Using an On Board Effects Loop (OBEL) Equipped Guitar with The HubBub OBEL Junction Box

No video

Using an On Board Effects Loop (OBEL) Equipped Guitar with The HubBub OBEL Junction Box

Рет қаралды 22,778

Күн бұрын

This video explains how to connect an OBEL equipped guitar to the HubBub OBEL Junction Box using a Dual TRS/TS Cable.
The HubBub and Dual TRS/TS Cable in this video is made by Godfrey Daniels Guitar Works
hubbubpedal.com/
The DeadBolt guitar is by PHRED instruments
shop.phredinst...
The following effects pedals are used in this video
Mu-Tron MicroTron III
www.mu-tron.co...
Mu-FX Phasor 2x (Discontinued) Link to Mu-Tron Bi-Phase
www.mu-tron.co...
TC Elecronics PolyTune 2
www.tcelectron...

Пікірлер: 18

@danpejril 6 жыл бұрын

Great video. This is a very clear demonstration of how the OBEL works and the benefits of having one.

@PHREDinstruments 6 жыл бұрын

Thanks, Dan!

@TheScreamingFrog916 4 жыл бұрын

Is there also a send volume to the effects, on the guitar, so you can adjust how hard the signal hits the effects, as well as the post effects send, from the guitar? That would seem to provide the most flexibility. Or maybe a stacked volume, that turns up the effects send, while turning down the amp send. So the overall volume does not change, as you hit the effects harder? That would be awesome.

@PHREDinstruments 4 жыл бұрын

There isn't a pre-effects loop volume control, but there is a post-effects loop volume control. It's very possible to re-purpose one of the tone pots as a pre-effects loop volume control, or to use a concentric volume knob with a stacked pot to achieve pre and post effect volume control.

@riffwizardsupreme 5 жыл бұрын

Could you alternatively just use a stereo Y cable instead of the junction box?

@PHREDinstruments 5 жыл бұрын

Fedowicz yes.

@sirhamalot8651 6 жыл бұрын

So...this allows for a chain of effects to be turned on/off from a switch on the guitar rather than hitting a bunch of stomp boxes? Is that the point?

@PHREDinstruments 6 жыл бұрын

That's a big part of it. The other part is that when you are playing without effects, the guitar signal goes directly to your amp, bypassing effects pedals that may suck tone from the signal. You could also place some pedals in your effects loop, and some pedals in between your guitars an amp, like a standard setup, a wah pedal for example, or a compressor pedal that you always want on.

@tuckertammaro2985 4 жыл бұрын

Good video, just confused why dudes got an 8 point bolt on that guitar

@Acolis 4 жыл бұрын

its a half assed 13 point dead bolt

@williambourdeau5925 4 жыл бұрын

13 points would be copyright infringement.

@ToddWCorey1 4 жыл бұрын

Your G string is improperly seated in its saddle.

@rob-e-bananers 5 жыл бұрын

Curious why you’d use the Hub Bub with a guitar not using OBEL?

@PHREDinstruments 5 жыл бұрын

If you have both OBEL and non-OBEL equipped guitars the HubBub makes it easier to switch between playing them with your effects pedals.

@goodwi11 6 жыл бұрын

In some instances, do the tip and ring need to be swapped in order for it to work properly?

@PHREDinstruments 6 жыл бұрын

goodwi11 the HubBub is wired to work with the Tip being Send and Ring being the Return on the TRS OBEL output jack on the guitar. If things are not working properly with the OBEL engaged, then yes, the wires going to the tip and ring need to be swapped.