Ultimate SMART SWITCH Buying Guide

Рет қаралды 32,089

Күн бұрын

Recommended budget WiFi switches (Neutral wire required)
Kasa / TP-Link - amzn.to/35GWKW7
Amazon Basic Smart Switch - amzn.to/35GWKW7
Wyze - amzn.to/3J6282V (Doesn't work with 3-way switches)
Wemo - amzn.to/3NPMfkM
Treatlife - amzn.to/3KbFh77
No Neutral Required options
Lutron Caseta - amzn.to/3DIE05g
Cync (formerly C by GE) - amzn.to/3ua3SDQ
Inovelli Dimmer - amzn.to/3uYxOCg
Hub Required
Jasco/Enbrighten - amzn.to/3DMi89g
Zooz - amzn.to/370JDQd
Inovelli Red Series - inovelli.com/products/switche...
Aqara - amzn.to/3jaLLay
Smart Bulb Control
Lutron Aurora (Friends of Hue) - amzn.to/3r44M2G
RGBGenie - amzn.to/3J62era
Wyze - amzn.to/3J6282V (Wyze Bulbs only)
Brilliant Controls - amzn.to/3uY7qIt
Fan Control
Lutron Fan Switch - amzn.to/3J9Pgsr
Enbrighten Fan Switch - amzn.to/3LGExHE
Treatlife - amzn.to/3LJNv6S
Homekit Compatible
Meross - amzn.to/3NJivWF
Lutron Caseta - amzn.to/3DIE05g
Aqara - amzn.to/3jaLLay
Wemo - amzn.to/3NPMfkM
Eve - amzn.to/3JgJBkm
Check out our other product recommendations - www.amazon.com/shop/hometechd...

Пікірлер: 25

@dannyburdette6629 Жыл бұрын

Option...1st I am a electrician that has worked out of the I.B.E.W L.U. 466 for 32 years. That being said I want to inform people that if your neutral and ground are bonded in your electric panel you can use the ground as a neutral for switches that require a neutral. I have wired switches this way in my brothers, my mother's, my cousins house and my own house. If you don't have a disconnect box inline before your electrical panel then your ground and neutral WILL be bonded.

@prevaloir5362 Жыл бұрын

I just took the safe route and got a no neutral switch for the 1 box in my house that didn't have a neutral wire

@tinasewell1604 2 жыл бұрын

Moesgo is an option for no neutral wire. We have just one bathroom with no neutral wire and I was able to use moesgo to set up smart switches. Cost me about $35.

@ronm6585 2 жыл бұрын

Thanks.

@Skeetersbuzz 3 ай бұрын

Leviton Gen 2?

@TylerMorton 2 жыл бұрын

Would you recommend any of these for a pool pump (obviously in a weatherproof box)?

@BrandonDoyleMN Жыл бұрын

You'd just need to make sure it's rated for motors

@Frnkgrimes Жыл бұрын

Can Aqara hubs/sensors control automations that end with a Lutron switch? For example, through homekit?

@BrandonDoyleMN Жыл бұрын

Through an intermediary such as HomeKit they should be able to.

@BimmerWon Жыл бұрын

Do you know of any smart switches that control wall receptacles and won’t fry when I accidentally turn them on with a 1150 W vacuum cleaner plugged in?

@BrandonDoyleMN Жыл бұрын

I’d go for one that is rated for large loads like fans, it will likely need a neutral wire. There’s a version of Lutron that comes to mind, and probably something from manufacturers like GE. Alternatively you could change out the outlet. in general I’m not a fan of switches that control outlets, when we built our house I made sure they didn’t put any in

@BradHighlandTapSnap1114 Жыл бұрын

Thanks for this video. I purchased 3 Wyze smart switches. I have a 3 gang box in my bedroom. 1st switch controls ceiling light on/off. 2nd switch controls ceiling fan on/off. 3rd switch controls closet light. All switches are on same circuit. No switches are 3 way. Load comes into 3rd switch. Then jumps from 3rd switch to 2nd switch and then jumps from 2nd switch to 1st switch. Each switch has line out going to respective fixtures. I followed same configuration on new Wyze switches that I had on old dumb switches for load and lines. Neutrals wires are all bundled and then pig tailed to each Wyze switch. Same with grounds. The Wyze switches will not power up and the LED lights are not on. I do have power though at each load. Will the Wyze switches not work with this configuration? Can you recommend switches that will? Thanks so much!

@BrandonDoyleMN Жыл бұрын

I'd recommend having an electrician take a look, I've always had separate line/load wires for each circuit in the installs I've done but I'm not an electrician.

@BradHighlandTapSnap1114 Жыл бұрын

@@BrandonDoyleMN Thanks, I appreciate your response.

@justinbenc Жыл бұрын

You have it configured wrong - it should work. Load is the connection going to the light, so please make sure you're not connecting that to the line part. Line could connect to one light and jump to other switches. I would use a multimeter to confirm if its the line wire (if this isnt solved yet - i see its been 2 months, lol)

@thegrimeyone181 2 жыл бұрын

Which one of these switches work with LED bulbs, thank you

@UGotTheFunk Жыл бұрын

Any switch will work with an LED light bulb.

@robertolopez-ibanez6354 Жыл бұрын

Are there any 3 gang 2way dimmable smart switch? Thnx

@BrandonDoyleMN Жыл бұрын

You can do multiple smart switches in a box, I've got multiple sets of 3 lutron caseta dimmers in a 3 gang boxes around the house, some 2 way, some 3 ways. You can do that with most switches. Brilliant does have an option that'd take up the whole box and does dimming

@robertolopez-ibanez6354 Жыл бұрын

@@BrandonDoyleMN thnx

@jimwilcox946 Жыл бұрын

If a new build has PoE lighting (because of cheaper wiring and lower electrical usage) is there any manufacture of traditional style light controls that also work with PoE? I plan to have a several touch screens around the house that integrates all smart devices in addition to the lighting, but I still want traditional light switches by the door, bedside, etc. for practical purposes (guests, children, or when I cannot find my glasses).

@BrandonDoyleMN Жыл бұрын

I've seen Crestron systems with low voltage touchpads for switches, you could possibly use buttons or relays to do this. What company is providing the PoE lighting and what do they recommend for control?