How to check and adjust the valves on a 2014 Vespa Sprint 150 3v. Also applies to 2015 Vespa Primavera 150 3V.
Пікірлер: 51
@VoyTe7 ай бұрын
My favorite scooter mechanic on KZfaq. Thank you for your videos. 👍
@forrysc3 жыл бұрын
Unbolting the rear shock makes it possible to get the valve cover out. Otherwise, I couldn’t get it out. My biggest problems with the valve check was being able to refit the valve cover and keeping the o-ring/seal in place. It fell out every time. I used a small amount of tacky grease to hold the o-ring in place. Find feeler gauges like the ones robot is using. The standard feeler gauges are hard to use. I did the two intakes from the top reaching down as opposed to using the access panel. Two of my 3 valves were tight.
@brendamake17609 жыл бұрын
Thanks. I haven't seen much about these new motors. @bigissue, these engines do not have hydraulic self-adjusting valvetrains. Valves--especially the exhaust valves get longer during use, reducing their clearance and then they won't seal well. If the valves don't seal against the seat because the valve-train is holding it open, the valve and seat will get hotter than they need to, which further accelerates their stretching and seat wear. During that time, the engine just won't have as much power as it should because the engine can't keep compression after the sparkplug ignites the fuel-air mixture. I've heard from a Vespa mechanic of an engine that would not start from valve-clearance issues alone, likely because modern Vespas, already have an engine-decompression system to reduce the load on the starter, and having leaking valves might lower it until the point where it wouldn't start at all.
@2FatBelgiumBastards5 жыл бұрын
Great video!! I was wondering if it is the same way of adjusting the valves for a 4 valve engine? (I have a 4 valve SOHC Piaggio engine for my Aprilia Atlantic 2007)
@jobeppe7 жыл бұрын
This engine is also on the 2012-2014 Vespa Lx 125/150 3 Valvole i.e. here in Europe. I have one in Portovenere green :)
@calasmallorca11837 жыл бұрын
got a problem with a primavera 50 (carburation and 4stroke)... it starts, revs up itself and inmediatly after 10 secs stop. Then if you let it rest 2 min it will start again with no problem and stop again......any thoughts?? carburetor , valve adjustment, air leak.......???
@razvanbutiac76842 жыл бұрын
Hi Robot, how you adjust the valves when there is a king of ball joint on the end (have a ET4 with this arrangements)
@user-bm6lx6px3n5 жыл бұрын
Good day. Hello to you from faraway Kazakhstan. If it is not difficult to tell me please. I have a Piaggio ZIP engine 125 carburetor. I want to install it on the Vespa LH 50 2t scooter. Which sdi switch is suitable for starting this engine ????. In addition to the ACI503. I will not have an immobolizer. Thanks for answering.
@allday343310 ай бұрын
Where can i get some cheap new intake valves for 2020 liberty 150 ?
@madogblue4 ай бұрын
I womder if this is the same for the IGet engines?
@takhuong74324 жыл бұрын
Great video ! Tks you
@gamergeorgex11 ай бұрын
I have a 125cc iget 2021 3v engine. Is the method the same for finding TDC?
@EstebanRojasCastillo2 жыл бұрын
How can I get a service manual for VXL150 3V?
@themullystacheshow361010 ай бұрын
Quick question, the owners manual says both I take and exhaust should be 0.8
@buboy0714 жыл бұрын
why is it according to the manual it's both .08 mm for both intake and exhaust? and robot uses .004 for the intake and .006 for the exhaust. I'm a little confuse.
@hoedemakerbart3 жыл бұрын
0.10 for Both is fine
@pawciu752 жыл бұрын
So why not 0.08mm bor both sides? I am confused also
@madisonscott4677 Жыл бұрын
He uses inch not millimiter gauge
@Kayemtee3 жыл бұрын
Hopefully, I can ask a question here? I take delivery next week of a new Primavera. As I live 200 miles from the dealer (and 150 miles from the nearest Vespa dealer). I can change the engine oil and filter myself as well as the gear oil, but adjusting the valves is well beyond my skill set. As the valves on the engine shown here were slightly tight with just a few miles, my questions are these? Are they tight from the factory or do they tighten up with initial use? Is there any point in having the dealer check the clearances on the brand new engine before they ship it to me? If not, will I need to transport my new scooter to an authorized dealer to have them checked at 625 miles? Thanks much.
@jamesconner34372 жыл бұрын
My experience : A reputable dealer will not let a scooter leave with bad valves...they will only get worse by 600 miles. If you are careful to not overheat the engine for first 300-500 miles, valves should be good till 1200, when you should probably return to that dealer for a checkup. Again. a reputable dealer will understand your geographical problem in being "overdue", because Vespas don't have valve issues as a common thing, anyway. Valves just slightly out are not a fatal or totally uncommon problem even for well manufactured scooter motors. For sports and race cars, maybe.
@DavidsOutdoors5 жыл бұрын
I just paid 300 dollars for this service! Lol I should have watched this video before hand and done it myself! Next time!!!
@anjarnursandi86954 жыл бұрын
In 0.14 ex0.16?
@fakrulfauzi91592 жыл бұрын
hello mr robot,i just take back my primavera 3v from a workshop that lies to me..n when i check the head cover i realize i lost 1 part bcoz i see in ur video u have it there..what u call it crank lock or what..im sorry bcoz im new ...is it ok i didnt hve it there?
@erikprastomo85725 жыл бұрын
Om kuku nya item bgt ? Sama jambang ga pernah di cukur ?
@hakkoy588 жыл бұрын
hello I need 2005 piaggio fly 150 scooter carburetor setup and hose connection picture information .... Thanks
@spivzespivatron6596 жыл бұрын
Soner Yaman they wont reply they never do
@pasir.70667 жыл бұрын
good job
@anibalguzman5 жыл бұрын
Also applies to 2013 Vespa LX 150 3V.
@itsh20123 жыл бұрын
how to change Sora tongue vespa?
@frankpa32636 жыл бұрын
loss power after valve adjustment, setting was .10mm and .15mm @top dead center, still no power, before adjustment - power is very good? what makes a problem? pls help. thank you
@wangodex846 жыл бұрын
Frank Pa check the valve... If there any crack or you haven't polishing it... Also check if your valve was bended or not... It's really important thing for compression
@Robert-yk1bw6 жыл бұрын
It is 0,10mm intake and 0,15 mm exhaust outtake as far as I know
@rbhgaming10245 жыл бұрын
adjustment in 0.8 and out 0.8 best setting for 3v engine
@madisonscott4677 Жыл бұрын
@@rbhgaming1024 yes as described in the manual
@jamminjesus7 жыл бұрын
Are the valve clearances the same spec on the older engine (2009 Fly 150)? Thanks! All of your videos are great BTW. You guys are awesome!
@patrickgoddard64494 жыл бұрын
My first thought. Robot legend!
@csrr37243 жыл бұрын
Hi iam from india ,pl upload vespa Geared 150 4t engine complete overhaul
@sumiellyana62213 жыл бұрын
do you have a connecting rod for the vespa sprint1503vie
@VespaMotorsport3 жыл бұрын
Give us a call. 619-280-1718
@sumiellyana62213 жыл бұрын
sorry we can't speak english this live just have to open the dictionary first and we have trouble finding that item and we are far away in indonesia
@sumiellyana62213 жыл бұрын
#vespa Motorsport maybe you can call using the line
@fdp6919 Жыл бұрын
Mi moto tiene ese motor pero a perdido fuerza puede ser un ajuste de válvulas ya tiene 12345klm y nunca se a echo
@atanasiusk8 жыл бұрын
the valve adjusment? intake 0,04 exhaust 0,06???
@richoberdorfer60317 жыл бұрын
Atanasius Kurnia Correct valve clearance for these bikes is .08mm for both intake and exhaust, according to my 2015 Sprint owners manual. I can't tell if Robot made a mistake, or if his shop prefers these looser clearances based on their experience.
@richoberdorfer60317 жыл бұрын
Atanasius Kurnia .08mm is .003 of an inch. Robot is using non-metric tools, .004 and .006 of an inch.
@sannimanjhimanjhi44755 жыл бұрын
full enjan ripering dikhao
@TheScottbm5 жыл бұрын
Is Robot drunk?
@patrickgoddard64494 жыл бұрын
My first thought. Legend
@khalandar80944 жыл бұрын
Hi
@yuli.dwitriantidwitrianti68013 жыл бұрын
I probably bored up to 200cc
@bigissue91799 жыл бұрын
hey people valve adjusment on first service are vespa crazy get a 300 gts had it since 2009 change the oils new exhaust tyres engie mounts and tighting steering bearings all cheap to do and still going after 40000kms forget this engine