Liked your format, step by step before and after each removal. Easy to follow and straight forward. Thanks man
@ThePullUpKing Жыл бұрын
Not a problem man! Thanks alot and thanks for watching!
@MarkSWest Жыл бұрын
Awesome video - I don't normally work on Hondas, this helped tremendously - thanks - GREAT JOB!
@ThePullUpKing Жыл бұрын
Nice! Thank u and I appreciate you watching!
@bobflyer43469 ай бұрын
Just received a quote for my Honda Accord v6..Northwest Florida $529. The Kit from Fel Pro Rock Auto is 20.79 with all items needed for repair. Thanks for the Video
@ThePullUpKing9 ай бұрын
Yessirr, thanks for watching!
@dvd6722 Жыл бұрын
Shorter and more concise than videos which are twice as long. Good tips and methods to watch out for. Nice explanations and format / editing. I have a 2010 V6 Accord with 180K on it, and I'm preparing to do it this spring / summer. I like your method of tapping out the rings from the top instead of prying from the bottom, use of channel locks for removal and install of those bolt ring thingies and your use of sealant at the corners of the gaskets.
@ThePullUpKing Жыл бұрын
Yessirr! Thanks man I appreciate the recognition.😎 I tried to make sure I covered everything. I hope it helps out. Let us know how the repair goes.
@dvd67227 ай бұрын
@@ThePullUpKing I still haven't done it, but I'm gonna. I just turned 200k and I plan on doing it soon Q1: Is it easy to find the torque values online? Q2: The 8th gen V6 s is prone to fouling plugs as a result of the VCM. Do you have any knowledge of the effectiveness of the aftermarket VCM limiter which keeps all 6 cylinders running continuously? Q3: Do you have any tips that would help make this engine last another 100k plus? Thanks, Dave in Ohio
@Jrhortian9 күн бұрын
How did your install go last year? I just had a plug fail and oil was on 4 of the 6.
@dvd67229 күн бұрын
@@Jrhortian I didn't do it yet, but I'm still putting 700+ miles on every week. Correct me if I'm wrong but I don't believe the valve cover gaskets replacement will affect the oil on the plugs. The fouling of the plugs is caused by the VCM (Variable Cylinder Management) which alternates between shutting down 2 alternating pairs of cylinders while at moderate RPMs (not climbing, not accelerating.) As a result, oil collects in the 2 non-firing cylinders and causes 4 of the plugs to get gunked up. There is an electronic VCM tuner module which will disable this feature. I read that it doesn't make much difference in MPGs. Haven't installed it yet. I replaced my plugs quite a while ago with the NGK laser iridium. I suspect that they were developed for this type of problem, but I can't know for sure. They seem to be less prone to fouling out. In the meantime, I just make sure I drive it somewhat aggressively once it has reached full operating temperature to keep oil from building up in the VCM cylinders while keeping the full synthetic oil level topped off. The engine light doesn't bother me. I had 4 out of 6 gunked up as well back when I did it. I really don't know, I might be wrong. Will the valve cover gaskets and seals replacement prevent oil from entering the ignition chambers? (I'm not a pro mechanic)
@ThePullUpKing9 күн бұрын
Replacing the tube seals is what stops the oil on the plugs.
@adriasihudson1578 ай бұрын
Good explanations, easy to understand, thank you. Looking forward for more videos.
@ThePullUpKing8 ай бұрын
Thanks man! I appreciate you watching
@franklynpertuz76693 ай бұрын
Yes it was a lot easier watching this video cuz I seen some videos installing this I have an Acura I have to do is a 2001 doing the same thing thank you appreciate it and sharing this
@ThePullUpKing3 ай бұрын
Thanks alot and thanks for watching!
@roynguyen63954 ай бұрын
Hey man. Nice video. But I have questions about the gasket. Why did you just apply only in the corners? Is it better put all the way around it? And do you put the sealant rtv on the cover first or after you put the gasket? Just curious sir. Thank you for this video!
@ThePullUpKing4 ай бұрын
Thanks! Those are the areas where oil will leak if sealant isn't applied. The gasket will seal the other areas. If the gasket doesn't stay in place, apply the sealant lightly, to hold the gasket to the cover.
@jonathannorton3094 Жыл бұрын
U need to be the cometary for every mechanic video out there like seriously Ty and good job bro bro!
@ThePullUpKing Жыл бұрын
Lol Thanks man, I appreciate it!✊🏾
@brianrohm67576 ай бұрын
Mine is starting to leak oil onto my new altenator time to get mine done good video
@ThePullUpKing6 ай бұрын
Yessirr! I appreciate it. Thanks for watching!
@jorgeirizarry597110 ай бұрын
My car is even the same color 😂. This was very specific, even the car color.
@ThePullUpKing10 ай бұрын
🤣
@hermanwilliams536 Жыл бұрын
Great detailed information
@ThePullUpKing Жыл бұрын
Thanks alot and thanks for watching!
@martinkoche4375 Жыл бұрын
Great video thanks for sharing
@ThePullUpKing Жыл бұрын
No problem. Thafor watching!
@calebinorio100 Жыл бұрын
If this doesn't solve my issue... I hope it does. Thanks for the in-depth explanation Sir
@ThePullUpKing Жыл бұрын
Absolutely! Thanks for watching!
@calebinorio100 Жыл бұрын
Question, Did you also replace the alternator or just clean it off? The oil has been drippin on my alternator
@calebinorio100 Жыл бұрын
Also did you need a new air intake manifold gasket ? I’m attempting this weekend
@ThePullUpKing Жыл бұрын
@@calebinorio100 The videos shows valve cover gaskets being replaced. Didn't touch the battery. Intake manifold gasket reusable.
@Peace-Of-Mind- Жыл бұрын
@@calebinorio100 what did you end up doing? My valve cover gaskets leaked oil onto my alternator
@Moriconilo Жыл бұрын
thank you!
@ThePullUpKing Жыл бұрын
No problem! Thanks for watching
@medalla67 Жыл бұрын
Questions: Is there a specification on thighting the bolts on the cove valve?
Hey dude, great video! What is the tube of gasket seal you used?
@ThePullUpKing4 ай бұрын
Thanks man. I appreciate you watching! Gasket sealant www.autozone.com/sealants-glues-adhesives-and-tape/sealant/p/permatex-ultra-black-rtv-silicone-maximum-oil-resistance-gasket-maker-0-5-oz/415412_0_0?vehicleId=4767601
@NATURALGAMING2 ай бұрын
🔥
@ThePullUpKing2 ай бұрын
💯
@Uncle_Matt_ Жыл бұрын
Nice work. Are new gaskets needed for the manifold? Thanks
@ThePullUpKing Жыл бұрын
Thanks alot for watching! New gaskets are not needed. They are reusable.
@jmrd72255 ай бұрын
@@ThePullUpKingthanks
@Fucktony714 Жыл бұрын
Hey man maybe you can help me with my issue, i was removing my pcv valve and it broke. Everything came off except the very end of it. You think if I remove the front valve head I can push it out from the inside?
@ThePullUpKing Жыл бұрын
I would just break the pcv valve into little pieces with a flat head and fish the pieces out with a needle nose. Or you could take off the cover.
@johnathansotomayor23997 ай бұрын
Thanks!
@ThePullUpKing7 ай бұрын
I appreciate that $5 bro🫡
@sillykidd5720 Жыл бұрын
I’ve been trying to remove the cover for about an hour and it won’t budge. I got the left side up but the right side by where all the coolant lines are at, it’s just not budging for me. Any suggestions?
@ThePullUpKing Жыл бұрын
Make sure all the bolts & nuts are undone.
@JorgeChavez-xm2ew Жыл бұрын
It's there a torque value for the valve covers and manifold? Actually for everything? Just wondering. Great video.
@ThePullUpKing Жыл бұрын
Yes sir, but I don't use them all the time. I can send them to you. Thanks alot and Thanks for watching!
@@ThePullUpKing thank you for the torque spec ive been wondering the same thing great video thanks again my man
@ThePullUpKingАй бұрын
@@ivonnejoshua4102 Yessir, thanks for watching!💯
@MrSamPhoenix Жыл бұрын
Good job, but when doing this job I always clean the entire area first. This way no dirt of debris falls in
@ThePullUpKing Жыл бұрын
That's a good habit. Thanks for watching.
@alexace3127 ай бұрын
How did you clean those areas without taking anything off did you just spray it with the brake cleaner ?
@ThePullUpKing7 ай бұрын
Which areas are you referring to?
@alexace3127 ай бұрын
The area by the alternator
@ThePullUpKing7 ай бұрын
Yeah, brake cleaner
@alexace3127 ай бұрын
How did you get the back valve cover back in I can’t get it in without the gasket falling off
@ThePullUpKing7 ай бұрын
Use sealant.
@silversurfer702 Жыл бұрын
Ballpark. How much does that service cost on a 2007 Accord V6?
@ThePullUpKing Жыл бұрын
$500
@rpruneau68 Жыл бұрын
Should be about 2.5 hour labor time plus parts so best to do the calculation based on YOUR local area shop labor rates and current cost of parts.
@Siris359 ай бұрын
How do you know if it wasn't the solenoid spool?
@ThePullUpKing9 ай бұрын
I diagnosed it myself. Oil leaking from the valve cover gaskets. The purpose of the video is to show how I replaced them. Thanks for watching.
@Apulux Жыл бұрын
Yo bro the the front bracket that you took off how important is it? My car doesn’t have one for some reason
@ThePullUpKing Жыл бұрын
Time stamp it so I can see what you talking bout.
@Apulux Жыл бұрын
@@ThePullUpKing at 4:18
@Apulux Жыл бұрын
@@ThePullUpKing also im trying to replace my rear vvt solonoid PN(15820-R70-A05), do you have any videos on that but this same exact car? ive already changed the sensors many times code still comes up, so now i have to replace whole piece. or do you have any tips on replaceing it, i cant seem to find a video on youtube.
@ThePullUpKing Жыл бұрын
@@Apulux Not important
@ThePullUpKing Жыл бұрын
@Apulux No video on that repair. Gotta be something online about it.
@OmarGonzalis3 ай бұрын
Right is the front one?
@ThePullUpKing2 ай бұрын
Im not sure. It's either front or rear.
@jeffreyhorne77753 ай бұрын
How far are you and what is the charge
@ThePullUpKing3 ай бұрын
Service Atlanta, Ga & surrounding cities
@slidin1224 ай бұрын
What was the total job time ?
@ThePullUpKing4 ай бұрын
Depends on how fast you work. Took me a good 3-4hrs.
@AmpereNA3 ай бұрын
no hate but I did this and it leaked after 2000 miles really really bad. the gasket sealer you used is from harbor freight, I used that same exact kind also, and it is not what you want. You want Hondabond OEM sealer, OR permatex ultra-grey/copper. I had to redo this job on my car bc of this wrong stuff.
@ThePullUpKing3 ай бұрын
Nah bruh you just didn't seal it properly. Lol My job ain't leak, so I know that's just ya opinion. I been doing this since 11th grade man. No hate. Check ya work.
@AmpereNA3 ай бұрын
@@ThePullUpKing yea you mentally still in the 5th grade, now im hatin. Do your homework use Hondbond.
@ThePullUpKing3 ай бұрын
💀🤣🤣 But u on my channel, talking bout do ya homework.🤣 I said what tf I said. You didnt do the job right if it's still leaking. Can't get mad at me for telling you the truth niccah.🤡 You did the fuxkin joh wrong dumbss boy.😆😂
@AmpereNA3 ай бұрын
@@ThePullUpKing you put out content with a slight error just accept it nd move on, dont be a child
@ThePullUpKing3 ай бұрын
@AmpereNA lol Mann plss. Don't get on my channel with that bullshit. I'm showing in my video how I did the job. You said you leaking oil and blamed it on the sealant.lol I told you it worked for me. Now that sound like you didn't didn't some shit right. Don't blame my video, hater.💀🤣🤡
@patgraeme7756 ай бұрын
Great video, but my man tape of fill those intake runners off
@ThePullUpKing6 ай бұрын
Thanks. You mean what I did in the video?🤔 6:15
@patgraeme7756 ай бұрын
@@ThePullUpKing no , I meant stuff or tape the hole, tf is a loose dirty rag gonna do🫡
@ThePullUpKing6 ай бұрын
Tf u mean? It served its purpose. Do what works for you.🫡
@markwhitehurst4444 Жыл бұрын
Do i remove oil first???
@ThePullUpKing Жыл бұрын
Nope
@misterstealth92375 ай бұрын
Links to parts?
@ThePullUpKing5 ай бұрын
Got the gaskets from Autozone
@malikcarter1323 Жыл бұрын
That’s a lot of shit to do. You nice buddy, bmore
@ThePullUpKing Жыл бұрын
Facts. I appreciate that! Thank for watching!💯
@ChevyManTrell5 ай бұрын
Good video..The wire harness in the back is a BITCH TO GET AROUND‼️‼️
@ThePullUpKing4 ай бұрын
Mann u ain't lying! Thanks for watching!
@johnathansotomayor23997 ай бұрын
The area where the tube seals sit on the valve cover where gouged out. I couldn’t attach a photo of it here. So, I texted the pull up king and he answered promptly letting me know that it needed to be replaced. Shout out to bro for the prompt response ✊🏽
@ThePullUpKing7 ай бұрын
Yessirr‼️🫡😎💪🏾 Anytime bro
@dutch250510 ай бұрын
Bruh why they tell me $541 to replace mine 😭
@ThePullUpKing10 ай бұрын
Lol That's how shops do bro. They got a business to run. Be prepared to skin down with them. Especially the dealership
@x1pyroveride7 ай бұрын
Man that looks like a pain.
@ThePullUpKing7 ай бұрын
It is, but when you do a few, you'll get the hang of it.
@jaredlake3964 Жыл бұрын
Fuck man that looks like an 8hr job
@ThePullUpKing Жыл бұрын
Less than 3hrs for me.
@jaredlake3964 Жыл бұрын
@@ThePullUpKing you just took out 80 boats unplugged about 37 wires fix the problem, then put it back together for me. That’s more than 12 hours lol
@ThePullUpKing Жыл бұрын
@@jaredlake3964 💀😂
@alexzelaya73366 ай бұрын
Thanks brother u save me 500$ I just did it today took me all Day but I got it done and learn in the process u are a great ninja 🥷 👍
@ThePullUpKing6 ай бұрын
Nice job!💪🏾😎 I appreciate it man! Thanks for watching!👨🏾🔧