Ultimate Loose Tenon Jig [video 453]

Рет қаралды 234,137

3 жыл бұрын

In this video I make a loose #tenon #jig that duplicates the killer features of the Festool #Domino - narrow and wide slots in a single jig. And yes, I had to go there with that 'ultimate'. 🤷♂️ Enjoy!
Plans are available on my Etsy here - bit.ly/TenonJig
The initial production run of the flat-pack 10MW LTJ is already spoken for. Register your interest for subsequent production here - bit.ly/10MWLTJ_register
.
NB: this is not a pre-order, there is no commitment to purchase; you’re simply adding your name to a list to be notified when available.
+++++++++
Become a 10 Minute Workshop KZfaq Member for exclusive content - bit.ly/10minuteMember
Visit my Patreon channel for exclusive content - / 10minuteworkshop
Support the channel directly - bit.ly/donate_to_10minuteworkshop
+++++++++
Other videos mentioned in passing:-
10 years of Domino P1 • 10 Years of Domino Par...
DIY Peanut Jig • DIY Peanut Jig [**Gift...
Strong, or Strong enough? • Strong? Or Strong enou...
5 Festool gamechangers - • Four Festool Game-chan...
+++++++++
If you’re looking for a few gift ideas then take a look at my Etsy store, my Amazon Affiliate store, or any of the links below.
My Etsy - bit.ly/10minuteShop
Amazon store - bit.ly/10minuteworkshop
My ‘social’ links & contacts in one place - bit.ly/10minute-links
Full list of ‘Stuff I use’ at Full list of ‘Stuff I use’ at www.10minuteworkshop.com
Connect with me on twitter @10minuteshop
Connect with me on Instagram @10minuteworkshop
+++++++
Heads up; as an Amazon Associate, and an eBay Partner Network member, I earn from qualifying purchases made through these links.
Wherever possible links are to actual products used, but this is not always possible e.g. some products are not available in the US, so something [similar] has been linked to instead.
Amazon UK - www.amazon.co.uk/shop/petermi...
eBay UK - bit.ly/Buy_eBay_UK
++++++++
Used/featured in this video:-
Strawbyte waste side jigs - bit.ly/Strawbyte_jigs
Trend T4 router - amzn.to/3ckBOF8
Spiral upcut bit - www.wealdentool.com/acatalog/...
18mm guide bush - amzn.to/3oiTchQ (US: amzn.to/341syAM)
Festool centering mandrel - amzn.to/32cYjcc
Festool OF 1010 router - amzn.to/2tBmXk9 (US: amzn.to/2tigRT6)
Festool TS55 Tracksaw - amzn.to/2pGvzDS (US: amzn.to/2oOgGhw)
Festool lever clamp - amzn.to/2pOohLD (US: amzn.to/2pnFZIM)
Festool MFT - amzn.to/2x49HHE (US: amzn.to/2J25aKy)
Festool Midi extractor - amzn.to/2tCIN3Q (US: amzn.to/2rKNIOx)
Hultafors Talmeter tape measure - amzn.to/2pHwnbH (US: amzn.to/2oqLQc9)
Moldex 6810 in-ear defenders - amzn.to/2P2c5nP (US:amzn.to/2LgIsye)
Mirock square - etsy.me/2MC0RT
Mirock 500mm T-ruler - etsy.me/365P0KE
Bahco 6” combi square - amzn.to/2oumhX4 (US: amzn.to/2ouSg9k)
+++++++++

Пікірлер: 609

@Maocul1906 3 жыл бұрын

Absolutely interested in the flat pack version!!

@-abigail 3 жыл бұрын

I travel to job sites with all my tools on public transport. Having a flat pack version that fits in my rolling toolbox would be very cool and seriously increase my quality of work :)

@danthechippie4439 3 жыл бұрын

You have to give to Peter, he never takes credit for an idea that isn't his even if he improves the idea itself. Peter always give credit to the person who had the idea first.

@10MinuteWorkshop 3 жыл бұрын

Thank you. 🙌 👍

@handymadness 3 жыл бұрын

Agree. Peter is just the best!

@macbaar6073 3 жыл бұрын

A gentleman...

@phildando5640 2 жыл бұрын

That is one of the things that brings me back here. A wealth of original knowledge, but if something is a derivative, or an improvement on other work Peter is super transparent about it 👍👍

@Jys71208 3 жыл бұрын

Peter, you have a great presence, should have your own network TV show.

@10MinuteWorkshop 3 жыл бұрын

Ha, thank you! 👍🙌

@curtevans6151 3 жыл бұрын

The flat pack is what was going through my mind when you started creating the jig! Yes, very interested.

@georgenewlands9760 3 жыл бұрын

Brilliant Peter, as a DIYer, I struggle to justify the cost of a Domino but this jig looks like just the thing I’m looking for. I have the router, all I need is a little bit of ply and a couple of spiral upcut bits👍

@bigmonkey999888 3 жыл бұрын

Hi Peter, yes a flat pack sounds inviting, simple ideas are often the best! Steve

@AchimTheEagle Жыл бұрын

By far the best DIY Loose Tenon Jig I've seen so far! 10/10

@carlobesenzi9325 3 жыл бұрын

The simplest ideas are often the best! I'd be interested in the flatpack version please!

@allanbeasley4565 3 жыл бұрын

I’d be interested in the flat pack jig. Great idea!

@matthewdartford9501 2 жыл бұрын

As soon as the vid started and I saw the jig for the 1st time I could immediately see how it works....so simple. And amazed that this is the 1st time Ive seen it. Excellent stuff

@davidsneddon2242 3 жыл бұрын

Peter you have done it again, blown my mind with the efficacy of your delivery of both the idea and the video, fantastic idea and what a brilliant collaboration. Definitely interested in the CNC Flat Pack.

@10MinuteWorkshop 3 жыл бұрын

Thanks David! 👍

@chrismcandrew1041 3 жыл бұрын

Absolutely interested in the flat-pack version. Yay!

@mick882 3 жыл бұрын

Brilliant Jig Peter and Gordon. Deffinitley interested in the flat pack version. Count me in.

@eyuptony 3 жыл бұрын

Well pointed out Peter using the little bandsaw jig to align the inside face of the plywood jig in the correct position on assembly. I like this well thought out simple designed jig, its relatively easy to make and use with instantly good results as you've shown. Tony

@ralphrowlands3902 2 жыл бұрын

Absolutely fantastic video of one of the best jigs I have ever seen. Brilliant Peter and well done Gordon. Flat pack is a grand idea.

@OleJazzEra 3 жыл бұрын

British ingenuity is not dead. Best thing I've seen since Concorde. Put me down for one. I can taunt my Swedish friends with it... Stig-håkan: "How did you make this? Me: "Flat pack, so I need never buy another wobbly bookcase". Peter, thanks for keeping me sane through Covid.

@10MinuteWorkshop 3 жыл бұрын

Thank you! 🙌👍👍

@Tuxedo2680 7 ай бұрын

I love the idea of that spacer jig for the Festool track saw. Allows one to set the track on the "wrong side" of the cut without losing a blade width's worth of material. Brilliant!

@paulwhealy5243 3 жыл бұрын

Brilliant design - well thought out for multiple uses! From Canada - VERY interested in the flat-pack kit!! You had recommended the star byte off-cut spacers to me. Thanks for that. Absolutely love them - used just about every day. I used to try and juggle my larger pieces of plywood so the ‘keeper’ piece was always under the rail. As long as blade is sharp the ‘outside’ cut has a clean edge as well.

@roman2374 Ай бұрын

I am so happy I found this video! My 2 takeaways: 1. I will not buy a Festool domino 2. I will buy an MFT table

@paulsaxby7579 3 жыл бұрын

Yes Please, definitely interested in the flat packed version. Great video, thank you for your inspiration.

@jaffer6 3 жыл бұрын

Flat packed version sounds awesome. Great work both of you 👏

@freddieleethompson3536 3 жыл бұрын

2:50 Thank you for that link. I’ve been trying to find the hole cover for my Makita plunge saw. Top gent 👏🏻

@georgebevan9058 3 жыл бұрын

Yes definitely interested in the flat pack version!!

@johnsmit9309 3 жыл бұрын

Thank you Peter. Just watched your video a couple of times to get inspired.

@richarddalton7085 3 жыл бұрын

Awesome idea! What a clever bloke Gordon is 👌🏼

@10MinuteWorkshop 3 жыл бұрын

Absolutely! 👍

@lollybolly1000 3 жыл бұрын

Great video Peter, much appreciated. I would be very interested in a flatpack version too. Thank you.

@jb21749 3 жыл бұрын

Thanks Peter. I have a Makita 1/4" router, and got it all from eBay. Many Thanks. This rookie is going to have fun!

@bryandavies6074 3 жыл бұрын

Simply brilliant. Brilliantly simple. Thank you - and Gordon.

@TheShanehurley 3 жыл бұрын

The simplest ideas are always the best. 100% interested in a fat pack jig. 👍👍

@rhyswilliams1998 Жыл бұрын

Thanks so much for this Peter and Gordon. I’ve made a ropey version of this (first project on table saw so cuts aren’t great) but it is still good enough to allow me to join lengths of board together flush. For cabinet doors. Will probably make a neater looking version again.

@toddwilliams254 2 жыл бұрын

Greatest, simple, loose tenin jig on the market. I'd buy a flat pack kit in a heartbeat!

@10MinuteWorkshop 2 жыл бұрын

Thanks! It’s coming… 👍

@Sol-hl2rj 3 жыл бұрын

Great idea and execution! A flat pack jig is absolutely interesting.

@paulmaryon9088 3 жыл бұрын

AS always excellent thanks Peter, makes my Friday getting home from work to another Peter M vid!! Stay safe and well, 'a nice cup of tea and a biscuit' how very British!! haha

@lawman1965 3 жыл бұрын

This looks great. I have bought the plans but I would also be very interested in a flat pack kit. I'm very new to wood working but I can see other applications such as making table tops etc. Excellent idea.

@Bill.L.Carroll 3 жыл бұрын

Bloody brilliant idea and yet so damn simple! 👌🏽 Awesome colab, fellas. 👍🏽

@freddiedoyle472 2 жыл бұрын

I must wave watched this video 10 times ... I can't wait to get my hands on one of these ! Sure I could just make one .. But this is a nice way to throw Peter a little support. Thanks for all the great content Peter

@zachmathew4320 3 жыл бұрын

Amazing, I'm going to have to make one of these to try it out. Also, I can't believe I never knew about those waste side jigs - just the thing I need!

@SkillBuilder 2 жыл бұрын

yes for the CNC jig

@shaunoffshotgun 3 жыл бұрын

I’d be definitely interested in the flat pack version!

@rainerl-h259 3 жыл бұрын

again a typical Peter Millard design. Practical and handy and inexpensive . Thanks for sharing!

@grahamsquared 3 жыл бұрын

Absolutely brilliant! Certainly interested inthe CNC version pending price, of course. Good work lads.

@Alex_P_19 3 жыл бұрын

Another yes to the flat pack, or cnc plans for it for those of us far away

@idlersdream826 3 жыл бұрын

What a brilliant & simple idea, excellent work from both of you 👍

@raywood9444 3 жыл бұрын

Yes, absolutely interested in the flat pack version

@chrisallen57 3 жыл бұрын

I have been looking for something like this. Definitely interested in the flat pack!

@arcdraw 3 жыл бұрын

This is an amazing design. Thanks for sharing! I’d be interested in a flat pack version if available

@barrydoxseyuk 3 жыл бұрын

That is so good, when you have multiple carcasses it will earn its keep the first day. Parts can be interchangable or replaced so long as the original planks are the same size. Ace. O and to those that look around the ply can be found as off cuts.

@billyonions1642 3 жыл бұрын

YES to the flat pack version !!

@luispayen7822 3 жыл бұрын

Great video Peter ! I would definitely be interested in the flat pack jig set Great idea.

@mikewood3334 3 жыл бұрын

Yes indeed, a flat pack version would be great!

@shaneseth973 3 жыл бұрын

Thank you Peter. Definitely would be interested in a cnc’d flat pack

@LonghornWorkshop 2 жыл бұрын

Great idea Pete, so simple yet very effective.

@dalailager 3 жыл бұрын

Yes to CNC flat pack! That is a great jig, I,ve been using several based on Jenn’s Mistake ‘s version, but no mid-panel slots with that one

@davidhull1610 3 жыл бұрын

Genius! I think that a flat pack version of this would be good....go for it.

@10MinuteWorkshop 3 жыл бұрын

Thanks! 👍

@kennywoods8713 3 жыл бұрын

Thanks for showing Peter, I'd be interested in a flat packed version

@adhafer4542 3 жыл бұрын

You never fail to amaze me Peter!

@S.JCarpentry 3 жыл бұрын

This is an interesting idea. I'll definitely be interested in a flatpack version, might just tie me over until I get a domino

@kenzokan167 3 жыл бұрын

There are always people out there looking to 👎 things, but I can't figure out who came to Peter's channel, saw what this was about, watched it, and still gave it the thumbs down...? Love your work and big ups to Gordon - simple/genius.

@10MinuteWorkshop 3 жыл бұрын

Haha, thanks Ken! Honestly, I never notice the dislikes these days - life's too short to fret about that stuff! 👍

@steveriggsartandanimation8473 Жыл бұрын

Cannot justify the price of a domino from Festool. This is great, I shall defo be building one....

@garlicbad 3 жыл бұрын

Wow Peter, what a brilliant jig you made! More than brilliant I must say!

@10MinuteWorkshop 3 жыл бұрын

Thank you! 👍

@sewob147 3 жыл бұрын

Plans purchased. Definitely a saleable item; up here in Yorkshire there's a thrifty potential when balanced against the purchase of a Domino which must not be overlooked!

@Simon-kh2dd 3 жыл бұрын

Congratulations Gordon!

@richiesands894 3 жыл бұрын

Amazing and so simple! Can just make as many jigs as you need....Hilarious on F.O.G.. immediately changing the subject as the precious Domino suddenly becomes obsolete.. haha well done.

@samhardman6564 3 жыл бұрын

I would be interested in the flat pack version for sure. Great little jig

@DonGerico 3 жыл бұрын

I'd buy flat pack for sure. Great concept.

@trevorburford-reade8685 3 жыл бұрын

Very nice. It looks as quick as, or quicker than, the domino - especially if you might be new to the Festool. I'd be very interested in a flatpack version. Perhaps you could also include pre-drilled guide pin holes.

@larrycurran7005 3 жыл бұрын

Great idea at a great time. Was saving up for a DF 500 and kit. Then my wife's health deteriorated and expenses went way up. The flat pak CNC would be an excellent replacement for the DF500. Price is not an issue as you have always been fair with that. Work with 12 and 18 mil, 1/2" and 3/4" material so would take a flat pak for each if and when available. Great design and build teamwork. Keep up the good work!

@10MinuteWorkshop 3 жыл бұрын

Thanks Larry, and very sorry to hear about Mrs Cs health. Hope she's on the mend. Best wishes, Peter 👍

@billymacmakes 3 жыл бұрын

I really do need to get some of those 'waste side jigs' - they look so handy to make those cuts quickly and accurately! Great looking jig btw.

@10MinuteWorkshop 3 жыл бұрын

Thanks! And yes, the waste side jigs are brilliant! 👍👍

@davidcairns3203 3 жыл бұрын

Bought Strawbyte jigs on PM’s recommendation. Brilliant - use them all the time

@ashhugh8395 3 жыл бұрын

Great, definitely interested in the flat pack.

@dmc6807 2 жыл бұрын

I could never warrant the purchase of a Domino however I would certainly buy a flat pack alternative. Informative as ever thanks Peter

@10MinuteWorkshop 2 жыл бұрын

Thanks! They’re coming…! 👍

@lobbylobbster 3 жыл бұрын

Definitely interested Peter, very clever idea 💡👍🏼

@derekgranger8228 3 жыл бұрын

Love this, I'd be interested in the cnc flat pack too

@woodbe5311 3 жыл бұрын

I used this method almost 20 years ago to open mortice holes in MDF and ply. it was a good method till Domino´s comes out to the market. Now i use same method to aply hinges in doors. :)

@10MinuteWorkshop 3 жыл бұрын

Thanks Alistair! No aggro really shipping to the EU; been sending my clamp guides out since the start of the year, no worries. 👍

@johnclapham2558 3 жыл бұрын

Great Idea - very interested in CNC flat pack version. Thoroughly enjoyed the video as always

@10MinuteWorkshop 3 жыл бұрын

Thanks! 👍

@paulgarriock3898 3 жыл бұрын

Hi Peter. You recently mentioned a series on routers, how to use them etc. Just saying... that would be VERY interesting to me (and I imagine lots of other folk out there.

@RellikNev Жыл бұрын

Absolutely brilliant. Perfect for those of us who could never afford a Festool domino tool. I would definitely be interested in a flat pack kit.

@10MinuteWorkshop Жыл бұрын

Thanks! Flat-pack has been available for over a year, in two different versions. Store should be directly below the video, or at 10minute.shop 👍

@Ole.Rellik Жыл бұрын

@@10MinuteWorkshop Thanks for pointing that out. Don't know how I missed it.

@kenjohanning1163 3 жыл бұрын

I would definitely be interested in a CNC flat pack.

@VideoPixelStudio 3 жыл бұрын

Yes, def interested in a flat pack one!

@ChrisMurley 3 жыл бұрын

Great vid. Would definitely be interested in a flat pack version.

@abdullahali5039 Жыл бұрын

Hi The work is very excellent and I wish you safety and success my regards Abdullah from the State of Kuwait

@craigstreet6067 2 жыл бұрын

+1 for the flat pack jig, thanks!

@10MinuteWorkshop 2 жыл бұрын

It’s coming! 👍

@jjbuzard 3 ай бұрын

Excellent Jig! Just saved me some money by not having to buy a Fancy $$$$$ machine, love the design and the possibilities! Your presentation is wonderful! I did subscribe and look forward to future ideas from you!👍👍👍👍👍!!!!!!!

@hugebone3853 3 жыл бұрын

yes please to the flatpack, genius!

@MorgStar44 3 жыл бұрын

Great Video Peter, flat pack jig yes pls :-)

@alistairbiggar6830 3 жыл бұрын

Fantastic design and video...definitely interested in the flat pack version. I am going over the strawbyte to get some waste side jigs now, brilliant idea.

@10MinuteWorkshop 3 жыл бұрын

Excellent, thanks! 👍

@davidashurst3242 3 жыл бұрын

Peter, Would be really interested in a flat pack jig and once again thank you for sharing your expertise and knowledge. Best wishes, Dave .

@10MinuteWorkshop 3 жыл бұрын

Thanks Dave!

@keithstanley2007 3 жыл бұрын

Yet another EXCELLENT video. MANY THANKS!!!

@10MinuteWorkshop 3 жыл бұрын

Thanks! 👍

@nicolasadams3186 3 жыл бұрын

Another great video. Definitely interested in the flat pack when available.

@abcaabca6364 2 жыл бұрын

That Strawbyte waste side jig is nothing less than brilliant. Never thought of using the tracksaw as a radial arm saw (or very wide cross cut saw).

@brianhill1294 3 жыл бұрын

I’d be interested in a cnc flat pack jig… brilliant idea👍

@Stuart_MM7SHX 3 жыл бұрын

I'd be interested in a CNC flat pack!

@stevejenks2504 3 жыл бұрын

Count me in for the flat pack version. Great video, great jig.

@10MinuteWorkshop 3 жыл бұрын

Thanks! 👍

@jimpike3489 3 жыл бұрын

Hi Peter, great jig, I j have seen a few on KZfaq during the past 6 months but none look as straight forward as yours. Well done to you and Gordon, I would be interest in a flat pack version. Thanks for sharing

@10MinuteWorkshop 3 жыл бұрын

Thanks Jim! 👍

@duncanmcinnes5819 3 жыл бұрын

Great idea, would definitely be interested in a CNC flat packed version.

@jaywright3376 3 жыл бұрын

Love the idea.Flat pack version please.

@tig1958 3 жыл бұрын

Thank you for another great video. I am also interested in a flat pack jig.

@davidcairns3203 3 жыл бұрын

Sign me up for the flat pack version! Such an elegant way around the ever rising cost of a Domino!

@dannycutter7937 3 жыл бұрын

Genius idea I'd be interested in a flat pack version

@steveparkes1266 3 жыл бұрын

Absolutely great idea Peter. very interested in a flat pack version, please let me know if you go ahead. Once again great video and thanks for sharing 👍

@10MinuteWorkshop 3 жыл бұрын

Thanks Steve! 👍

@mjjf8297 3 жыл бұрын

Flat Pack, yes please