Unbelievable Tricks to Service Your Polaris Ranger 1000 XP

Рет қаралды 26,061

Жыл бұрын

Servicing 2020 Polaris Ranger 1000 XP. We change the engine oil & filter, Transmission, and Ft diff. Also replace the air filter and look at how to reset the service hours on the machine. You will Need a 6mm Allen's for the crankcase oil drain plug. You will need a 8mm allen wrench for the front and rear drain / fill plugs.
Subscribe ‪@TheRustyGarageandHomestead‬
/ @therustygarageandhome...
Contact me at
contacttherustygarage@gmail.com
Polaris Ranger Playlist
• Polaris Ranger
Polaris ranger
polaris ranger 1000
#polarisranger
polaris ranger xp 1000 accessories
Polaris ranger oil change
polaris ranger oil change kit
#polaris ranger oil change kit
#maintenance
#1000xp
#polaris ranger 1000 xp
#polaris ranger xp crew
#side by side
#2022 polaris ranger northstar walk around
#2022 polaris ranger xp1000 northstar
#polaris northstar sunset red metallic
#polaris ranger northstar ultimate
#Polaris 100hr service

Пікірлер: 39

@kmac556 Жыл бұрын

Thanks for the comprehensive video! 👍

@TheRustyGarageandHomestead Жыл бұрын

Thanks for watching

@avrgproductions1793 11 ай бұрын

Best service video… thank you!

@TheRustyGarageandHomestead 11 ай бұрын

Thank you. Thank you for watching.

@marcustodd3428 7 ай бұрын

You are the man. Much appreciated!

@TheRustyGarageandHomestead 7 ай бұрын

Thanks for watching. Hope it helped

@MrJohneeutah 6 ай бұрын

Good info and procedures here Mike!! …thanks a ton for making the vid!!

@TheRustyGarageandHomestead 6 ай бұрын

Thanks for watching

@ElvisUmbrella 11 ай бұрын

Thank you. I Actually have one on order and I’m big on preventative maintenance. I’m greatfull that you made this vidio

@TheRustyGarageandHomestead 11 ай бұрын

No Problem. Glad the information was helpful. Thanks for watching.

@adambyrd6634 Жыл бұрын

Excellent video! On your diff change, I was always told you should take the top plug out first and then the bottom plug to drain. The reason, if something happens and the top plug cannot be removed, you can still drive it to load it up.

@TheRustyGarageandHomestead Жыл бұрын

Thank you for the comment. I've honestly never thought of it that way. That's not a bad idea. I do keep a spare plug on my toolbox just in case one of the allens starts to get loose. I can change it before it strips out. I had a plug strip out on me years ago on a dozer, and I was able to use a zip disk to cut a slot on the plug. Once I got it cut, I was able to get an impact screw driver to get the plug loosen and removed. Alot of work for a stripped out plug.

@ssspconcepts 3 ай бұрын

Nice job on the video. Thanks for documenting the service procedure. Your 2020 model is identical to my 2023. I just received all of the supplies to do the service. Thanks again.

@TheRustyGarageandHomestead 3 ай бұрын

Hey thanks for watching, commenting & Subscribing. Glad you enjoyed the video. I know it was strung out a little and not the best quality video or audio. That was one of my earlier videos.

@larrycrevier9630 11 ай бұрын

Great video 👍

@TheRustyGarageandHomestead 11 ай бұрын

Hey thanks for the comment. Thanks for watching

@mattjohnson1504 8 ай бұрын

Very helpful video...thank u

@TheRustyGarageandHomestead 8 ай бұрын

Hey thank you for your comment and thanks for watching.

@tuckerandi 3 ай бұрын

I have a ranger XP 800 just got ot last last fall probably close in procedures I'm guessing. Just saw your channel on Kennys Open Air Aventure so I'm also a new subscriber, Im aiming for a thousand subs too but slow going lol.

@TheRustyGarageandHomestead 3 ай бұрын

Hey thanks tucker I'll sub to yours as well. I haven't messed with any 800's but I'm sure they are close to the same procedure.

@tuckerandi 3 ай бұрын

@@TheRustyGarageandHomestead Thanks for the return Sub , hopefully you'll find something you like

@grantklopfenstein 5 ай бұрын

Do you have a video of where all of the grease zerks are?

@TheRustyGarageandHomestead 5 ай бұрын

Thanks for watching. I do not, but There are only 3. Two on the rear stabilizer bar and one on the prop shaft.

@TheRustyGarageandHomestead 5 ай бұрын

The older 900's had I believe 17 grease fittings. When they made the xp1000 the beefed up alot of the bushings & bearings and made them non greasable.

@grantklopfenstein 5 ай бұрын

@@TheRustyGarageandHomestead so I have had 2 xp1000s and I can only find the two for the sway bars on the front and rear, where is the one for the prop shaft?

@TheRustyGarageandHomestead 5 ай бұрын

under the machine there should be a small hole in the plastic skid plate to access it. If not you may have to pull the skid plate. hope this helps. @@grantklopfenstein

@grantklopfenstein 5 ай бұрын

@@TheRustyGarageandHomestead is there just one on the drive shaft or two?

@freedomisntfree_44 Жыл бұрын

Things happening to my 2020 that makes me mad I didn’t buy a Japanese model.

@TheRustyGarageandHomestead 11 ай бұрын

Thanks for watching

@JamesWhite-tg4kw 9 ай бұрын

Would you care to elaborate what things are happening to your Ranger

@TheRustyGarageandHomestead 9 ай бұрын

I was confused by that comment as well. Thanks for watching James.@@JamesWhite-tg4kw

@freedomisntfree_44 9 ай бұрын

@@JamesWhite-tg4kw prop shaft u joints, wheel bearings goes dead for some reason when you first start it and back it out of the garage sometimes. It’s a 570 full-size just hit 300 hours almost 2500 miles. Those are things I’ve replaced and just noticed the lower control arm bushings Need to be replaced on the front end.

@JamesWhite-tg4kw 9 ай бұрын

Well I'm sorry to hear all that. I hope my 2023 has better parts on it 😳