TWO EASY METHODS FOR MEASURING LS PUSHROD LENGTH!!

TWO EASY METHODS FOR MEASURING LS PUSHROD LENGTH!! - TURBO 5.3 LS pt 9

Рет қаралды 14,923

Күн бұрын

In this video - Erik shows you TWO different methods to check your pushrod length on an LS engine!! Time stamps and part numbers/links below!!
GODSPEED GARAGE T-SHIRTS and MORE!!!
**Get FREE SHIPPING on orders over $40 using code FREESHIP40 **
GSG MERCH: godspeedgaragemerch.bigcartel...
COMP CAMS LS PUSHROD CHECKER - www.speedwaymotors.com/COMP-C...
intro and important info 0:00
METHOD ONE 1:28
METHOD TWO 7:44
Copyright GODSPEED Garage, LLC. 2022 All Rights Reserved
*Disclaimer - This video is intended for entertainment only. GODSPEED Garage, LLC, or anyone involved in making this video is not responsible for any damage to person or property that may occur attempting this on your own. You assume all responsibility for your own safety as well as use of your property.

Пікірлер: 19

@RipThatVette 4 ай бұрын

Big thanks for taking the time to clearly explain this process. The other videos I’ve watched have been confusing.

@e.s.l5861 Жыл бұрын

This is the best tutorial I have found for this procedure

@themildgoose Жыл бұрын

Extremely informational on this, I did my first cam on a gen 4 6.0L and the pushrods were doing my head in with the ticking and not knowing the base circle had changed. Big thank you from a dumb ass trying to get his engine right, and extra points on background tracks!

@alexanderknight7793 Жыл бұрын

Great video, I like that you described it clearly in both methods.

@GODSPEEDGarage Жыл бұрын

Thank you!

@ralphfreeman255 Жыл бұрын

About to build my LS swap and appreciate the video!

@user-jo9fy4ls2e 11 ай бұрын

Great stuff Brother!!!! Thanks!!!

@brianhaw9398 2 жыл бұрын

Thanks,some good info.

@marcogonzalez7409 Жыл бұрын

Really helpful video 👌

@GODSPEEDGarage Жыл бұрын

Glad it was helpful!

@julz5915 2 ай бұрын

Hopefully I can figure this out now

@fladrummer1 Жыл бұрын

Thanks for the info building a 6O in a C5 Texas Speed heads has been a nightmare 7.4 push rods but dont think the mechanic did the math or put the pushrods on the small lobe of the cam going to a performance shop today......

@Abraham_R_ Жыл бұрын

1st time measuring pushrod length here, but I have a question see if anyone could give me advice, I basically did everything like he did on the video even the math but with my measurements, so my intake is 7.2875 rounded it to 7.300 and my exhaust is 7.325, should I buy all the pushrods 7.325 or should I buy half and half?

@Robert-uc5pb 7 ай бұрын

I'm doing a head gasket job on an 07 Yukon Denali 6.2l. I got the heads on and now I'm doing the Rocker arms. I noticed when I'm torquing the arms some of the rockers slide from the center of the valve stem and moves closer to the edge of the spring. My valve springs are slightly compressed also when I finish torquing to 22 ft lbs. Can you tell me what can be the problem? I'm stumped

@Weinhoffercustoms Жыл бұрын

I always torque the Fastner to spec then check for zero lash

@chazdunaway8240 2 жыл бұрын

did you add pre load to you length or did i miss it?

@Recklessfireblade 2 жыл бұрын

Yes you add it to whatever preload you need. Most lifters such as Johnson lifters will have a specific preload on the box. GM lifters have a much broader range and are more forgiving

@GODSPEEDGarage 2 жыл бұрын

yes. for the first method you have to add it. the second method (the turn method) accounts for the pre-load. I second what @Brandon Ouzts said - GM lifters have a really broad range. as long as you're in that range you're good. hope that helps!