I love all your TFL videos Andre

Someone at Ford got a huge bonus for figuring out how to take a 15 minute DIY job and turn it into two hours of billable and necessary routine shop labor! Go Ford!

RIP on-coming traffic eyes, there are reasons manufacturers have different reflectors for different bulbs. Should have contacted Morimoto for a set of legitimate LED headlight assemblies that have the correct reflectors for LEDs.

Can't wait to see how those fans hold up in a off road environment.

Blinded by the light, hit by a douchebag in the middle of the night.. blinded by the light...

Placing LEDS inside reflectors is horrible, no cut off and light patterns goes everywhere blinding other drivers.

You DO NOT need to remove the grill or housings to replace with new bulbs. It's a 15 minute task at best. The drivers side has so much room, you can just reach in there and swap them out. The passenger side, you pull up on the air intake box and swap them out. We did this on our new 2020 F-250

Just add aux.lights for more light when you need it for off-road. Then you don’t destroy everyone’s corneas while driving around town.

Gonna be blinding people. Those are not design for hid/led. You need projectors in order for them to work properly.

The stock XLT headlights are an embarrassment.

they should have used Noctua fans. They'd move more air and do so dead quiet.

I’m glad someone stepped up to the plate and hooked you guys up with some proper LED’s. I put some GTR Ultra 2’s in my 2017 Ram 2500 and also had to pull the entire front end off as well. They even worked well with projector housings!

How much extra time did looking for 10mm sockets add to the overall install time?

God choice Andre. Got f150 leds in my f 150 for 5 year's now, they did never disappoint.

TFL Gang, Thanks for sharing this video. I did a very similar LED conversion with my 2019 F350 and it does take a fair amount of time and involves considerable disassembly. I was surprised by some of the additional wiring harnesses elements required in the kit, such as the Fog lights. Fog Light swap was very easy by itself. I will say that I did this for about half the price with All and Yorkim Led Lights on Amazon and was very happy with the quality. I also replaced the Front & Rear Signal and Brake LEDs and still was substantially less than the F150LED Cost.

For the guys doubting how well these lights hold up: I run headlights like these in all three of my rigs here in Alaska, experiencing down to -40° and on dirt, gravel, and muddy roads more often than paved. In my experience I get about a year before the fans start sounding awful and the bearings start going out. At around $90 a set it's a steep price, but for how bright they are in winter with only a couple hours of sun each day they're well worth it and cheaper than hitting a moose. My only time I've actually killed one of the lights was going through water just shy of the hood, and it killed one light altogether (Cougar Motor on amazon). I have had the best luck with the JDM Astar T2 on amazon. Which are very bright, and have held up the longest compared to others on amazon. If you have a pavement princess in Texas, these will probably last the life of the vehicle. Just be sure to adjust them so you're not blinding everyone.

Of course now your lights and truck are not street legal. I'd be curious to know how or if they match the DOT required light pattern at all.

$300 for set???? They're out of their minds, and anyone is a sucker for buying these retail price. Grab some Morimoto's or any Amazon brand with good trusted reviews. Nice tutorial tho!

Miss the days of the GM pin system to get headlights out. 2 pins and boom the headlight comes right out. But they should just come with better headlights, safety should be first.

Ford should be ashamed for selling a truck with such poor headlights, how much was that truck to buy,

Be careful Andre! I don't know about the 2020 F250, but most headlight reflectors are designed to reflect a specific type of light. So if your headlight reflectors were designed to properly reflect and focus incandescent light, it will not reflect/focus LED light the same way. Many of these reflectors create very bright stray light (unfocused) in bad directions that blind oncoming traffic. I almost got into an accident because of an oncoming vehicle who did what you have done. In most states, you can get a ticket for this, so pay attention to re-aiming and dealing with tray light from your headlights or you could find yourself to blame for an accident.

I’ve bought several lights from Headlight Revolution. And so far been happy. I like the side by side testing they do of brands they sell.

Boy, Tommy really is a Grumpy Gus. I thought he was just playing one on TV.

Nice video guys. Love the headlights and fog lights.

I have a 2019 Lariat and insisted on the quad beam LEDs. Only problem I have is everyone flashing their lights at me thinking I have my high beams on- even after the recall adjustment! They are super bright and I love them!!

What your calling the voltage regulator is actually a CAN Bus module, and the fog lights have a resistor. Both trick the body computer to simulate the same resistance as the original Halogen bulbs to keep from turning on the headlight out message on the truck display. You should be able to activate LED front lighting eliminating the need for the modules and resistors. A Ford dealer or a body builder should have a program to enable LED lighting. IDK about Ford, but RAM has the AlfaOBD app you can get for android, and turn LED lighting yourself.

This truck really needed this mod

Have Tommy come from the other direction in the Subaru at night, so we can get a report on how it looks from there. Since Super Duties already fry oncoming drivers with the weak sauce halogens, I expect this will be ugly. The shots at the end make it look like the hot spot is now left of the centerline....probably this is now one of those trucks that you flash your high-beams and their responding flash is briefly dimmer. I can show them some nice dark roads for the test, near my house, then dinner at their favorite Chinese restaurant .

LED's are amazing! Buuttt... Very little heat output so driving in the snow makes it fun when you have to get out and clear snow from your lights.. Cannot wait to see the results

Those lights when oem are already blinding to traffic because of outdated lighting design laws but you want to make them brighter?

Here's a plan for manufacturers, just put the better lights in everything. Surely they can cut that cost elsewhere on a base truck.

If you have just the low beam on it should light up just the top one? Or both of them? I just installed mine on my 2019 f250 lariat but didn't have resistors so I ordered some got one side only and took it off and now just the top one works on low and the other side still low n high on?

So I have a 2015 f250 and my headlight bulbs are stock still. I have been looking for brighter lights. More like LED bulbs. I am having difficulty finding a good right brand that will work for my truck and for me to see better at night. Any brands or thoughts?

I'm LED obsessed! Changed all the bulbs on my 2018 Rav4 Adventure. Accept, for the blinkers. I don't want to mess with resistors or load equalizers.

LEDs suck in the winter...ice will form on the lens because if little to no heat.

Nice upgrade! Will be interesting to see how long the fans last on those.

That process reminds me of having to swap out my headlights on my old 2013 GMC Sierra truck. Definitely not user friendly. But the light output is where it needs to be. Cross your fingers on durability.

That Chrome grill would look Awesome on my wall..look at how Huge it is!!! Nice job Andre!☺And Case

Great upgrade 👍

Morimoto xb headlight housing and fogs, the best!!

White light is not a Fog Light. Try Amber or Yellow, as a extruck driver and Exfirefighter/Engineer trust me Yellow headlights or fog lights makes a massive difference in your eye strain and the actual penetration of light through the fog.

Since the day I began to drive, about 23 years ago..., I've had vehicles equipped with Halogen Headlights and possibly some with sealed beam headlights. I've driven mostly under HPS Streetlights. I've driven under the brightest lights and under complete darkness. I've never any trouble seeing what I needed to see. If you feel that you need Super High Intensity, Blinding LED headlights & Streetlights to drive safely, perhaps you should consider NOT driving at nighttime. It's unfortunate that despite LEDs having tremendous potential to provide good lighting, it's being executed in completely erroneous manner. Headlights were made for EVERYONE'S safety, NOT just the driver behind the wheel.

Wait, headlights that require fans?? I'm sorry but no, just another point of possible failure. I'm sure you could get LED headlights that are less bright, but brighter then stock, and not require fans!

Great video, guys! I wish I could find LEDs for my '15 Ram 1500 like these from F150LEDs. Most LEDs headlamps out on the market are junk. They're marketed for their styling, not output. Did a G search and comes up with pages of the same junk

I also hava a XLT 2020 f350 without fog lights. He is right, Just Candle lights for headlights and when i worked in the mountains for 3 mos, I added Baja Design Fog Lights to my bumper and it made a huge difference especially driving around tight turns in the mountains. I will be adding Projector LED as my main headlights like the Mirimoto M LED. Forget the Bulbs. Projectors is the way to go!

I might be wrong, but hot parts usually fail sooner than cooler temperature parts. Yellow fog lights have always been my pick for cutting through fog and snow. LED white/blue fog lights are popular though.

I used CSP mini led from headlight revolution in my 16 f150. They have a really good beam, almost like factory but much brighter. It would be hard with the f250 but at least with the t150 you can just reach up from the fender well so you don’t have to take anything apart.

I use LEDS and I'll never go back to HID or halogens only one down side high beams generally suck.

Nice work andre and Alex that's why I got the Laramie come standard with led's they are amazing

Are y’all gonna put a ranch hand bumper on there?

May want to look into the Morimoto led headlight replacement. Built to properly focus LED's so it won't blind oncoming traffic. Pricey though.

hmm. that doesn't seem like the best design with a fan, in a few years when there is dirt packed in there your lights will fail and leave you in the dark.

My father in law works for ford and always says "The stupid people who design these know they wont have to work on them" its so true with every brand! Also you can usually reach behind and replace the bulbs by just feeling around!

Times like this I rather keep my 04 Tahoe with two pins that’s on the top of the headlight assembly and change the bulbs within ten minutes tops. I swear that manufacturers make this on purpose for vehicle ownership not to change your own simple maintenance, so mechanics and dealership can charge you $200 dollars and up for something that’s easy to do. Just watch next item will be your wiper blades making one whole piece from the rubber to the connecting spline. And will charge you $300 per blade🤯🤬🤬

I just made an order from these folks based off your video, I really hope they are as advertised!!!

I miss when swapping out bulbs was simple! My 03 Mercury Mountaineer just has quick release system and the whole housing comes out. You can swap out bulbs or a entire housing in less than 5min!

Any recommendations for 9007 led bulbs for my 04 ram 1500?

I can vouch for f150 LEDs, I used there LEDs on my old f150 like 4-5 years ago and they all still work. My sister has the truck now and there still going. Surviving NY winters and salt is hard for any led.

Great job ! Looks much more modern . So why didn’t you replace the turn signals and marker lights ? Lasfit & Headlight Revolution make a turn signal light with built it resistors . Enjoy the truck !!

note to self. order super tremor in a package with factory led lights

Having to take off a fender isn’t exactly what I would call plug and play. This is like one of my sisters old cars. Years ago she had a BMW where one of the headlights needed to be replaced. She was going to take it in to the dealership to get it replaced and I told her why pay all that money because it’s simple to do because I’ve done it before. Well when I went to Autozone to get the bulb and tried to find the housing for the bulb I couldn’t find it. I went in to ask for help and the guy took one look out the window and saw that it was a BMW and said You gotta take that to the dealer because they have to take the whole front end off. It wound up costing my sister almost $200 just to replace a $3 bulb. It’s ridiculous what auto makers make people go through for what should be simple maintenance.

Will the automatic bright dimmer still work with these LEDs???

2022 with second battery absolutely needs to remove grill there is no way to get at the lower driver side light due to a jumbo wire harness. Also, 2022 added a 10 mm nut on each side at the top of the grill. You can not just pull it off. The thread is actually part of the grill. It’s a gray nut that comes off.

Andre, since you didn't show it, did you guys clock the bulbs after installing them? The LED bulbs have an adjustment to allow you to position them correctly. They need to be clocked to where the bulb "blade" is vertical and the diodes point to the left and right.

It just seems that all car manufactures are making it difficult to do any simple maintenance on their vehicles such as replacing front light bulbs. It is the same process to replace the front light bulbs on my 4Runner and Tundra. It is so annoying... Solid work guys...

What happens if a grain of sand gets in the fan and it stops turning? How long will the bulb last?

You guys should take a look at new assemblies from Morimoto XB. Best decision I ever made in my F-150. Lights are top notch and look amazing.

What was the illumination pattern BEFORE? I see is a lot of light in the upper hemisphere. What I want to know is if there is more light where it matters: on the street.

Hope those resistors are placed well because they get waay hotter than you think

Even tho the output might be low on the road, in my Subaru I hate the new fords Bc they are so bright in my eyes head on!

should reach out to headlight revolution and get GTR lighting. get both so we can see which ones are better F150headlights or HR lighting... and here we go

I did this my 2015 Ford Focus. 6 speed put all led light. Before we when trip to Colorado in July. To August

To save bulb life I changed the DRL to just the parking lights using forscan.

I’m gonna go check this out right now, my yellow headlights have become useless

I don’t believe they are going to last if it requires a fan. Dust & dirt will eventually get on the blades and they will burn out in 6 or 7 months

Wow. Put a set of sea light led’s in my 2017 F-150 counting fog lights. 20 minute install. If I had to take the front end apart I would have replaced all the bulbs with led’s. Plus no fans in my heat sinks to fail. 8 clockwise turns on my headlight adjustment so I don’t light up the interior of cars coming the other way. Original light bulbs were so bad they were not safe at night. Especially if it was raining.

Nice!!

I've always hated the LEDs with the fans on them, they were noisy and still burnt out quick, especially after the fan stopped when dirt and salt got sucked up in them. I did find a Philips style that lasted way longer that had no fan.

Love it

It's crazy that you need extra modules for the headlights and fog lights is ridiculous. I can't believe there isn't a company out there that would fix that with such a popular truck. Certainly no issue for other vehicles.

Watching a commercial before a commercial.

I loved my LED retrofit bulbs until my first snow. They did not generate enough heat to prevent snow and ice accumulation on the lenses...

I have a 2022 f250 and you can change the headlight bulbs through the top and from the wheel wells. No need to take all that apart

The name of the game is experienced in patients hey guys I have been in the aftermarket accessory world for 30 years cars boats RVs side-by-sides motorcycles you name it I've done it all from Mild to Wild best of luck Andre I love the video series that you always do don't tell anybody but you're my favorite lol.

To those complaining about cost cutting. Ford sells roughly 1 million f series trucks a year. If these headlights were standard and cost Ford an extra $50 per truck to install and half the trucks they sold were base trucks that needed the upgraded headlights that's $25,000,000 per year in extra costs. Not everything can be standard equipment or they will not stay competitive in their pricing.

Blind the on-coming drivers. It's ok, you can see. Inconsiderate to others.

Great mod Andre.

I said no as soon as I heard they have fans. I don't need a fan crapping out and melting my headlights. Just wait for the totalled f150s to hit the scrap yards and grab some OEM stuff

I’m glad you guys took my advice on reaching out to f150leds.com. They have great kits. And the bad design for the headlights is all Ford, they have been making a consecrated to swap out lightbulb over 10 years

Include the helping hand (casey?) in more videos, he always does well as far as talking/demonstrating on camera!

I thought it was bad to swap a halogen bulb for an led bulb as the reflectors and lens are not correctly tuned. I thought the only proper way was to use a complete light kit with lens reflectors etc.

After having these bulbs for a while, are you still happy or is there a better option Thanks, Bob

Can you please show the beam pattern at night on a wall with low and high beam? I have a 2020 and have tried 4 different set of LEDs and they all have a spotty beam and not super impressed.

Nothin against F150LEDs.com, but these particular "bulbs"(diodes) are not the best option. They're not BAD by any means, but a pair of GTR Lighting CSP Minis in this size is equally bright if not more so, and does NOT require all that relay shit and cooling fans that these seem to require AND they're only about $140 for a pair. If not the CSPs, even just the regular GTR Lighting "bulbs". Cheaper and brighter too. Headlightrevolution.com has a plethora of videos here on KZfaq comparing various Amazon and eBay diodes in the same housing and they measure actual lux and beam pattern too I'd DEFINITELY recommend checking out their videos, especially if you have a late model F-Series.

Did you miss a screw holding the panel on? I have only seen one video where a guy removed it. Similar to the bottom "hidden" screw but a nut on the back of the top. When you removed the panel it looks like there is a bolt there.

It funny to see Tommy and Andre to have a conversation about headlights.

Shame on Ford for providing such pathetic and unsafe base headlights.

The 02-14 Volvo XC90 has quick release headlight housings. You just pull up two rods and that frees the whole housing.

we will see how long they last before they have issues. I had similar lights from the same manufacturer on my 2015 F150. They lasted a year. I switched to PUTCO lights. havent had an issue since (knock on wood)

What happens when you get dirt/mud/muddy water into the fan on that LED?