Vacuum Table Setup for CNC Router (Older Model)

Vacuum Table Setup for CNC Router (Older Model) | Laguna Tools

Рет қаралды 273,621

Күн бұрын

Explore Laguna CNC machines: bit.ly/2S3ruK4
Subscribe to our email list for sales and promotions: bit.ly/3wFb9K6
How to set up the vacuum table on a CNC router.
►Contact Laguna Tools for more info: bit.ly/35UqV6M
►Subscribe to our channel: bit.ly/2r5Czgc
►Instagram: bit.ly/2mph6wt
►Facebook: bit.ly/2qiHpXi

Пікірлер: 36

@zhoulira8463 9 жыл бұрын

Nice video! BTW I like the control system.never see it before.

@sc0rpi0n0 10 жыл бұрын

Thank you for this helpful instructional video.

@andrewrother3311 4 жыл бұрын

Thank you for posting this!!

@AliKhan-iz5xm 8 жыл бұрын

awesome video thank u

@mikedcaffey 8 жыл бұрын

these videos are great, thanks for making them.

@LagunaTools 11 жыл бұрын

The video is about setting up the Vacuum for a Laguna CNC, therefore preparing the table to control the vacuum suction to hold wood panels down onto the table.

@jamilhasan 5 жыл бұрын

Thanks

@DiscoveryBOOM 11 жыл бұрын

good . nice work

@robnai3372 10 жыл бұрын

Thanks for counting the valves after you told us there were six. Nearly didn't believe you. Nah just kidding

@nautilus1999 6 жыл бұрын

Do you recommend LDF MDF or HDF to be sacrificial board that sits on a table . Also should a rubber gasket sit slightly above black table surface .

@LagunaTools 6 жыл бұрын

Lets discuss, call us at 800.234.1976 for a quicker response. Thank you for your interest.

@LagunaTools 10 жыл бұрын

Пожалуйста, дайте нам знать, что вы подразумеваете под сотрудничать?

@MSCNCArtshop 11 жыл бұрын

Hi - what is the rating(kw) of your vacuum pump - if I may ask :)

@user-ry4ie9de5r 8 жыл бұрын

Hi, what pipe diameter and pump do you recommend using? I am making a table 1220*2440mm, with 6*6mm grooves, 25mm between grooves. Thank you

@softlock6504 8 жыл бұрын

pretty well any shop vacuum cleaner will work

@1010bobi 8 жыл бұрын

Great job! What kind of material is the vacuum table made of?

@scarlettgao5985 8 жыл бұрын

PVC

@cnccarving 7 жыл бұрын

vulcanized rubber

@bobcampbell4263 7 жыл бұрын

how many cubic feet per minute are required to run a vacuum table this size???Thanks

@LagunaTools 7 жыл бұрын

Please call us 800.234.1976

@MrFratma 6 жыл бұрын

Hi, when i surface the second side of my spoilboard i lose vacuum for every pass as the board starts to bleed thru ending up with the gasket pushing the board from the vacuum table and giving me a slight leaning surface when done, do you have any advice about how i can avoid this?

@LagunaTools 6 жыл бұрын

Our CNC techs can be of a great assistance to help you, please call 800.332.4094 - Thank you for reaching out to us.

@Dover1044 7 жыл бұрын

Where can you buy the Gasket?

@LagunaTools 7 жыл бұрын

Please call us upon discussing where to buy the gasket pieces for your CNC router at 800.234.1976 - Thanks for reaching out to us.

@ericparent728 7 жыл бұрын

Would have been nice if he actually told and showed you where to enter how much you want to take off. Do you do this in a program or do you adjust the Z height?

@LagunaTools 7 жыл бұрын

Our CNC technicians can assist you, please call us at 800-332-4094

@johncrosetti2568 8 жыл бұрын

@ Despicably Irascible Rapscallion... It's not just to hold down spoilboard. You have to skim off both heat treated surfaces of the MDF (as video shows) then vacuum table pulls the suction THROUGH the MDF. Seems like it would't work but it does. MDF is dense yet very porous once skimmed.

@timmillervideo 7 жыл бұрын

John Crosetti is that right? That's what I was hoping he was getting at but was disappointed when the video ended before he showed the whole purpose of what he was doing.

@SamHocking 6 жыл бұрын

If the MDF is made porous all over to a vacuum by skimming the surface each side, how is the vacuum held to a smaller piece being cut above? I can't see how zoning with a smaller gasket makes any difference if the vacuum can be pulled through the MDF from outside the gasket? Is it just a very powerful vacuum required?

@LagunaTools 11 жыл бұрын

10HP