Ultimate Grainfather Setup! Conical Fermenters & Glycol Chiller

Рет қаралды 13,100

Күн бұрын

Grainfather Conical Fermenters and new GC2 Glycol Chiller are next-level pieces of homebrewing equipment that will help to significantly improve the quality of your beer through better fermentation temperature control, yeast handling, and transferring. In this video we show you how these pieces of equipment work in connection to each other, including assembly, setup, usage with tips from our resident Grainfather guru William Richartz. See timestamps below for specific equipment or topics. #homebrew #grainfather #brewingequipment
Grainfather Conical Fermenter: bit.ly/44DMjvp
Grainfather GC2 Glycol Chiller: bit.ly/3DasTCD
Shop Northern Brewer's full collection of Grainfather equipment:
bit.ly/44hsY3i
** Chapters/Topics **
00:00 - Grainfather Demo Introduction
01:44 - Glycol Chiller: Priming & Setup
04:35 - Conical Fermenters Setup
06:34 - Install: Standard Control Panel
07:27 - Install: Wireless Pro Controller Panel
09:39 - Tip: Grainfather Conical Coat
10:31 - Brew Day: Filling Conicals, Attaching Tubing
12:21 - Tip: Trim Tubes to Proper Length
13:42 - Setting Controllers for Fermentation
14:59 - Cold Crashing Beer
15:39 - Dumping Yeast
16:54 - Filling Keg from Transfer Port Valve

Пікірлер: 26

@NorthernBrewerTV Жыл бұрын

Check out our full collection of Grainfather equipment and accessories: bit.ly/3O6M4nc

@batking911 8 ай бұрын

I remember the ports on the fermenter as “Hot” = “High”, “Low temp (cold)” = “Low”. Has worked for me! Currently using cooler with ice with cooling kit but the 2 port glycol chiller is definitely next on my wish list!!

@NorthernBrewerTV 8 ай бұрын

Great tip!

@nivek2157 Ай бұрын

Great review. Thanks guys.

@jonsalatdenung5519 2 ай бұрын

Great video! Exactly what I was looking for. No more, no less.

@matthewhennessy2505 Ай бұрын

Excellent content.

@christiann.7195 Жыл бұрын

I am using the Conical for a very long time and I love it. I feel like you missed the main selling point of this fermenter that sets it apart from any other on the market. It is double-walled and this helps a lot to maintain temp.

@tesujisoftware Ай бұрын

Great video.

@raymondboyle2722 7 ай бұрын

How about another vid showing the pressure transfer with GF kit. I bought the kit but need to learn how to use it best practice.

@silveraven1 4 ай бұрын

Very complete and clear directional video! 1: Do you have to prime the chiller every time after you disconnect it? 2: Can you share your fermentation schedule for that beer you were doing? Thanks again guys!

@africantwin173 Жыл бұрын

I used the GF conical 4 times. The 4th time i was doing a Neipa with loads off hops in it. Quess what, hops all got stuck in the cone. O-rings damaged. And the lid leaks when adding a few psi co2. After that time i was done with GF Fermenters. I sold it the day after. But i do like the G40. Jacketed 14 gal Unitanks with big TC ports are the way to go now. I used the GF conical with a Mini freezer, 10w aqua pump,inkbird 308. The GF glycol chillers cost 800-1200 euro. To pricey.

@andrevangijsel957 10 ай бұрын

If you put the isolation over the brass connectors then the condensation just pours at the the end near the chiller. At least in my case. Is there some otherway to catch the condensation moist?

@raymondboyle2722 7 ай бұрын

Can NB comment on the GC2 having a hysteresis of >5F. I experienced this on my first brew with this system. Wort in the fermenter at 66F. And this was my fermentation temp setting. But the initial fermentation was very vigorous from a good starter and the temp rose to 71. But the GC2 never kicked in until then. Then it did quickly drop the temp, but it rose back up as fermentation continued. Ok I'm a novice with chilling with glycol, but this is not a better fermentation temp control I signed up for!

@MaryBrownForFreedom Жыл бұрын

Instead of electrical tape I would use adhesive lined heat shrink tubing, basically heat shrink with hot glue inside it. Water tight connections!

@PetraKann Жыл бұрын

Best solution

@dougschriever1480 Жыл бұрын

I love the system. I have the same set up but with 3 fermentors, will be getting the 4th on there next sell. What is the piece of equipment you are using at 10:37? I am needing one of those for my mash. Please let me know.

@NorthernBrewerTV 11 ай бұрын

Sorry for the delayed response! That is one of our Imperial Sparge Arm setups. Check it out: bit.ly/442ob4X

@prodanman 9 ай бұрын

Couple Questions: Does the GC4 come with 4 pumps & insulated cooling lines? When ordering the GF30 fermentors do I order set of insulated lines or are there any included with the clycol chiller When ordering the GF30s

@NorthernBrewerTV 9 ай бұрын

The GC4 specifically comes with two insulated tubes and sets of brass connection couplers, which is required to hook one fermenter up to the unit: www.northernbrewer.com/products/grainfather-glycol-chiller-with-cooler-connection-kit Additional tubing kits need to be purchased for any additional fermenters. www.northernbrewer.com/products/grainfather-conical-fermenter-cooler-connection-kit

@edhoule4532 Жыл бұрын

I just bought the grain father conical fermentor pro edition same setup as yours with the foam jacket I’m using a diy glycol chiller with the Grainfather pump system with the insulated lines my glycol tank is 20 liters temp is a steady -8 degrees Celsius with my testing of this fermentor I have 23 liters of water in the fermentor the temp set to 4 degrees Celsius the start temp of the water was 20 degrees Celsius the room temp is 22 degrees Celsius the first day the temp hovered around 6 degrees Celsius at the censor at the bottom but the temperature at the top half is at -1 degrees Celsius with a thin layer of ice on the top second day turned up temp to 6 degrees on the fermentor now the the top of the fermentor is around o degrees Celsius no ice on top it seems like there is a flaw with this design can’t get the bottom half below 6 degrees Celsius with out freezing the top half I have noticed that all the videos are not showing this fermentor cold crashing this is the reason I bought this fermentor so I could free up my fridge and use it for my kegs do you have any helpful hints thanks

@askaryambus 10 ай бұрын

So, just to understand, the Grainfather will help me at maintaining temps during fermentation? I didn’t see a heating element. Thanks

@alexfoster1032 9 ай бұрын

As far as I am aware, the heating element in the cone at the bottom of the fermenter. Please correct me if I am wrong :)

@JoeyNix Жыл бұрын

How do you handle suck back when cold crashing?

@NorthernBrewerTV Жыл бұрын

Since shooting this video William actually started doing his cold crash in slower stages, cooling the beer only about 7-10 degrees a day until it reaches cold crashing temperature. He says that seems to help (versus a quick mid-70s to upper 30s drop).

@prodanman 4 ай бұрын

Will this Cold Crash at 33°f???