I was going to say that

He just wants to make it so he can out it back it it's original state, though I would have liked to see him cut a silt out of the bottom edge of the plate or a hole.

i was thinking about that

Exactly my thoughts

Yes Next time removing that silicon is not easy. It will get messy

Actually.. it reconizes both but doesnt show 200% since the other battery will keep suplying the main battery it will stay at 100 for some time

Battery charge percentage that you see on your phone is based on a few factors but in simple terms it depends on the voltage between the battery terminals. All phone batteries have about 3.3V when discharged and 4.2V when fully charged. That's your 0% and 100% charge. You can have 2, 5 or 100 batteries connected in parallel (assuming batteries are identical) and they will have the same voltage across. Since you are doubling the capacity, you can go about twice as longer without needing to recharge. The only way to go over 100% charge is if you connect the batteries in a series, in which case (3.3 + 3.3) 6.6V empty and (4.2+4.2) 8.4V full. Which is too high and surely damage your phone.

My 5k mah Mobile btry bms handle 10k btry 3.7 v I want to upgrade

My 5k mah Mobile btry bms handle 10k btry 3.7 v I want to upgrade

My 5k mah Mobile btry bms handle 10k btry 3.7 v I want to upgrade

I still have the s4. Aftermarket parts are very cheap these days. Charging board from china are $3 at most. Edit: i have tried the double battery on the s4. Its actually easy. You stick the same s4 battery on top of each other. Then bridge the contacts on both batteries. Look it up on xda, you will find some pic examples

I think this battery info is kept in some files or firmware and only with root you can access them.

Download accu battery and you can change the design capacity

I wanna do it to my iPhone. But donno how to do it.

@@tankiman3489 you'll need to jailbreak for that, the apps I use are only available for Android, but if you jailbreak, you can find an app called "battery life" and that will allow you to reprogram the battery by adding capacity and then cycling the battery

@@tankiman3489 kzfaq.info/get/bejne/fquhhJyElZrPmWw.html&feature=shares try this one my friend

Buat lubang aja atau pakai kabel yg tipis

It looks ugly

@@markjarvillemartin4228 😭

Can you show me how i can attach a 5000mah cell to my galaxy s4? Have you video or site to indestand the mod. thanks

Make sure all of them have the same charge. If one of them is lower or higher, the current inrush will cause the wires burn

Did it work

I think hes lying thats why he didnt respond

I made too hahah

Of course that words. He's not lying, that's possible

Absolutely not. The only way for this to happen is for the motherboard to request more than 3 ~ 4 amps of the battery, which is impossible for a cell phone and even tablets. The only way this could happen is if the board are shorted.

They are in parallel **

in 0% both baterry has 3.3v and when 100% bo5h battery has 4.4v?

​@@farikkun1841 Normally 100% is 4,2v - 4,35v Max, 4.4v is too high; Min about 3,3v- 3,4v.

@@gabrielgomesdossantos5244 could you please say what is the name this wire?

Really ? How many days does full charging last?

@@tankiman3489 I can reliably get 2 days out of it

isnt s10plus has original 4100mah battery? what additional battery u use?

@@farikkun1841 the 10+ is only 4000, I used a 10,000mah cell to boost the capacity

@@mwbgaming28 Only 2 days from 14000mah battery?! with what kind of usage?

I Will not

it's parallel, when each battery has voltage as required for inputof phone, you add in parallel. When you want to double the voltage, you add in series. E.g. in flashlight, you can use 3 AAA batteries of 1.5V each in series, to get 4.5V.

How is this fake I made one