Twin disc vs single disc clutch comparison: McLeod RXT Twin Disc Breakdown, disassembly, config

Рет қаралды 9,398

Күн бұрын

Full RXT, pivot ball stud, input shaft video 03/04 Cobra Mcleod RXT, 26 spline input shaft, throwout bearing, pivot ball stud, pilot bearing
• 03/04 Cobra Mcleod RXT...
Ford racing throwout bearing amzn.to/3IYZDQN
Transmission jack sold here amzn.to/3vAxImd
High temp grease amzn.to/35MeRJZ
Clutch fork (highly recommended) amzn.to/3tw3Nsx
Pilot bearing amzn.to/3Kgnlbo
RXT INSTALL • McLeod RXT Install & P...
26 spline input shaft install • 26 spline input shaft ...
Clutch removal (Part 1/2) 03/04 Cobra T56 Clutch, Throwout bearing, pilot bearing replacement release bearing
• (Part 1/2) 03/04 Cobra...
• Mustang Maintenance an...
Disclaimer: I am an amazon affiliate and may receive a commission for sharing the link, but the price will be the same for you.
The concepts performed in all videos from Scrun Johnson are for demonstration purposes only and are not guaranteed in any way as I am not a certified mechanic. The viewer holds the responsibility to research these procedures and perform them at his/her own risk.
Due to factors beyond the control of Scrun Johnson, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Scrun Johnson assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Scrun Johnson recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of Scrun Johnson, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not Scrun Johnson. Always take proper safety precautions, including, but not limited to, wearing safety glasses, removing jewelry, properly securing the vehicle on jack stands, etc.

Пікірлер: 29

@jalexs5283 Жыл бұрын

Great in-depth explanation as usual, Danny. I think it's BS how McLeod strongly recommends balancing their product, yet just doesn't do it from factory. With shipping and what they'll charge you, it'll easily add a few hundred dollars to the cost of an already expensive clutch - and then the time and hassle you have to deal with shipping. McLeod is the only clutch I know that doesn't sell you a clutch ready to go. I wish I would have know this before I bought mine, I'll see how it treats me.

@Airman.. 9 ай бұрын

Outstanding work thanks

@Lethal_Venom Жыл бұрын

Great comparison. I got mine as an open box item off from American Muscle and saved a decent amount then sent it back to McLeod to be balanced. I’m sure a lot of people miss this step and never get it done and then complain about how it performs later on

@dannyjohnsonsgarage Жыл бұрын

Do you know if they balance only the flywheel or attach the entire kit to be balanced as a whole?

@Lethal_Venom Жыл бұрын

@@dannyjohnsonsgarage that I’m not sure, I just know the clutch and flywheel came attached after balancing it like in the video

@drakenash7654 5 ай бұрын

Awesome video.

@dannyjohnsonsgarage 5 ай бұрын

Thanks! You’ll probably like the install as well kzfaq.info/get/bejne/prepdZOcy7Teqqc.htmlsi=DeykdaApTWMb0GoX

@brianfarner85 Жыл бұрын

Interesting, I never saw anywhere in the McLeod instructions that my flywheel wasn’t balanced from the factory. I guess this is why my RST and almost everyone else I’ve heard install a McLeod twin disc gets chatter at lower engine speeds. Mine sounds nasty right about 1900 rpm. I don’t understand why they would sell a flywheel that’s not balanced at the factory.

@dannyjohnsonsgarage Жыл бұрын

Yeah, it’s on the cover sheet of the instructions. Might just be a way to remove any blame cause I called around and no one will balance mine. It should be balanced against the crank is what they tell me, so I’ve thought about measures to spin the assembly before mounting the transmission behind it, but don’t want the clutch discs moving out of place without the input shaft holding it. Clutch chatter in each gear when shifting is normal on any new clutch. My mach 1 shook the steering wheel when it was new. I wonder if ford wears ir down from the factory since new cars aren’t like that

@stevegiunta8532 Жыл бұрын

Hey Danny good video yeah I got to pull my transmission this weekend on my 01 cobra before broke where it hooks onto the ball have you ever heard of such a thing and also LOL I wish you and your brother Justin lived closer to me I would love to have the help by you guys you are experts

@dannyjohnsonsgarage Жыл бұрын

Which ball?

@stevegiunta8532 Жыл бұрын

I'm sorry Danny the clutch fork the side that hooks onto the ball and the other side hooks onto the clutch cable the side that hooks onto the ball broke

@stevegiunta8532 Жыл бұрын

Hey Danny my proportioning valve for my brakes went out on my 2001 cobra do you know of any company that sells new ones

@TheNightmare692009 Жыл бұрын

I have a McLeod 8 bolt steel flywheel that I got balanced when my motor was built for my 03 GT. The whole rotating assembly was balanced. I have since bought the RST organic 26 spline clutch to go with it after upgrading to a TR 3650 Lashbrook trans. I hope the clutch and flywheel will be ok together as they were not bought as a set like yours. What problems, if any, could I expect?

@dannyjohnsonsgarage Жыл бұрын

To run the clutch kit with another flywheel it should come with the adapter plate/ring, so make sure it has that. I could not find anyone in town who would balance my flywheel, so after seeing it had been “zero balanced” from the manufacture before it was added to the kit makes me think it should be okay. Probably the same with yours. Just see if you get any vibrations when it’s all said and done.

@TheNightmare692009 Жыл бұрын

@@dannyjohnsonsgarage Thanks. The only time I've seen a flywheel balanced is with the motor balancing from the lower damper to the flywheel.

@user-ng1ld3jk5q Ай бұрын

Are twin disc clutches and multi plate clutches the same?

@dannyjohnsonsgarage Ай бұрын

I do believe that is another name for it

@DeveryAndrews Жыл бұрын

I’d take photos with my cell phone during disassembly for additional reference.

@dannyjohnsonsgarage Жыл бұрын

I’ve not only taken pictures, but also videos of the measurements

@modlist6129 Жыл бұрын

Will you be making a install video for the input shaft?

@dannyjohnsonsgarage Жыл бұрын

I plan to if it ever ships

@dannyjohnsonsgarage Жыл бұрын

Until then, I have the retainer sleeve video that pretty much shows it. You just need to check the end play with the new input shaft when the cover is installed. It has to be .002-.000 kzfaq.info/get/bejne/e9mRgqWA3pybmGg.html