Ultimate Guide - RP2040 Nintendo Switch OLED Install Visit us online at: Wayayeo.org Like and subscribe if you like this video. EDUCATIONAL PURPOSES ONLY
Пікірлер: 48
@NPC-Electronics-Tech3 ай бұрын
really good video, used it to mod my oled with no issues! Thanks amigo
@Wayayeo3 ай бұрын
This is what I like to hear. I’m very glad it helped. 👍
@junjloc37743 ай бұрын
I hope you charge well you have some real skill and make it look super easy
@jackipiegg3 ай бұрын
12:48 Do cover the inner side of the nand shield with kapton tape. The solder blob will touch the shield (grounding it) at some point in time if the console is dropped or shaken. Happened to me once.
@Wayayeo3 ай бұрын
Good point. Thank you.
@quajay1873 ай бұрын
I find that the dark blue Dat 0 connector is more stable than the yellow one
@jmp913 ай бұрын
yesss
@error34629 күн бұрын
Can you explain the software part to finish the work? Thank you!
@underscore8142 ай бұрын
At 5:04 i recommend once slid in to check with the multimeter to ensure you are getting the correct readings before grounding it to the shield.
@Wayayeo2 ай бұрын
I’ve done it so many times that I developed a good hand but your advice is definitely good. Thank you for the input.
@user-mc1op7wv1e2 ай бұрын
I hate to be that person, but what are you installing on the board? I’m pretty sure it’s some kind of bypass or a common issue on these Oled’s, but I haven’t worked on any thus far, but would love to know what issues this resolves with them Thank you
@OkiDingo2 ай бұрын
Was that my Splatoon OLED? I’m curious why you don’t put the heat shield back on after install? Is it just not necessary?
@tonycheck28 күн бұрын
Hi, thank you for this tutorial! Where i can find that dat0
@qaishusam3 ай бұрын
Thanks for your video! Do you mind sharing the model of your microscope? Footage looks sharp and detailed. Good job 🎉
@Wayayeo3 ай бұрын
You’re welcome. Microscope is a Leica. Camera is an Eakins. I have tried a few others and pretty much any $300 and up look the same. Got it on aliexpress, no model #.
@hannoverfisst2414Ай бұрын
@10:55 you dropped some solder on the bottom of that 3.3v connection at the top of the ribbon cable real quick but you didn't say anything and when I pause it, it looks like there are connections at the top and bottom but you just did a real quick job on the bottom connection but not the top? @ 12:05 you show a really good pic of it but the top is not soldered? Does that 3.3v not need to be connected at both ends? It also looks like you're supposed to jump the two together on the top and bottom? What's going on there? Seems kinda important.
@Wayayeo5 күн бұрын
Bottom of cable is the 3.3 v top is ground but chip is already grounded so not needed. Just saving time.
@enerqiezz2163Ай бұрын
Which Temperatur is recommended?
@WayayeoАй бұрын
680F
@x1ic1x3 ай бұрын
10:26 for some reason solder never wants to grab the flex cable with this resistor, does it even need to be soldered together to work?
@Wayayeo3 ай бұрын
No need to solder it. It will work just fine as this is just for support.
@rogergillette8426Ай бұрын
So I attempted this myself, though I did ok, had all the right readings. Got the firmware flashed and it won't boot. It gives me one solid blue light, then yellow x2 a pause yellow x2, pause yellow x2 and then nothing. What could I have possible messed up? 🤦♂️
@WayayeoАй бұрын
Possibly your DA0 point but I’d check for any shorted points. Good luck
@rogergillette8426Ай бұрын
@Wayayeo yeah, I'm not sure... I think I messed something else up, I removed it and the system still wouldn't power on, so I think it's a new mobo time and pay someone with better eyesight to install it 🤷🏻♂️😬😅
@evenemad5010Ай бұрын
Which microscope did you recommended me to get one? Thanks in advance.
@WayayeoАй бұрын
Anything from a $400 rage from aliexpress works fine
@evenemad5010Ай бұрын
@Wayayeo thanks for replying! Which wier soldering do you recommend my to use? I'm using this one ( Tin 97%, Silver 0.3%, Cuper 0.7%, Flex 2%), but I'm having a hard time to deal with it. My machine is Sugon A9. Big thanks in advance.
@triderg7-8163 ай бұрын
Thank u for this step by step tutorial. How can I recognise latest rp2040 mod?
@Wayayeo3 ай бұрын
You’re welcome. Get from a reputable seller. You can always upgrade firmware. Good luck !
@nixskups47882 ай бұрын
Hi, what is the temp. that you use for soldering?
@Wayayeo2 ай бұрын
It really depends on your equipment but I find 680-720 f works for me.
@nixskups47882 ай бұрын
@@WayayeoI have an smd soldering station hot air + stylo can reach 900 F. I ask this because I planned to mod my Switch v2 and dont want to overheat the pcb.
@LonzoTube3 ай бұрын
Which cables are you using? 36awg? At what temperature are you soldering it to make it strip so fast? Thank you
@Wayayeo3 ай бұрын
38 awg. 700F on soldering tip.
@LonzoTube3 ай бұрын
Thank you, I'm doing some practice and when it comes to wires, it's a mess for me
@S3SIC8313 ай бұрын
Thanks
@Wayayeo3 ай бұрын
You’re Welcome
@joesaiditstrue3 ай бұрын
Your videos are showing up in fyp feed to ppl who aren't subscribed. What's RP2040? should put more detail in the title
@Wayayeo3 ай бұрын
I appreciate the info.
@KngKurd3 ай бұрын
Raspberry pi 2040 is a chip that is universally used for lots of mods including picoboot on GameCube
@jeblimohamed69833 ай бұрын
Hello, thank you very much for everything you do I have a problem the device boots directly to the base system and does not enter the modified system The shape of the flashes of the LED lamp is as follows : kzfaq.infoO8dwRjmyKEs?si=zaDRE-_ccsvqzlR_ Can you help me solve this problem? Thank you very much
@Wayayeo3 ай бұрын
Check all points with multimeter. Also check for shorts.
@jeblimohamed69833 ай бұрын
@@Wayayeo ok thank you i will check
@GameOn-li6qe3 ай бұрын
I have this exact problem where it flashes blue followed by 2 yellows 3 times I checked all the connections are made perfectly no shortage either All the values appears to be ok on continuity any advise???
@jeblimohamed69833 ай бұрын
@@GameOn-li6qe In my case I think the problem is in point C As far as I know, the value should be between 0.6 and 0.7 For me, the color of the flash is blue and green maybe your problem is modchip firmware, i wish you find a solution