This is a quick review of the Vevor Portable Mag Drill, below is the product link for your use. VEVOR Magnetic Drill: s.vevor.com/bfQpTq Coupon code: VVPRO to save 5% off (used for all products)
Пікірлер: 29
@alanjackson439711 ай бұрын
The rack on the back of the head can be used to make infinite stop positions, using a piece of sheet metal with a slot on top of the housing drill and tap a screw hole to mount on the casting. Then you can slide it into any of the teeth on the rack to hold it in desired position.
@carlwhite822511 ай бұрын
Chuck, I bought one of these last year and using a Hougan 5/8 annular cutter i drilled 500 holes in my new home-made fixture table thru 1/2 " flat steel so I approve of this tool, it just won't die as I had expected it to. great home shop tool.
@AmateurRedneckWorkshop11 ай бұрын
Nice drill and well demonstrated. Thanks for the video keep on keeping on.
@CameronMcCreary11 ай бұрын
I've been looking for tool reviews on those magnetic base drills for quite some time. I'm going to take a close look at this one.
@mkegadgets438011 ай бұрын
I seen a couple people do the same review was on the same drill. I recently bought a Milwaukee one. At three times the cost. I am happy with paying their price. I like Milwaukee because I bleed red. I can’t afford cheap tools.
@manualman625211 ай бұрын
Nice looking unit...thanks for the review
@garysheppard402810 ай бұрын
I got this machine recently and am very happy with it. Same machine except mine's the 240 volt version. Does everything I need it to do.
@MrJmBecker4 ай бұрын
The very little Alen key is for adjusting the gib so that it stays where you leave it. Furthermore, when using the annular cutters , you should use coolant ! That's what the reservoir is for 😅
@TheAyrCaveShop11 ай бұрын
That's a dang good price point for a DIY mag drill... Thanks for the review 👍
@StefanGotteswinter7 ай бұрын
Man, I dont need a magdrill, i always wanted one, I have zero use for it. This does not help me to reduce my urge to own a magdrill :D Thanks for the demo!
@outsidescrewball7 ай бұрын
Too Funny, same desire and now I have 3 magdrills along with selling another unit that I had rebuilt from a dumpster. Thanks for viewing and all of your mentorship
@skipwaelty39746 ай бұрын
The gibb on the right side of the head can be adjusted to keep the motor from dropping.
@swanvalleymachineshop11 ай бұрын
Good one Chuck . A few of those drills getting around at the moment . Funny thing is , they are all slightly different drills . 👍
@outsidescrewball11 ай бұрын
thank for viewing and yes your comment is spot on
@frankward70911 ай бұрын
Looks good thanks for the review. Thanks for the video And by the way I joined the Is Closing lathe family 21" X 120"
@frankward70911 ай бұрын
CLAUSING lathe
@frankward70911 ай бұрын
Damn auto correct
@frankward70911 ай бұрын
That's one of the items on my wish list
@outsidescrewball11 ай бұрын
thanks for viewing and congrats on the Clausing lathe...
@1970chevelle39611 ай бұрын
I just did a review for them on a different product.
@roybertalotto63552 ай бұрын
When it screeches like that, your "feed" is too slow for the RPMs. Either slow down the RPMs or increase the feed. You can also tell by the chips that something was wrong...Nice channel BTW
@user-zw9cr3nx3p5 күн бұрын
What model is this magdrill,and is it a 220v
@b9255511 ай бұрын
Did you see how he used a stubby drill? Jobber length drills above 3/8 will not clear the base of the magnet. You would have to block up the bottom to get work under the drill. The drill chuck is an afterthought. Also on the one I bought the magnet would not hold in a horizontal position on 12 ga square tube. Not a bad unit for the price but does have limitations. This unit is designed for annular cutters. I would be very careful when using this in the inverted or horizontal position.
@ackattacker3 ай бұрын
No mag drill from any manufacturer will hold properly on 12 gauge steel. They’re supposed to be used on 3/8 and thicker, drilling I-beams and truck frames and the like. You’re also supposed to use the included safety strap because even if the magnet holds perfectly, a power interruption could drop the drill on your head.
@dannywilsher416511 ай бұрын
I bought the largest chicken pen that Vevor has available. It came in a box that was barely able to keep the pen contained. But the hardware to attach the door was missing. I have talked to customer service numerous times in the last 2 months via email and they assure me that my parts have been mailed. I finally made my own brackets and mounted the door without their parts. After over 2 months, I got tired of waiting. Really not their fault the parts didn't make it I suppose, but still... 2months?
@outsidescrewball11 ай бұрын
Thanks for sharing!
@robertlark775111 ай бұрын
Why not see if Vevor would pay you to write a proper operating manual.
@Watchyn_Yarwood9 ай бұрын
That is my biggest gripe with almost everything you buy today. Little or no operating instructions or written in Chinglish.
@user-wb6tw6uz5k6 ай бұрын
most of the instruction manuals are not even good for toilet paper