Just installed today, very happy with it! High quality product! Make more stuff for the Mavericks? An aluminum under car shield would be an awesome replacement for the OEM fabric shield.
@sjones617710 ай бұрын
After watching your video I ordered this catch can and have been impressed. The quality of both the can and hoses were top notch. Installation was relatively easy, took about 20 minutes to do. Looking forward to seeing what the can captures in the next couple of months.
@h20mxracer2227 ай бұрын
I didn't know these were needed until I started doing some research. Wonder why Ford wouldn't do this from the factory. This is my very first brand new vehicle. I need it to last many years. I'll definitely be installing this system. Thanks for the video!
@dethpig4205 ай бұрын
I think a lot of it is due to cost cutting and less of a need for maintenance. We all know most Americans barely maintain their stuff. An oil catch can does run the risk of freezing in the winter months as well. Could cause some problems.
@ronhanish7 күн бұрын
For the orange clips an easier way just use the corner of a flat putty knife, probably need to for both of them at the same time, or a couple thin pieces of sheet metal
@charlesgard1119 ай бұрын
Was very easy to install after I watch the video and saw where he placed his hand to find it
@dethpig4205 ай бұрын
Installed my UPR oil catch can this evening, march 27th 2024 with 3,347 miles on the Odometer. Super oily in the dirty side as you pointed out and my clean side smells of fuel mostly. A few things to note as an aid to others. First for an old dude, you are pretty dang flexible! Haha! I’m 36 coming up and man that dirty side was a PAIN to get to. I felt like that John Edward Jones dude for a minute there. However you failed to note whether or not which catch can is the dirty or clean side. I had to simply look and see, okay skinny fittings are dirty and fat are clean, but some may be confused the first get go. I know, minor. Next, I do not recommend a pick on the orange fittings, on the clean side. I simply recommend going for the intake portion first. getting that little wire above the line out of the way by disconnecting it. Then, just straight towards your body, pull that thing from the intake part FIRST, it will snap free with relative ease if you’re strong enough. Then, simply tug straight UP on the valve cover portion and same thing, snap! Off comes that lame hose! Believe me I’m a total Neanderthal and i cut my hands a little with my lick until I saw another gentlemens KZfaq video, the Cuban Redneck. I stole his idea! Thanks buddy! I mean really that’s it. It is a pretty straight forward install. Best of luck to those out there modding their mavericks! Thanks UPR for my catch cans! Cheers!!
@Bohefus5 ай бұрын
Nice informative install video (factory style connectors with a very satisfying click)
@rickslick755 ай бұрын
Love your catch cans, have them on all my Fords. I have a question, can I get more info on the wheel and tire combo? I love the look and would live that setup on my Maverick.
@unorthodoxridez10 ай бұрын
What a beautiful product!!
@ronhanish7 күн бұрын
So what does that kit do for the car?
@ronhanish7 күн бұрын
Make an H2O hydrogen gas kit..easy fuel savings.boosts mileage by 1/3 rd average
@suunto616 ай бұрын
Looks to be exactly the same procedure as many other 2.0L eco boosts.
@dieselford91845 ай бұрын
Can you guys make a catch can for the 2023+ ford Escape with the 2.0 ecoboost? Please!
@stevebussius78875 ай бұрын
Sure! Drop one off to UPR and we'll get one made.
@dannymcgirr6 ай бұрын
This looks like it should still work if we have hood struts installed, which access that same mounting point, but look to be on the side - and this bolts on underneath. Anyone tried both together and can confirm if this works or not with a strut kit?
@ronhanish7 күн бұрын
What's it for??
@user-pp2rc7nj9m8 ай бұрын
Very good video, thank you sir 🙏
@brandoncarpenter65552 ай бұрын
Would there be any draw backs to blocking off the inlet to the manifold and just routing from the PCV valve to a vented can?
@brandoncarpenter65552 ай бұрын
also just venting the VC and blocking off the inlet on the intake....?
@uprproducts2 ай бұрын
That is a big no no. Blocking off the inlet will effectively eliminate the crankcase vacuum and scavenging effect in the PCV system and cause blow-by and poor economy.
@uprproducts2 ай бұрын
@@brandoncarpenter6555@brandoncarpenter6555 If you vent the valve cover, you eliminate the vacuum from the PCV system and reduce ring seal, mpg, and longevity. New technology thrives on PCV vacuum for better ring seal, pulling fresh air into the crankcase, and having more of a suction effect at all times, which is very beneficial for any engine. The key is to have the best UPR catch can system for your vehicle with high-flow check valves and a UPR one-way valve cover breather to be sure you are capturing oil before it reaches the cylinder, and you're all set.
@bilstein24105 ай бұрын
At 7:29 you make a comment that the air has to travel both ways through that tube. Is the catch that you're going to install on the clean side. Still going to allow The air to travel back and forth as it's needed?
@uprproducts5 ай бұрын
Yes, the air still flows in both directions. However, you cannot install a check valve on the clean side, as it has to remain bidirectional. Only the dirty side gets a check valve.
@bilstein24105 ай бұрын
@@uprproducts ok perfect..
@edros2218 ай бұрын
Asume should be the same for Bronco Sport Badlands, right?
@stevebussius78877 ай бұрын
As long as it is a 2.0L , yes, it should be.
@peterwilson169911 ай бұрын
Thanks bro for the video
@marshellli8107 Жыл бұрын
Is it recommended to install both, and can you provide the link from the website? Thank you
@stevebussius7887 Жыл бұрын
It is recommended to install both the PCV and Clean Side catch cans, however it will be available as a PCV side only with an option to add the Clean side for those folks that do not want both. It will be available on the website by August 4th
@rileydavis144711 ай бұрын
How can I purchase this kit? Does it have any affect on factory warranty?
@s.b.171311 ай бұрын
If you install it correctly, no.
@rileydavis144711 ай бұрын
@@s.b.1713I want one. Is there a link? I’m sure there is. Thank you!
@medic283411 ай бұрын
Do you make a catch can kit for the 2023 Ford Explorer with the 2.3 engine?
@stevebussius788711 ай бұрын
Not at this time.
@danthompson14674 ай бұрын
I have fuel in my oil at 5% 2300 miles on the oil 11685 miles on the truck what’s the fix ?
@uprproducts4 ай бұрын
It's normal to get fuel in your oil in the catch can/oil separator. Most new engines get a lot of blowby and fuel through them, which is why it's recycled to the PCV system to be burned in the combustion chambers. Sometimes, after normal breaking, that will decrease a bit, but that is nothing to worry about.
@ericmccusker56527 ай бұрын
Can you access the lines easier from under the truck?
@stevebussius78877 ай бұрын
No, It is not easy to reach it from underneath
@loganhollingsworth312610 ай бұрын
no check valve needed?
@uprproducts7 ай бұрын
If you are running both the clean and dirty side catch cans you can add a (5044-02) UPR Pro-Series Check Valve on the UPR Dirty Side Catch Can (5049-288).
@dtron5000boi7 ай бұрын
@@uprproducts can you please clarify: the check valve would install between the can and towards the intake manifold? Also, are then different hoses supplied which accommodate the check valve, with clamps?
@stevebussius78877 ай бұрын
@@dtron5000boi If you opt to add the check valve when ordering, the check valve will be installed in the vacuum hose ( the one connecting to the intake manifold ) when the kit is built. If you want to order one after the sale, you can cut the hose and install the check valve easily yourself.
@Sfk8872 ай бұрын
What is a catch can?
@stevebussius78872 ай бұрын
🤦♂
@stevebussius78872 ай бұрын
When your PCV system HAWK TUAHs into your intake tract, the catch can keeps the oil out.
@user-rt5ic7ob5g4 ай бұрын
엔진.룸이 왜 이리 복잡하냐?
@uprproducts4 ай бұрын
It takes a very tight and compact engine room to fit an EcoBoost motor in a great chassis. It's worth the extra work to make sure you have the best oil separator to guarantee little to no oil ingestion for the best overall performance and mpg.
@s.b.17134 ай бұрын
So here in Canada I take my Mav into the dealer from time to time for warranty etc. The service clerk told me last visit (oil change as I was super busy), "oh our tech advised you have a catch can and there was a bit of fuel in the oil and it's due to the catch can installation you did", I nearly shat my pants as in how absolutely daft was this person and the technician who should know better. So in the USA you all have a court ruling in place and I was doing a search but coming up empty handed, anyone know what that was in the event my 2.0 shats the bed and I have to fight Ford on any warranty issues.