Unilumin 2.6mm LED Screen Repair (Part 1)

Рет қаралды 22,413

Electronics ER

3 жыл бұрын

Unilumin 2.6mm LED Screen Repair
#Unilumin
#LEDSCREEN
#Repair

Пікірлер: 31

@mareknespechal243 Жыл бұрын

steady hands and good eyes, world champion :)

@adsdiffusion5004 4 ай бұрын

👍🙏 Video tres bien expliquée, top, merci

@hegelgutierrez9476 11 ай бұрын

Eres el mejor 💪🏼 si ke funcionó, en unos dias estaré subiendo el vídeo del proceso pero usando paper panel👌🏼

@sergiocaso 7 ай бұрын

a que temperatura soldas los led y los desoldas???

@aire-entertainment4546 Ай бұрын

How do you fix p3.9 outdoor dead pixels

@user-lg2ev2zb6m 10 ай бұрын

could you told me all the tools you use in the video please

@user-bb7he5wp6u 5 ай бұрын

many many thanks

@muhammedhammoud1587 Жыл бұрын

Good evening .. If you allow, you can tell me how the LED path and how maintenance you have a scheme

@igor-davidmateus2716 Жыл бұрын

Like, do Brasil. Aqui é galo!

@ragnhildthelmersen6830 Жыл бұрын

Why are you using trackpads? Is that for when the module is damaged under the pixel?

@ElectronicsER Жыл бұрын

Yes, when the track is damaged

@tomaspalencia877 2 жыл бұрын

How many C° and airflow did you use for the repair???

@ElectronicsER 2 жыл бұрын

I use between 300 to 350 more than that can damage the LEDs ,And the airflow is the lowest setting on the hot air. On the side part I use 300 then in the middle I use 350 C

@tomaspalencia877 2 жыл бұрын

@@ElectronicsER thanks, I'll try that settings!

@adithyawahyuputra9861 Жыл бұрын

what do you clean the remaining flux on the PCB?

@ElectronicsER Жыл бұрын

I used alcohol in a spray bottle

@mieorj9141 5 ай бұрын

In the early video, You only change 1 piece yet later you change 4 pieces..why was that??.. For some one who wants to learn any books or guidence You could share

@senthilkumar-pj2yo 2 жыл бұрын

Which flux used

@ElectronicsER 2 жыл бұрын

I used Chipquick Lead Free Solder Flux

@mehulpatel7685 2 жыл бұрын

And what is that little chip did you using..? And way and what are you testing…?

@ElectronicsER 2 жыл бұрын

I used spare LEDs and track pads to fix, then testing on test pattern to ensure LEDs are working RGBW

@vpgames1105 2 жыл бұрын

@@ElectronicsER I researched to buy this track pads but I couldn't find it on the internet, I found it better than putting the copper wire

@vpgames1105 2 жыл бұрын

I would like to know the name correctly so I can search

@ElectronicsER 2 жыл бұрын

@@vpgames1105 you cannot find trackpad online, you can find it from supplier of your LED panel from China, from manufacturer of LED.

@psmith6388 Жыл бұрын

@@vpgames1105 if you have for example Absen modules, find your nearest distributor and they will have all that.

@josejuanalberto6245 4 ай бұрын

Donde consigues los led

@mehulpatel7685 2 жыл бұрын

Way i need to use Flux..?

@ElectronicsER 2 жыл бұрын

You need flux to ensure smooth flow of solder on the metal joints. The main purpose of using flux however is to remove oxidized metal from the surfaces to be soldered, seal out air thus preventing further oxidation, and by facilitating mixing it improves wetting