TWOTREES TTC450 CNC - Great First CNC!

Рет қаралды 36,017

Жыл бұрын

#cncmachine #cnc #twotrees #pcbway
PCBWay: www.pcbway.com/
Save $50 use code: TGTC- shareasale.com/r.cfm?b=240071...
This is my first attempt at using a CNC machine! Lets see how I do!
‪@Twotrees3Dofficial‬
Machine Specs
Engraving size - 460*460*80mm
Spindle - 74w - 80000rpm
Dual Y-Axis Steppers
32bit Board - DLC32 v2.1
3.5in Touchscreen
Max Speed 800mm/min
Wifi
Running Accuracy +-0.1mm
Compatible Software - Candle, Carveco, Artcam, Easel, Carveco
Double Homing limit switches on X,Y, and Z
Software -
Easel - easel.inventables.com/ ‪@inventables‬
UGS - universalgcodesender.com/
Carveco - carveco.com/ ‪@Carveco‬
Recommend watching!
/ @jamesdeandesigns
• Setting up your first ...
• Beginners guide to des...
• Beginners guide to des...
• Setting up the Z probe...
Disclaimer - This is an instructional video only - I assume no responsibility if you do not become a pro after watching this video. This video is for learning purposes only, you are following the steps in this video at your own risk!
/ tripodsgarage
/ tripodsgarage
/ tripodsgarage
Thanks for watching - Please Like and Subscribe!
Tags
Kywoo, Tycoon, Tycoon Max, Tycoon Slim, CR6-SE, CR6SE, 32-Bit Control Board, TMC2209 Stepper Motor Driver, 3D Printer, 3D Printing, CR-10, CR-10s, Ender 3, Ender 3Pro, Ender 5 Pro, Ender 5, creality silent board, silent board, BIRGTREETECH, SKR CR6V1.0 #tycoon #tycoonslim #tycoonmax, ATOMSTACK A5, #ATOMSTACK #ortur #xtool #laserbox #thangs #40watt 40 Watt laser #thangs.com, cnc, TwoTrees TTC450

Пікірлер: 47

@stevejones01 10 ай бұрын

The wires rubbing against the frame is because the drag chain is too far forward on the Y axis (go to 3:02 and zoom in). The rubbing cable that comes out of the end needs to bend back to connect. It can't bend back with enough slack to keep it out of the way of the fame when tied to the side of the upright. Unsnap a couple of bars (not the entire link) from the top of the Y drag chain to release a little more cable. This will let you wire tie it to the back of the upright instead of the side. The video on the SD card shows the cable tied to the back not the side. The cable doesn't get in the way of the limit switch when tied this way (tested).

@bclp52 Жыл бұрын

Thanks for the video. Very informative.mine is still in the box I haven't had time to put it together.

@luisoquendo5656 11 күн бұрын

A couple month ago I got a TTC450. Then I designed couple jobs, put them in a flash card, loaded them in my laptop; then I set up the machine and a piece of wood. When I push the start button the spindle start rotating, but nothing; it remained in the same spot. I'm missing something. Any idea? I use V-carve pro, GRBL and G-sender. Thank you for any help

@kristianserbak9392 8 ай бұрын

I should do a trial run on the TTC450 CNC machine, the text that should be engraved. However, I have a problem when I let the machine do the process. It does not actually touch the bottom of the tree on which it is supposed to work, although I went to the Z test several times to adjust the height, however, the machine does not work correctly for me, it works non-stop in the air and non-stop returns up instead of down. How can I regulate so that this does not happen to me, so that it starts working normally. I don't know if it's not a problem in the Candle settings. I use machine dimensions 460x460.

@jlssculpturedesign8140 Жыл бұрын

Hello and great video , i have been researching hobby cnc(do not own one ) . Another option is painters tape on spoil board ,and piece on underneath of work piece with super glue betwen them .

@petercasper224 Жыл бұрын

Fantastic vid! Always enjoy watching your reviews.

@emmayu4343 Жыл бұрын

me too!😛

@TripodsGarage Жыл бұрын

Thanks! Much appreciated!

@trisectdevelopment 4 ай бұрын

I clicked on your link, but I cannot see if i get the probe if I get the one with the machine and the 500W motor. I really want to have to probe if I is to buy it.

@SHLAPGANG 2 ай бұрын

Can it cut through 2-3 mm of ABS plastic?

@JMAJOR-ki7ur 3 ай бұрын

For the gap where the wire get caught, maybe fixing brush hairs along it to keep the dust out ?

@HAMRADIODUDE Жыл бұрын

Hi, I'm also a total rookie. In Carveco, what did you select for your Machine File Format? There are plenty of different printers, but nothing I can find related to the TTC450. Thanks!

@enverocsa8066 8 ай бұрын

Lograste encontrar alguna solución

@drenz1979 2 ай бұрын

Can this cnc print to cut?

@SirTools Жыл бұрын

Just found you tonight, but good video. The left side cover ! I removed about 10mm along that opening and the cable is no longer rubbing. Also the new upgrade kit is here just waiting for TwoTrees to give me the "go ahead" and show off the new 500watt motor etc...

@TripodsGarage Жыл бұрын

Thanks for finding me 👍. That 500w motor along with dust collector will make this one amazing CNC!

@SirTools Жыл бұрын

I think the spindle was rather small, but this new one looks like a beast. 😃

@disposablefiendnuxmu Жыл бұрын

I purchased this because of your video!

@TripodsGarage Жыл бұрын

Much appreciated! Hope you enjoy it 👍

@woodwaker1 Жыл бұрын

Looks like a good machine fro the price. I only have one workspace and my 4 3D printers fill it, plus they make a big enough mess already.

@TripodsGarage Жыл бұрын

Definitely needs the dust collector. It does take up a decent amount of space, and looking in my garage for placement. Thanks for watching bud! There was a Bear sighting 😉

@mikejackson9585 Жыл бұрын

Looks like you may want to get a flat faced endmill and a ball nose end mill to clean up the operations with a finishing passes (meaning set up your main cut just short of the final pass finishing depth and take a shallow clean final pass). The ball nose will smooth out the rounded areas and the flat end mill and a finishing pass (maybe a .10 or .25mm) will clean up the rough flat zones. Fusion 360 free hobbiest version is still the best CNC software. But there's a learning curve. At least until they make it a paid software.

@MikeSmith-vp3ql 7 ай бұрын

I’m new to CNC and just ordered this model. I was going to ask if different bit would make the end product better. You have answered my question thank you.

@privateeye242 14 күн бұрын

What makes Fusion 360 free version the best CNC software? With which other products did you compare?

@mikejackson9585 14 күн бұрын

@privateeye242 Fusion is the most feature packed software out there, and it's pretty much the only option that can do both CAD & CAM for free. It's powerful, so it takes time to learn, but there are a ton of resources out there. There are other tools like FreeCad, but honestly, it doesn't hold a candle to Fusion. But if it was all we had, FreeCad is pretty powerful too, just difficult to learn and use. Easel is a very simple program that is easy to use and works great for simple projects, but doesn't hold up to Fusion for more complex projects. So, for simple projects, Easel is probably the best and easiest to use. But if you are up to learn how to properly machine stuff, Fusion is the way to go.

@blazenboo2 7 ай бұрын

can't (home) the machine. follow the directions exactly after spending 5 hours putting it together. tells me to "please unlock" homing failed....junk?

@darkerstill55 Жыл бұрын

The only thing you didn't cover is what materials it can cut. Ok it can do wood. What about plastics and metals?

@TripodsGarage Жыл бұрын

I wouldn't suggest using this CNC for metals. When milling metals it is suggested to use cutting fluids (cutting oil, cutting compound, or lubricant). It can engrave softer aluminum, plastics and wood using the correct end mills.

@chupsymoto1414 7 ай бұрын

can you try cutting aluminium

@JamesBiggar 6 ай бұрын

James Dean has 0 videos on how to set up the TTC 450. General CNC info, yes. Two Trees specific - no. Ain't got time for that.

@TripodsGarage 6 ай бұрын

You are 100% correct, he has no content for the Two Trees 450. Only used him as a reference for the software side.

@OldCurmudgeon3DP Жыл бұрын

Cool. Almost affordable.

@TripodsGarage Жыл бұрын

Yes, more affordable than an X-Carve 😆

@ronsone8373 Жыл бұрын

That sign took 10hrs? 😅

@TripodsGarage Жыл бұрын

Yeah 10hrs. The spindle doesn't have the horse power or the RPM's to push if faster.

@ronsone8373 Жыл бұрын

@@TripodsGarage then a no go for me 😅 thanks for the heads up

@TripodsGarage Жыл бұрын

@@ronsone8373 Yeah, isn’t for everyone. They do offer an upgraded spindle.

@soerenhuba 4 ай бұрын

Even as a hobbyist, I don't think there is a way to sell this machine without the 500 W spindle. With the factory spindle, this machine is more like a Fisher Price product. Its built is sturdy and robust, it can easily handle the more powerful spindle. There's some good engineering but the communication and information "strategy" from the manufacturer are terrible. Between the setup instructions, the cable drag on the left side, the screws coming loose and having to undo everything, the mistakes for installing the firmware (having to remove Chinese characters), the user is left guessing WAY too often. @@TripodsGarage

@emmayu4343 Жыл бұрын

Nice content!!!

@TripodsGarage Жыл бұрын

Thanks! Much appreciated!

@MrMatador1955 2 ай бұрын

I purchased recently a two trees ttc 450, im getting a error code ¨ hard limit ok¨´ on the screen, i tried to disconnet power several times n still the same error on the screen, is there something i can do?

@Twotrees3Dofficial Жыл бұрын

So dope! Greatly appreciate my friend, Tripods. We are honored that you enjoyed our product! Thanks for sharing your experience with your followers! and welcome all friends to follow Tripods and TwoTrees, we hope we can grow together and become better

@TripodsGarage Жыл бұрын

Thanks for the kind words!

@Twotrees3Dofficial Жыл бұрын

@@TripodsGarage can't wait to see your more wondrous works

@soerenhuba 4 ай бұрын

Can't wait to see more videos on how to deal with screws coming loose and how to handle the dragging wires. I bought the machine 3 months ago and am facing having to disassemble it entirely again.@@Twotrees3Dofficial