UMC202HD How to easily set up

Рет қаралды 165,880

7 жыл бұрын

How to set up hardware and software of U-Phoria UMC202HD USB soundcard for zero latency ultra quiet phantom powered audio. Support the channel, sign up or purchase one of our courses here:
www.buymelikeme.com/

Пікірлер: 168

@quirkypurple 5 жыл бұрын

Of all the videos I watched, this was most informative. Thanks and good delivery; to the point and clear.

@bionikpulse Жыл бұрын

this is a great device

@boneburied 5 жыл бұрын

Thank you for making it simple. Very informative and I am more likely to listen to you over others as you do a great job explaining it in detail.

@buymelikeme 5 жыл бұрын

Thank you for your comment. It's very much appreciated. This should be the standard for all future videos.

@lartensgrill6106 3 жыл бұрын

Never knew you could fit in an xlr male end into the input sockets! Very useful video, thanks

@MyJeanf 5 жыл бұрын

Excellent video, I have just purchased the umx22 but after watching this very informative video might return it snd get the UMC202. Thanks jF

@Foreverarti 4 жыл бұрын

That jingle was legendary lol good vid too man,much appreciated.

@martinlewis2143 3 жыл бұрын

Great video! Thanks for helping me sift the audio interfaces with a wonderful jingle to entertain!!

@mythreefoundation4109 4 жыл бұрын

thank you so much. i was struggling a lot and i tried everything but then i saw your video and realized that i hadnt turned on my soundcard. lmao thank you :)

@buymelikeme 3 жыл бұрын

Glad to hear that

@BOOMBABY2020 2 жыл бұрын

hey followed the video and hey you got my mic working ....great job thanks

@GRBAquatics 2 жыл бұрын

Thankyou for your Comprensive review and Demo. You have convinced me to get one. Cheers

@buymelikeme 2 жыл бұрын

You're welcome m8.

@GuitarBoi 5 жыл бұрын

Please help, I’m trying to use it for amplitube 4. I installed the drivers and so far my guitar signal sends through to my laptop but I can’t hear anything. I’m plugging my headphones into my laptop but I’m fine with audio coming from the laptop speakers too. Help pls

@Chicletstar 4 жыл бұрын

My dynamic mic doesn't turn the signal green when his gain is low like you just showed on minute 4:45 . I've been watching a couple of videos to try to figure out why is my output level so low (barely registers on my daw) while my gain and headphone switches are raised up so high. Is there any help you can give me on this subject?

@ErtugruLTurkaydn Жыл бұрын

Hello Sir, When I connect a microphone to the 1st input of the UMC202HD Sound card, I get it from the right when I connect the headphones to the 2nd input from the left. I have made all the sound card settings in cubase etc programs, but in general, how can I solve this problem except for recording, I would appreciate it if you could help me.

@Calvinsalvias 2 жыл бұрын

Is it only B1 mic that you can use for the umc202 interface Because am using C1 mic but it's not responding to my iphone

@MathinusG Жыл бұрын

Killer tune. More money before more honey!!! Love it. Now to work out how to set up to my dslr camera and or cellphone.

@abdalmuhsseinalhussein886 5 жыл бұрын

Hello Can I bundle with a sound mixer and how

@by_antony 3 жыл бұрын

So the unit is powered via the USB cable from a laptop? Does this mean there is an internal (lithium or other) battery inside the UMC202HD?

@mr.p3666 3 жыл бұрын

Hi sir, i do have behringer 204hd. I'm using REAPER DAW. My setup is my input is selected for my interface and my output goes for my headphone that is connected at my computer. I do here the sound from reaper but i can't play sound into my desktop as it say IT IS BEING RENDERED or USED by other program which is reaper. Is there any way that i can still here my desktop sound at the same time here my sound from reaper? Thanks sir

@mdss9117 2 жыл бұрын

Please reply can we connent 2 guitar? one in XLR and one in instrument line ? please only answer if u have tried :) and does it quality affect ?

4 жыл бұрын

*HELP' no sound device is connected to the pc 'not seeing card, cable changed, problem not resolved,is the card broken?suddenly it was like this, was not broken* helpp

@manso1721 5 жыл бұрын

Great video! which adapter do I need to connect regular headphones to the audio interface? Thanks

@buymelikeme 5 жыл бұрын

Thanks. Try this one or one like it: www.ebay.co.uk/itm/3-5mm-Female-Plug-to-6-5mm-Male-Jack-Stereo-Audio-Adapter-Converter-Headphone-3/331759298519?epid=1854991934&hash=item4d3e6527d7:g:DKcAAOSwCypWoKYq:rk:2:pf:0

@envisionedbyjay5969 4 жыл бұрын

If anyone can reply I'd appreciate it, the switch behind my Behringer doesn't want to turn on and the whole Behringer doesn't want to turn on even when I connect it, it was just working recently the other day

@mrmark41 5 жыл бұрын

Hi. Great info. What are those extension connections that you used to hook up the RCA cables from the unit, to the speakers? Thanks in advance!!

@buymelikeme 5 жыл бұрын

I used a 3.5mm Y connector jack from the laptop split into right and left/red and white RCA jacks to a set of speakers but that came out of the laptop phone socket. Please understand that the UMC202HD allows you to select it as the main sound processor via the software and choose where to send it out. That's why you never see me hook up cables on the rear.

@RexyFan 4 жыл бұрын

If i were to connect this to my macbook... do I just plug it into the headphone jack of the behringer ? Or would I need one of those cables that have the earphone jack on one end and two 1/4” jacks on the other end for left and right and plug those two ends into the input of the behringer ?

@buymelikeme 4 жыл бұрын

All the audio conversion is done via the usb cable. So if I understand you correctly all you have to do is plug it in. The device then becomes an external sound card. No need for extra cables unless you are recording through the umc202hd into the mac. You can then plug your headphones into the umc202hd.

@xTeschioPazzox 7 жыл бұрын

Hi, i can ask if behringer umc202hd has the balanced or unbalanced outputs? I hope they are balanced because I have to connect them to TRS with two active monitors. I apologize for my English, thank you.

@buymelikeme 7 жыл бұрын

Unfortunately the outputs are unbalanced only. You would need the UMC404HD for balanced outputs as well.

@nicolasgallegoarboleda3045 2 жыл бұрын

Hi, The output of The headphones are stereo or mono?

@neerajsodhi7 4 жыл бұрын

Can this be used to record in Android mobile phone?

@mklschwrtz2 7 жыл бұрын

Is it possible to use this device as a regular external sound card? I'm looking for something that I can plug my headphones and microphone into and have individual volume controls for both like I had on my old PC headset. I won't be recording anything, mostly just gaming, watching movies and sometimes voicechat with my friends while gaming, wich is why I'm basically just looking for a gain controller for both the mic and headphones.

@buymelikeme 7 жыл бұрын

You could use this as it will giive you the gain control you're seeking.

@ShreeNation 6 жыл бұрын

Do I need to turn on +48v for a dynamic mic?

@buymelikeme 6 жыл бұрын

Dynamic microphones do not need a power supply (partially true). The vast majority of dynamic microphones can manage without power but there are some exceptions. Basically, all condenser microphones need some kind of power supply. This is primarily to supply the impedance converter and for non-electret condensers to charge the electrodes (membrane and back electrode). Active dynamic microphones need a power supply as well. From: dpamicrophones.com

@AUGUSTALLEN28 5 жыл бұрын

Where did you get those output plugs that went into the speaker/monitors?

@buymelikeme 5 жыл бұрын

Ebay. If they're in store you can get them from my ebay store: www.ebay.co.uk/usr/buymelikeme If not check back on Monday.

@xstzo 2 жыл бұрын

i updated the drivers and now my mixer isnt even showing up as a device anymore what do i do?

@svrghs 4 жыл бұрын

Hi, Nice Video and explanation. Which Daw would you recommend for 202HD?

@buymelikeme 3 жыл бұрын

ACID Pro 10 or Serato Studio.

@user-jh4vf4kx4e Жыл бұрын

Thanks for your

@endofword2012 6 жыл бұрын

Hey No Power Switch OFF...? you make me convinced and i have buy one one!

@buymelikeme 6 жыл бұрын

No. Only for the 48v phantom power.

@myrio1 7 жыл бұрын

How does it work with your windows audio for eg. Can you play a youtube karaoke track and record it on track one of your daw and then lay a vocal on track 2 of the daw?

@buymelikeme 7 жыл бұрын

Yes. Take for example you have an instrumental like the karaoke track you refer to. You can place that on track 1. Open track 2 and as long as the latency in your DAW (Digital Audio Workstation) is set correctly and you have a decent pc/laptop there will be no issues.

@simoantal 4 жыл бұрын

Great video.Windows 8 64 bit good?

@justiceandyou 5 жыл бұрын

Is it possible to use this device without PC? If I do not want to record anything, just play an acoustic guitar and reflect the sound through ( Mic + umc22 + Speakers ) ?

@buymelikeme 5 жыл бұрын

So your question is can you use this as a stand alone mixer to play an instrument without a computer? No I think not as the device is powered by USB. You could power it via a usb hub plugged into the mains but it reacts only with the software via computer.

@alexmac4039 4 жыл бұрын

When you are reording vocals with this interfade, you can only hear yourself through one side of the headphones??

@ahsanchuhan 4 жыл бұрын

Alex Mac Yes, that’s because the inputs are mono tracks. You should be able to fix that in the DAW that you’re using, either by changing stereo input to mono, or using the mono channel for both the left and the right channel

@Calvinsalvias 2 жыл бұрын

Please I need you to help me set my own up in my iphone

@sempei58 5 жыл бұрын

i noticed on your desktop you had mixcraft. Would be interested in knowing what kind of recording you do using mixcraft. You have any tutorials on using the Behringer with mixcraft

@buymelikeme 5 жыл бұрын

Tried it and never liked it. Might go back to it later on though.

@balondor8053 Жыл бұрын

Please is it (SLR socket ) or (SRR socket)

@jf1859 5 жыл бұрын

I have UMC204HD 192k but i can't use it with a midi keyboard to create music using midi port to have sound on VST in a FL Studio DAW! Please i need your GREAT HELP!

@buymelikeme 5 жыл бұрын

Use USB keyboard for midi instead.

@fredvasquez4201 5 жыл бұрын

Hello, thanks for this informative video. Is it possible to connect 2 headphones at the same time?! ( for a podcast with a co-host) I just bought this interface and trying to find solutions where myself and my Mrs can her each other via direct monitor properly. What cables or devices do I need? All best.

@buymelikeme 5 жыл бұрын

As the UMC202HD only has 1 headphones output you will need the following 2 items. You can buy these anywhere including ebay or a local store. GOOD LUCK and thank you for the comment: 1. [Gold-plated Pure Copper ] 3.5mm 1/8 inch Female to 6.35mm 1/4 inch Jack Male Stereo Audio Jack Adapter Plug,Gold. 2. Gold 3.5mm Headphone Splitter Jack Male to 2 Dual Female Cable lead audio Y-SPLITTER www.amazon.co.uk/HEADPHONE-ADAPTER-PREMIUM-Earphones-Connections/dp/B007ZR1ZBE/ref=sr_1_7?keywords=6.5mm+headphone+adapter&qid=1560829178&s=gateway&sr=8-7 www.amazon.co.uk/AKORD%C2%AE-Headphone-Splitter-Female-Y-SPLITTER-Gold/dp/B00JSS8NR2/ref=sr_1_15?keywords=headphone+splitter&link_code=qs&qid=1560828653&s=gateway&sourceid=Mozilla-search&sr=8-15

@powersliding 2 жыл бұрын

worst case scenario...one headphone connects to the pc...maybe that will work..just an idea from an amateur

@hebunmehmetsirinuyar1733 Жыл бұрын

@@powersliding hello bro. Did the solution work? And in podcast is that okay to hear your own voice? Because I assume with this way you will hear your and your co-hosts voice at the same time, is that okay? Doesn’t it bother you?

@Texicus_Reddicus 4 жыл бұрын

thanks for teaching us what usb is *PHANTOM POWER IS NOT ON OF AND WILL BREAK YOU ELECTRONICS IF THEY ARE NOT COMPATABLE*

@reynaldowify 7 жыл бұрын

Hi, i wonder if it is possible to take audio out of the computer via usb, and by the umc 202 hd convert it in analog, to send it to main speakers Thanks

@buymelikeme 7 жыл бұрын

Once you connect the usb to the computer and install the drivers the UMC202 will send the digital signals out of the audio outputs on the rear of the machine. You can then connect an unbalanced stereo cable to your speakers or even your hi-fi.

@reynaldowify 7 жыл бұрын

So much thanks to you. Just bought an numark platinum dj controller, but not that happy with its audio card, so, i wondered what if i connect an extra audio interface in another usb port, in order to mix within the pc, and taking audio from this extra one. By the side, also would be very nice to have a little interface for recording, actually, have a behringer x air 18, but it is too big for carry as dj, or make simple recordings Again, thanks, did not find any explanation about this use for it

@reynaldowify 5 жыл бұрын

Just one year later, finally bought a umc 404 hd, and i can take audio out via usb, for both, main and headphones, in traktor and vdj. Serato sucks

@djadammm 4 жыл бұрын

Hey, I connected my umc204 device and I can only hear audio from daw. What I have to do, to hear audio from other apps?

@ComatoseMN 3 жыл бұрын

You probably figured it out by now, but I figured I'd reply... I'm assuming it's a windows OS, you basically Right Click on the little speaker in the bottom right hand corner of the screen, open properties, or sound settings, (Something like that), and there should be a setting where you can choose The input/output device, just pick your interface, done. If that doesn't work, follow the steps in this video, then go back over what I wrote above... >M

@johnviera3884 3 ай бұрын

there’s a LINE input mode. There’s a INST input mode. where’s the MIC input preamp mode? also, there’s no way to monitor a mono signal (one channel) through stereo headphones.

@sanchiani9717 4 жыл бұрын

hi, can you help me? i use reaper, and i have recorded several guitars, but when in device i choose UMC ASIO and when i press the play button i dont get any sound, i have to choose the FL STUDIO ASIO then i can hear what i have recorded, do you have any clue¡?

@buymelikeme 4 жыл бұрын

No! I use Acid. Used to use cakewalk but that's shit with VST's and it loves to corrupt songs.

@d-rockanomaly9243 4 жыл бұрын

Make sure reaper, the UMC control panel, and windows settings for the mic are all set to record at the same sample rate, like 48000kz 24 bit. Increase the buffer setting possibly in the UMC control panel and make sure the output and input levels are maxed in the UMC panel as well. If you still are having problems, let me know as I have the same setup and DAW. There's a lot of things it could be.

@rktrkt-tw8nd 3 жыл бұрын

What to be used to get 24 192 recording ? In audacity it records 16 192 only. How to set up ?

@talalmohammed7058 6 жыл бұрын

I have same shit but without HD!!. When i start recording it stays for 1minute then gives a wrong massage " the UMC Driver Failed " and goes away !.. please i need help !!

@ShiniRyukG 4 жыл бұрын

Hello , 13:21 what's the name of that adapter ? thanks you

@buymelikeme 3 жыл бұрын

Headphone Adapter 3.5mm Female to 6.35mm Male

@myrio1 7 жыл бұрын

Also how many discreet separate audio tracks can you lay without bleedover from another track?

@buymelikeme 7 жыл бұрын

Number of tracks is based on not just your settings but the power of your system. You have a killer system that can move the moon out of orbit, hack the pentagon or burn a hole through your desk from the cpu heat you should have no problems. You have a slower system 4 to 8 tracks before clipping or lag and hurting your wrist from banging the table. I used to experience bleedover in cakewalk, hated it. Switched to acid pro, changed a few latency settings and got a faster hard drive really helped.

@marketweis 3 жыл бұрын

You voiced most of the video on the B1 and the UMC?

@buymelikeme 3 жыл бұрын

Yes!

@TheMerlinshawk 5 жыл бұрын

nice video I have the same but have a problem, I cant get volume when recording what is the problem

@buymelikeme 5 жыл бұрын

What software program are you trying to record with? You have to make sure that the UMC Driver is selected in options. If you're using an external mic or other equipment check that they are on and have the volume up and watch for a signal on the device.

@TheMerlinshawk 5 жыл бұрын

hi thanks for your reply, im using sonar platinum, umc is selected but im not sure if my sound device is set right even with the volume full up it hardly shows on the meter, I should be able to hear myself singing with the backing tracks which are playing ok@@buymelikeme

@buymelikeme 5 жыл бұрын

@@TheMerlinshawk I used to use Cakewalks stuff but found it unstable, that's what it was called before it went from midi to an audio workstation. Make sure the track that the vocal is going to is armed. It will not show you anything let alone record if the armed/record enable button is not pressed before recording begins. If that fails save your project open a new project and set up 1 track and try to get audio onto that track. Also make sure that the UMC202HD's 48v phantom power switch at the rear is on.

@shubhamkindre4618 7 жыл бұрын

my pc is enable to detect the audio interface..i have installed the right driver..i have pluged and unpluged the audio interface plenty of times now..what must be wrong? help!

@buymelikeme 7 жыл бұрын

If you look below at the comments I spoke to Maysinator Smith, he had a similar problem. Unfortunately he could not find a solution. HOWEVER, notice if you will he had windows 8.1. I'm using Windows 10. Perhaps it is your operating system. If you have another machine/laptop try it on that with Win 10.

@shubhamkindre4618 7 жыл бұрын

thankyou for replying. i fixed the problem reinstalling the driver and restarting my pc .Incase anyone here needs this. (y)

@buymelikeme 7 жыл бұрын

Good job. Enjoy!

@elmeddinhuseynli492 7 жыл бұрын

hi, what do you recommend for me? i want to create a small home studio, which one is more preferable? xenxy qu 50 mixer or the device you show in this vidio.?

@buymelikeme 7 жыл бұрын

From my point of view I wanted something small, reliable and high quality that was much quieter than the in-built mixer carrying the background noise of the laptop for vocals, and the UMC202HD was perfect. Tried usb mixers and the noise floor was not that quiet so that killed that argument. For a studio where music instruments and other artists/vocalists are involved and you will be using more than 2 mics, get a mixer. For example, if I was going to upgrade I would get the behringer 404HD, more inputs/outputs.

@elmeddinhuseynli492 7 жыл бұрын

thanks a lot for your response. i believe, it will be so usefull for me

@elmeddinhuseynli492 7 жыл бұрын

are there big difference between HD and analog recording?

@buymelikeme 7 жыл бұрын

About 5 - 10 years ago home recording software like cakewalk for HD recording wasn't that good, meaning there was a lot of clipping and other undesirable artefacts present in the audio. Both hardware and software has improved to where you can professionally broadcast from your bedroom or garage. So HD has impressed me to the point where everything you hear in this video is digital. So yes HD is better, quieter, cleaner and when dealing with transfers of data between mediums faster. Analogue is beautiful and nostalgic but HD is now the future.

@elmeddinhuseynli492 7 жыл бұрын

which one is more preferable for recording rap track? i mean HD or analog. wil i have latency problem if i buy mixer and connect it with usb connection to my laptop ,

@GGLiveSession 6 жыл бұрын

I get this pink noise like sound when I record vocals and it doesn't go away...does it have anything to do with buffer rate?

@buymelikeme 6 жыл бұрын

I used to get similar noise in Sony Acid Pro on a decent laptop. There may be several buffer settings in your audio software dealing with latency offset and track buffering. Adjust them independently until you get a clear recording. All else fails take a break, shut down system and start again.

@GGLiveSession 6 жыл бұрын

Alright thanks...do you mean buffer settings on my audio interface or daw?

@buymelikeme 6 жыл бұрын

DAW.

@GGLiveSession 6 жыл бұрын

Please how do I do that on cubase sx?

@buymelikeme 6 жыл бұрын

www.steinberg.net/nc/en/support/knowledgebase_new/show_details/kb_show/audio-card-latency.html

@vterpan 5 жыл бұрын

I've seen 3 set up videos for this and nobody shows how to connect monitors to this

@buymelikeme 5 жыл бұрын

15:45 - Shows exactly that. Most people only use it for the conversion of the low quality laptop audio to the UMC202HD for the high quality audio out.

4 жыл бұрын

@@buymelikeme HELP' no sound device is connected to the pc 'not seeing card, cable changed, problem not resolved,is the card broken?suddenly it was like this, was not broken helpp

@buymelikeme 4 жыл бұрын

@ Did you install the software? If so restart the machine with the device connected. Sometimes as I found out recently it depends WHICH USB port you plug it into. If that doesn't work right click on the start button, scroll down and click 'Device Manager'. Take a look on that list for any driver errors.

@rampmony 6 жыл бұрын

What's that second voice in the background?

@buymelikeme 6 жыл бұрын

The pre-recorded audio of me moving the camera around.

@endofword2012 5 жыл бұрын

Phantom power.... lol

@carlosortiz9913 6 жыл бұрын

How can i connect this to ableton help

@RexyFan 4 жыл бұрын

Carlos Ortiz Any luck figuring this out, since you posted a year ago? I too am in need of this answer.

@nonames8335 5 жыл бұрын

Can output connect to microlab?

@buymelikeme 5 жыл бұрын

If microlab has phono inputs then yes. Just look at the connectors, they should either be 1/4 inch male or female or 3.5mm stereo. Once you know you can get the right cables.

@spaceorbison 7 жыл бұрын

I had a problem with Focusrite also the stupid headphone jack only plays sound on one side of the headphone and you gotta wiggle the jack around until sound comes out on both sides of the headphones, really frustrating when you're trying to record and not move your head trying to avoid the chord from moving... pure shit. Ordered a 404HD they look and sound solid so far from reviews.

@buymelikeme 7 жыл бұрын

In a sound test online Focusrite noise floor/background hiss, played slightly quieter. If however the build quality is less customers will be upset eventually. Behringer at least in this instance seems to be solid trusted German audio tech.

@dongdelacruz1250 5 жыл бұрын

Nice info. But i hear zombie 2:12

@buymelikeme 5 жыл бұрын

Ha ha! Day of the dead.

@saintg1121 5 жыл бұрын

Lol

@HiTasso 6 жыл бұрын

How to connect the output?

@buymelikeme 5 жыл бұрын

15:45

@ShiniRyukG 4 жыл бұрын

@@buymelikeme Whats the name of these adapters? thanks

@buymelikeme 4 жыл бұрын

@@ShiniRyukG Hey buddy, they're called phono plugs.

@eddyhaze8239 6 жыл бұрын

I had nothing but problems with the driver with my windows 10.. did not like it at all. plugged into computer a small window pop up like it was going to install or setup or something than was gone I had to go some were so I shut down computer it took like 5 min. to shut down it's always like 5 sec. ..I came back home turned on computer and nothing no desktop just a blank screen took me a few hours to get computer back up installed driver for it and never could get the unit to work like it should .. than was on a youtube video trying to figure out how to set it up right going through the steps than the video froze I could no longer watch the video or any videos until I put back the audio settings...I give up ..not sure whats going on.. removed driver and computer is back to normal......skylake.. I7........16 gigs.of ram ..gtx 1060

@buymelikeme 6 жыл бұрын

Another user below 'shubham kindre' had the same issues. He said: "i fixed the problem reinstalling the driver and restarting my pc .Incase anyone here needs this."

@buymelikeme 6 жыл бұрын

Did you manage to figure out what the issue was? I notice that not every setup with the UMC202HD is the same. Some people pass their unit through amps, computer systems, mixers etc. Solution might be rearranging your playback and recording devices but I don't want to give you more problems. Right click over your audio speaker icon on the taskbar, select playback devices and play around with making different devices default, then try that with recording devices.

@eddyhaze8239 6 жыл бұрын

I got a older cheap i7 computer off of ebay got it working good ..I'm also going to try to run it from one computer to another ...

@buymelikeme 6 жыл бұрын

Good job man.

@maysinsoon8176 7 жыл бұрын

whenever i click the setup it loads to like 90% then just goes away. like nothing happenes the setup never comes up. any help?

@buymelikeme 7 жыл бұрын

1. If you have a virus checker try switching it off temporarily, sometimes they're a pain in the neck. 2. If it's a Mac you don't need an installer, it recognizes it automatically so just plug it in. 3. Make sure you have the right driver installer for your version of windows and behringer audio unit: www.music-group.com/brand/c/Behringer/downloads 4. Check your onboard audio drivers in your device manager to see if they have an exclamation mark. If so uninstall and reinstall then try again. Sometimes a driver conflict will get in the way of an install especially in this context if it's audio. 5. Check the behringer forum: forum.music-group.com/showthread.php?17893-Problems-with-U-PHORIUA-UMC202&highlight=umc202hd. 6. Let me know how you get along.

@maysinsoon8176 7 жыл бұрын

can you tell me how to get to my device manager exactly? im running on windows 8.1

@buymelikeme 7 жыл бұрын

The easiest way to get to device manager in windows 8.1 is to right click on the start menu scroll up and select device manager.

@buymelikeme 7 жыл бұрын

7. If everything is all good on the device manager try to right click with your mouse and run the driver as admiinistrator.

@maysinsoon8176 7 жыл бұрын

prntscr.com/fc4eu6 this is the device manager and i see nothing about audio drivers

@arturog.5867 7 жыл бұрын

I was angry because the driver didn't recognize the device, but when you said that the black cable comes with the UMC202HD I looked inside the box and I found it like hidden. Now my device runs. Damn, I feel so stupid now lol

@buymelikeme 7 жыл бұрын

It's good to take time with technology. Very glad to see your money wasn't wasted.

@musicalsuraj5181 5 жыл бұрын

brother tell me how to connect please

@abdelkaderkharoubi6001 2 жыл бұрын

hallo i need explication en franch if is possible thaank you

@buymelikeme 2 жыл бұрын

That's a great idea. I need to make time for this. Thanks.

@rigormoritz 2 жыл бұрын

I have little doubt all the protective film on the USB hub is still on that hub. Thanks for the PTSD

@eezdzef 6 жыл бұрын

you sound like Lennie James from back in the 2000's haha

@buymelikeme 6 жыл бұрын

Thanks for the compliment but I think my voice is sexier. ;)

@Deliquescentinsight 7 жыл бұрын

Are you still happy with your purchase? I am getting one of these for similar reasons.

@buymelikeme 7 жыл бұрын

Definitely still happy, that's not going to change. Listen to youtube and online radio through this baby. This device with a good mic and a software editor like soundforge and you're ready.

@SetiyonoNggalek 4 жыл бұрын

ya.7x ok

@HDFoxra 6 жыл бұрын

Annnnnnd I just realized how disappointed I am....Previous video i saw showed the 204 version with the midi, and here i was thinking 'OH GOD FINALLY AN ALL IN ONE THAT I CAN USE!' so then i click on this video, and realize my mistake -.-;;; don't feel like paying 80 bucks for something 'only' for the use of MIDI..... but, hopefully this 202HD can also be used as a playback device on the computer...

@buymelikeme 6 жыл бұрын

Yes it can. I push all audio through the UMC202HD.

@3three3three3three5 3 жыл бұрын

hahahah good video

@superjokerrr 3 жыл бұрын

Sounds muffled.

@blackdog.6398 6 жыл бұрын

I had a$100. For the 404 but they took my money 💰 now I have anything Dam it sucks being on a fixed income I wanted a little piece of something for myself but it looks like O-well !!.....it seems too to be futile !! And frustrating mates...

@buymelikeme 6 жыл бұрын

It is hard on a fixed income so do what you can with what you have and save gradually to get what you want. What usually happens is by the time you can afford it, the item you want is either discontinued and the only one you can get is a used one that is sold for the same money as new.

@apriljoymagic 6 жыл бұрын

Stay away from this you only get sound from one side of your headphones what a waste of my money just buy a mixer with 48 volts on it

@buymelikeme 6 жыл бұрын

Paul, I understand your frustration BUT you run this through VoiceMeeter Banana making sure that your default playback and recording audio devices are set to Voicemeeter and click mono you will be fine. Try it and you'll see.

@casmir8673 6 жыл бұрын

World of Raheem Just what I wanted, mono sound!!

@voraxe3032 9 ай бұрын

THERE IS NO USB LIES

@ScourgetheWitness 2 жыл бұрын

your pronunciation of behringer has earned a dislike.

@buminkagan3039 5 жыл бұрын

There is no midi connection for UMC202HD. If I connect my keyboard via USB mİdi to computure will UMC202HD see and recognize? Sorry for bad English

@buymelikeme 5 жыл бұрын

Yes. Remember the UMC202HD is just for audio. It's the computer via the USB and the software DAW (Digital Audio Workstation) that will handle the midi.

@buminkagan3039 5 жыл бұрын

@@buymelikeme Thank you