of knowledge ,

@2k3r11s 5 жыл бұрын

+Name Name - Mass, Length, and Time are the three fundamental mechanical units from which all other mechanical units are derived. Everywhere that he refers to the fit of wire in the connector, he is referring to the dimensions of those objects (fundamental mechanical unit: length). Mechanical units & properties are one of the many subsets of all of the physical units, with other sub-categories including electrical, optical, thermal, chemical, etc. A conversation regarding whether or not a connector "electrically" fits the wire would be an entirely separate discussion from whether it "mechanically" fits the wire, but both of these discussions would be in the realm of whether or not it "physically" fits the wire. "Mechanically" was certainly the correct term for him to use. "Physically", while also correct, is significantly less specific.

@erkful 5 жыл бұрын

phuck ewe lol british accent...guess you dont get out much

@2k3r11s 5 жыл бұрын

@phuck ewe He meant that it's obviously not British, it's South African.

@dv2915 5 жыл бұрын

The maker of this video discloses some essential secrets of the trade to the wider public. It is not difficult to see why someone might not like that.

@2k3r11s 5 жыл бұрын

@@dv2915 Like it or not, that's the whole point of KZfaq. Putting a dislike on a KZfaq video for that reason is quite counterproductive, you're only helping KZfaq grow.

@sweetmemories4448 2 жыл бұрын

Thanks for a wonderful video. I had used a hair dryer to heat the heat shrink in the past while connecting a cable to a fuel pump and it worked. Those days I never heard of a hot air gun that is shown towards the end of this video. Well done providing useful tips.

@g.pollyjordan8438 Жыл бұрын

I have been looking everywhere for this level of detail and explanation. I am an old woman just getting interested in solar with no experience with electricity and I want to learn. This type of presentation is beyond spectacular. I don't see it listed on any of your playlists but I would like to see more of this basic level of information with all the detail you have provided in this video. You are a phenomenal teacher. How can I start from below ground zero to learn all about electricity and wiring for off grid living? Thank you, Thank you, Thank you.

@garybaris139 9 жыл бұрын

I much prefer using the hexagonal crimper for the bigger lugs and have used them often on up to 300mm square where you'd use a hydraulic crimper. One thing I feel I must mention is that as far as I'm concerned, you have a bit too much heat shrink on the 10mm square lug as you always want to keep the foot of the lug clear. Should you want to bolt that lug to a flat surface or a copper bar, you would have a inferior connection due to the heat shrink encroaching onto the foot of the lug and thus ending up sandwiched between the two conductive surfaces. The foot of the lug is sized so as to properly conduct the rated full load amperage of the cable through the area of the foot of the lug. I also like keeping the inspection window clear. Apart from the above, it is a superb video covering most all of the essentials of doing it right. Thank you :-)

@gmoose777 4 жыл бұрын

true but if that is an issue the heatshrink can be trimmed easily with an exacto blade or stanley knife so hardly an issue

@Good-Enuff-Garage 9 жыл бұрын

The Best Crimping / Wiring Video on KZfaq, thank you so much!

@dowecedolo5171 5 жыл бұрын

you make good teacher good one

@hectorechavarria4501 3 жыл бұрын

I have never done any cramping before, or anything electrical related. Without this video I would’ve made some very amateur mistakes. Thank you so much for this.

@lindaparker6980 9 жыл бұрын

Thank you so much for the detail instructions. My first time attempting to fix the wire that connects to the lawn mower battery, which had broken off at the connecting place. I don't know what all you call that stuff, but I did fix it, and charged my battery and mowed my back yard! It worked, even if I didn't have the exact tools to do it the way you showed. Yea! Now I won't have to wait to get a man to do it! Thank you, thank you, and thank you.

@eddraper 10 жыл бұрын

This is one of the best videos you've done. I've made that soldering mistake before and a number of others you mention. This was very helpful...

@h.sapienstechnologicus8865 3 жыл бұрын

Legend has it MJLORTON has so many meters, God came by to borrow some when he was inventing electricity

@TicketyBoo. 4 жыл бұрын

There are loads of videos on this subject but yours is by far the best presented, very useful - thank you.

@lingfromhongkong 2 жыл бұрын

excellent and clear video teaching how to properly crimp and what pitfalls to avoid! thank you so much!

@janestewart3231 4 жыл бұрын

For a newbie to this, I found your video extremely helpful... giving suggestions what to and not to do. Thanks!

@salttram1 10 жыл бұрын

Thank you for your tutorial and well-thought-out steps. I feel sufficiently schooled for my overland solar/dual battery/accessory install. It's entirely possible that your video will save lives, if it hasn't already. Thanks again . . . you are a gifted teacher.

@dave4505 Жыл бұрын

Nice easy to learn instructions. So many people overexsplain themselves but you did a great job.

@nothankyou5524 3 ай бұрын

From 10 years into the fiture, nicely done. Very nicely done.

@PlayinBanjo 8 жыл бұрын

Excellent video! easy to follow, detailed just right, clearly shows the right way to join wires and gives the rationale for the way you did it (often overlooked in instructional videos). thank you!

@ponkkaa 9 жыл бұрын

Very well thought out video. I didnt know about correct orientation of the connector in the crimping tool. Thanx for posting this.

@thanhheu4129 4 ай бұрын

Thank you, this is informative and straightforward tutorial for crimping and using heat shrink 😃

@finallyitsed2191 4 жыл бұрын

I've done complete wiring harnesses for cars and thought back on how many errors I made after watching this. Who among us hasn't twisted a connector on to the wrong gauge wire? LOL. Very informative and well done video. Thank you.

@jamesnicklas2596 3 жыл бұрын

I've found rotating the connector in a common direction while inserting it on the bare copper keeps the strands tight and prevents strands from coming loose.

@shvideo1 3 жыл бұрын

Very nicely explained with all the pitfalls covered. Thank you for sharing your skills and for your thoroughness. I always wanted to learn how to crimp properly. It is a very practical skill to have.

@user-bx6vu Жыл бұрын

Hands down the best video on the topic. I needed this info to learn how to correctly connect a ham radio to a power supply. The part about the current rating was particularly helpful and the one about not tinning the stranded wire. Very helpful indeed!

@IDontTalkToCops 6 жыл бұрын

Thank you for taking the time to create this content. Very helpful and well explained. Cheers!

@pappabob29 9 жыл бұрын

Very well done and thorough video. The one thing I would point out, that was NOT included, is regarding properly choosing the size of your shrink tube since it also must be sized properly. I believe most of it shrinks to about 50% of it's initial size. That may not be universal, however. Again, thanks for a very informative video.

@mjlorton 9 жыл бұрын

Pappa Bob Thanks for the information and feedback.

@drampadreg1386 7 жыл бұрын

I buy both 2:1 and 3:1 heat shrink for different jobs, the 3:1 is great for smaller gauge wires like speaker cables etc but tends to tear later if you don't shrink it completely and it gets hot later causing conductive things to pop out so make sure you shrink it all the way when you install it.

@foxyrollouts 7 жыл бұрын

got some really nice crimpers

@foxyrollouts 7 жыл бұрын

really sux havin to strain

@Goodmorningroosterlive 7 жыл бұрын

put both handles into the vice and spin :D

@LynxStarAuto 10 жыл бұрын

I'm glad you made the point of how crimping can actually provide a more efficient connection than soldering...

@paulweston8184 3 жыл бұрын

Why? Did somebody make fun of you for crimping?

@longboardsenior8824 4 жыл бұрын

Great video for the electronic novice like me to understand the proper way to crimp proper connections. Thank you!

@binhminh417 5 жыл бұрын

IMO, this is the best tutorial of how to crimp connectors on KZfaq. Thank you!

@Pavement-Prophets 10 жыл бұрын

Very informative, really embraces the spirit of KZfaq. Stuff the detractors, you've done a great job mate, thanks, already bought the tools and can't wait to get started.

@mjlorton 10 жыл бұрын

Thanks for the post Andy, appreciated.

@tyebo2010 Жыл бұрын

reading through comments and I haven't come across a detractor yet!

@xan778 10 жыл бұрын

Great video, exactly what I needed to know. Very in depth and informative!

@mjlorton 10 жыл бұрын

Thanks for the post!

@sherryannknowles5423 10 жыл бұрын

I know I'm A little simple or a dits but I have been having problems with crimping to the point of youtube and your video.. You have done a great job here and I have learned a lot and now I don't feel so ditsey. Thanks Lee

@justwelltariang2456 2 жыл бұрын

Sir, what you have taught I think comes from years of experience. It gives me immense pleasure and a very good tutorial. Awesome.

@QuantumBraced 9 жыл бұрын

An excellent tutorial as always, thank you.

@runinguy 8 жыл бұрын

This information was helpful, thanks.

@LYC54 10 ай бұрын

Best instructional video ever. Thanks so much Mate. You deserve a cuppa and a bisquit after that excellent video!

@CheiithooCat 5 жыл бұрын

Great explanation. Whoever can learn but not whoever can teach. And you do both great. Great teacher.

@jorgewashington2981 8 жыл бұрын

Very informative as always. Thanks.

@kostaskritsilas2681 4 жыл бұрын

This is a really good video, it covers a lot of areas well. It would have been good to elaborate on why crimped connections are more "efficient" than solder connections (mechanical strength, better able to withstand vibration (solder can crack under mechanical stress or vibration)). It would also have been a good idea to note that the crimping tools for insulated crimp terminals ARE NOT the same as the tools for uninsulated crimp terminals.

@Inspironator 9 жыл бұрын

Sir, you truly are an expert in this topic. It is a shame that others on KZfaq give instruction on poor methods of crimping connectors. Keep on YouTubing and Cheers!

@joem6859 3 жыл бұрын

easily one of the better videos on crimping connectors, nice close-ups, good details, nice presentation, do's and don'ts and why's.

@obfuscated3090 8 жыл бұрын

Instead of the usual "auto store" plastic-sleeved splices and lugs you can do as the pros do and use naked crimp connectors then heat shrink over them. I buy in bulk off Ebay and store my terminals and splices in clear plastic fishing tackle boxes for convenience. Naked connectors cost less too and take up far less storage space. Have fun!

@obfuscated3090 2 жыл бұрын

@Vyacheslav Every aircraft avionics tech to begin with (I was one fixing fighters for Uncle Sam and am also an AMT) because crimps were found to be less brittle than soldered pins and splices while heat shrink excludes moisture which creates high resistance due to corrosion. That's why bulk bare connectors exist along with adhesive-lined polyolefin heat shrink tubing (available at any industrial supply). Crimps will do in highly protected environments (industry inside electrical boxes) but for anything subject to moisture and flex and/or where the bulk of say crimp splicing a cable repair is an issue crimp and heat shrink get the nod and they're an upgrade elsewhere. Unlike cheap "press fit" connectors, modern connectors are supplied like these examples with precut heat shrink sleeves which being transparent permit inspection of the joint. Opaque cheap auto store style splices block visual inspection leaving one to guess by the condition of exposed wire strands. kzfaq.info/get/bejne/d9h_e8Z7mcimoYE.html Non-aviation example: kzfaq.info/get/bejne/f8eRm8170pq1c6M.html Cheap connectors have their place but the other options (which are a bit more work) aren't used in more demanding applications without reason.

@ElRazTheGreat1 9 жыл бұрын

Nice detail on the how to, I almost always add solder to my crimps to make a good connection too, thank for sharing! Godspeed, Raz

@mjlorton 9 жыл бұрын

ElRazTheGreat1 Thanks for the feedback Raz.

@waswestkan 7 жыл бұрын

Motor vehicle and trailers where I most use stranded wire and crimped on connector. I never sold them any more. My experience is that wire in time will fail at the point where the solder wicked back under the insulation due to work hardening. The purpose of solder where connection is both electrically and mechanically secure is to protect it from the environment. That can be done with the proper application of * quality* electrical tape

@OldSchoolHacker 5 жыл бұрын

Excellent video. Great tips especially the one about the tinning of the wire before crimping. I appreciate your thorough treatment of the subject.

@theelmonk 2 жыл бұрын

Thanks for that detail about which end of the crimp goes into the differently-shaped jaws. Always wondered which way round that should be.

@petermartin3385 7 жыл бұрын

As a complete novice - thank you - I now feel I can deal with this. I particularly appreciated the way you highlighted possible faults/ errors -- which I am sure I would've done. Again thank you -- well done.

@neil4374 7 жыл бұрын

A great video for us novices. Many thanks. I feel I know enough to crimp connectors and heat shrink properly.

@Steve-pu4zx 5 жыл бұрын

no do not use this video to crimp wires

@edwardhugus2772 5 жыл бұрын

@@Steve-pu4zx I would never use a video to strip and crimp wires, I think I would use the proper tools for the job.

@Steve-pu4zx 5 жыл бұрын

@@edwardhugus2772 you should be a comedian.

@tomb375 5 жыл бұрын

EXCELLENT DETAIL! Thank you for all your great videos.

@assertivekarma1909 3 жыл бұрын

I've seen newer videos of yours, this is obviously older, but A+ quality!

@MrFreddiew1 9 жыл бұрын

Look up/Google " Large Crimp Validation Poster " . Very helpful wall chart. Explains the importance of a gas tight seal on a crimped connection. I used to be an Application Tooling Product Manager with Tyco in Germany/Bensheim. Take it from me, only use correctly sized wire for terminals and the correct crimp tooling. All Tyco tools are specified for specific tyco connectors. Crimp tooling from China is unreliable mechanically and crimp specification wise. Crimpimg RGB fastons or ring terminals for automotive use....Use the correct tool to get a long lasting air/gas tight connection.

@shockingguy 4 жыл бұрын

MrFreddiew1 Absolutely, most people have never heard that term, gas tight. Well I might make another comment about that term but ha ha I’ll be PC here. Once you explain that term to people like using a 66 block connector for a insulation displacing connection of a phone wire then sometimes the lightbulb goes off and people understand.

@marcelolopes1347 11 жыл бұрын

Hi Martin, I am not sure if this can be an issue or not, but I think touching the wires with the fingers before crimping the terminals can cause some oxidation on the contacts. Wouldn’t be better to clean them with isopropyl Alcohol before? Nice video as usual. Thanks, Marcelo.

@Cronus577 9 жыл бұрын

Wow, all the information here is going to help me so much when I rewire my car. Now I can make sure I do everything correct on a professional level. Thanks!

@evrik78 2 жыл бұрын

This guy embodies perfection.

@80s90sGuy 7 жыл бұрын

Nice video. I was always a bit unsure of weather to 'tin' wires before crimping. now i know not too...

@ffddkft1553 2 жыл бұрын

Gree

@mattd28 10 жыл бұрын

Excellent video, I do a lot of crimping in automotive applications mostly JST/Micro Timer etc, if anyone needs any help with those I can advise. Easy rule.. crimp connectors and solder only when joining wires

@sweetpadre 4 жыл бұрын

By any chance, do you know if I can hook up a 1500 watt inverter with a 4 gauge wire set up to 2 gauge battery cables? Will this be safe? I know I can't do it the other way around but I'm not sure if the appliance has a smaller wire will it still be safe? Thank you for your answer in advance.

@rdmccracken 4 жыл бұрын

@@sweetpadre That will be fine. Your inverter has a fuse which will protect it from over-current. Use as large a supply wire as you like - it won't make a difference as long as you are 4ga or larger.

@sweetpadre 4 жыл бұрын

@@rdmccracken thanks.

@horiafaliboga 7 жыл бұрын

One very competent vid nicely done. Not many folks really knows whats 'behind the scene' and how to do it properly like you demonstrate us. Thank you!

@nickpaz2421 2 жыл бұрын

One of the best tutorials I’ve seen.

@TampaTec 7 жыл бұрын

great video, liked and shared

@selvol 9 жыл бұрын

Actually you can Release Before You are done or have completely ratcheted the crimp tool. Release once you are done (15:18) There should be a small thumb lever on the tool witch will release the jaws at any point. I have not seen a ratchet style crimping tool with out one. Thankx 4 the Vid.

@mjlorton 9 жыл бұрын

Sol Shady Thanks for the post...you are correct!

@ficolas2 6 жыл бұрын

Sol Shady but that is only in case you mess up and cant finish, like if you "accidentally" start to crimp a hardened steel bar

@twig3288 5 жыл бұрын

The release lever is very handy if you accidentally crimp your finger.

@bponte 10 жыл бұрын

WOW, probably the best one of these videos I have seen on this subject. All the little details I never thought about or knew about and an explanation of the use of the better crimping and stripping tools was useful.

@nachiketmhatre7411 4 жыл бұрын

The only guy on KZfaq who knows that crimping provides better mechanical durability (and vibration resistance) and electrical conductivity than soldering. Also why you won't find anything soldered in a car's engine compartment. Or any machine that's subjected to severe vibration.

@4xoverland 7 жыл бұрын

Excellent. Thanks.

@ondrejhurinek 3 жыл бұрын

Just about to fix wire on my bike, didnt expect Andrew here :)

@moosack3701 3 жыл бұрын

👍video

@ratssled 10 жыл бұрын

Don't twist the bare wires! You want the strands to be nice and straight to ensure a complete and effective mechanical crimp. Very nicely done. One recommendation, show the proper method first, then show what not to do.

@gears4brains118 8 жыл бұрын

I really appreciate this video, All of this is new to me. I'm learning to do my own wiring on my truck/trailer cause it craps out every year thanks to the harsh environment of the truck bed/under the vehicle in New England. Thank you for making this very informative video.

@abe677 5 жыл бұрын

My father taught me many things about electricity but not about making good crimped connectors. Excellent video. I've had a container of vinyl insulated terminals for years and never knew how to attach them properly. After watching this video I ordered some die sets for a crimper I have (for PowerPoles) and had some fun tonight.

@ruanlessing781 8 жыл бұрын

Let's play a drinking game. Every time he says macanical take a shot. Let's see how long you last....

@dizzydean2458 7 жыл бұрын

You would get drunk quicker counting "potentially" and "invariably"

@rickharms1 6 жыл бұрын

ruan lessing I

@Landrew0 9 жыл бұрын

It's one thing to be thorough, but it can become painful to watch when it's stretched-out too long.

@78a67h 5 жыл бұрын

Just have a cup of coffee and puff a long cigar while watching

@WelcomeToMyDream 5 жыл бұрын

My fancy computer lets me skip to any part AND speed up the video in these cases. I know it sounds crazy, but I can also select shorter videos. It's because I'm rich, rockin the $200 laptop.

@carolinerichards5081 3 жыл бұрын

Very helpful. Thanks so much! Appreciate your thoroughness and style of presentation

@chaseallen9390 7 жыл бұрын

I learned a ton from this video. It is indeed very thorough. He loves to use the word "mechanically" too lol.

@nsoper19 9 жыл бұрын

how many multimeters does he need? great vid though

@waswestkan 7 жыл бұрын

As a particle matter practice at least two. The dude does product review videos that's probably why he has so many to display.

@odahithedubious2017 8 жыл бұрын

You should avoid touching the bare conductors with your fingers. The oils on your fingers will interfere with your connection and possibly even cause corrosion. The only time I use the crimper/stripper tool, like the "RACO" blue-handled one you have, is when I want to verify the size and thread pitch of a screw. I never use those tools for stripping or crimping, they do not make reliable connections. Colored shrink tubing is sometimes used to disguise inferior work. We don't use it where I work, as all our work is inspected. I have used it with good results at home, although it is not preferred. It should be sized correctly and applied with a heat gun, not a flame, as the tubing can char, crack, and burn, leaving uninsulated areas in your connections. It is unnecessary to have a very long piece of tubing. Depending on the wire gauge, 5-15 mm may be adequate tubing behind the lug and up onto the wire insulation. This will also permit the wire to be routed to its destination more easily. (I've been NASA certified since 1996 and have worked in aerospace since the late 80's).

@Bman130958 4 жыл бұрын

I call bull-shizzle on your NASA cert claim. I'm sure at any NASA level, there is some sort of National Secrets Legislation that prevents disclosing any information about employment.....that leaves wanna-be, dip-shits like you pounding out "meadow muffins" on the keyboard.

@Korbin57 10 жыл бұрын

Very informative and useful. I've been crimping wire for decades and still learned new things. Excellent.

2 жыл бұрын

EXCELLENT VIDEO!! Thank you sir!!...👍😁

@Mataz007 10 жыл бұрын

15:58 the only part of this video I understand.

@SilverSurferFTW 10 жыл бұрын

You never use ground colors for live cables!! This is a basic safety rule...

@eliasghosn6754 10 жыл бұрын

Tell that to old Honda motorcycles, black is a live color all through the harness

@kl1nk0r 10 жыл бұрын

Elias Ghosn I believe he meant the green/yellow cable which is labeled "POS+".. And I agree strongly

@TheChipmunk2008 10 жыл бұрын

Simon K. It's actually acceptable under UK regs at least to use g/y for a non-ground/earth purpose if reidentified at each end. I do NOT like the idea though.

@brk932 5 жыл бұрын

1. You would also never assume a red/brown/black/grey colored cable is live either. You always measure before work and double check connections at the ends. 2. You always count the person that worked on that gear previously is a baboon with a hairdo. p.S. I have never been disappointed on the latter as can be attested by the local fire department and barber's shop

@shockingguy 4 жыл бұрын

He covered all that, and he made up a cable for something he needed for batteries, not for house village. You know you can do whatever you want at home as long as you know what the hell you’re doing.

@brianread 10 жыл бұрын

A very good "how to" video. Highly valuable with the insights from an experience user / tech. I am very appreciative that MJLORTON provided this video.

@ananthardikar5124 2 жыл бұрын

Amazing and thanks dear, can not imagine to have better explanation than this

@lucyd1815 8 жыл бұрын

I went through half of this video and realised this isn't a crimped hair tutorial.

@a705fay 8 жыл бұрын

+Lucy Donaldson good if you want a fuller hairdo

@dancelessonsorlando7231 7 жыл бұрын

Ha! Cute.

@TheHitmanuk1 6 жыл бұрын

Lucy D I went though the whole video and realised I have a shaved head.

@DanGOchoa 6 жыл бұрын

LOL =D

@FrankEdavidson 6 жыл бұрын

When I was an apprentice electrical technician my employer told me to buy proper crimper. From then on I had lovely textured hair.

@alexsbikesandmotors 8 жыл бұрын

why do you have so many multi meters?

@obfuscated3090 6 жыл бұрын

HERESY! I scatter meters everywhere so I'm never more than a few feet from one.

@josuevillasante2546 6 жыл бұрын

Diferent vo;tage jajajajajajajaaj

@leocam3880 11 жыл бұрын

Hey, good video! Thanks for dedicating time toward helping out lost folks like myself.

@davidschwartz9636 4 жыл бұрын

Handy video, thanks for sharing your knowledge and experience. Putting on crimps seems a simple thing to do, but like you say, it needs to be done correctly. Unfortunately, a lot of people do it the wrong way, I'm guilty of doing the solder tinning before crimping. - won't be doing that again now you've explained why. Regards David.

@jacobfalk4827 9 жыл бұрын

Invariably haha!

@djtyros 3 жыл бұрын

...beat me to it... 6 years ago

@TigredelMar77 10 жыл бұрын

I myself work in the manufacturing field specifically on the cable area and for anybody that wants to learn this is a great video, of course some of the european components and tools could be a little different that the american components and tools but the principals are the same.