Vastex D-100 Conveyor Dryer Review + Hands On

Рет қаралды 6,660

2 жыл бұрын

This is a review of the Vastex D-100 Infrared Conveyor Dryer. An very small and compact entry level conveyor dryer that can be a great option for small to medium size print shops.
-
Vastex D-100 Measurements
Overall Length: 46"
Overall Width: 24"
Overall Height 24"
Belt Width: 18"
Heater Size: 16" x 16"
More specs: www.vastex.com/Literature/Inf...
-
Make sure you subscribe so you don't miss out on all things screen-printing and graphic design!
#creatornow #vastex #review #screenprinting #smallbusiness #d100 #tshirt #equipment
-
Follow NCA:
TikTok: / nca.ink
Instagram: / nca.ink
Twitter: / sansclients
Official website // Custom t-shirts // Merch:
www.nca.ink

Пікірлер: 19

@RichardMunoz1 2 жыл бұрын

Holy shit, you had me subscribing within the first minute. That dodge neon comparison had me dying! 🤣🤣

@ScreenPrintR 13 күн бұрын

I was skeptical about the review until you showed us the Toyota Yariz. I had one of those. Very roomy. Also saw plenty of Vastex D-100's at the many t-shirt-con's. Great job.

@MehaulUhaul 2 жыл бұрын

I love the digressions. :)

@printittowinit 2 жыл бұрын

Had the same issue w/ the belt on my Vastex conveyor dryer. You want to adjust the screw that lifts/drops the belt tension bar on whatever side the belt is moving towards. If it's moving to the right side, then lift the bar on the right side and vice versa. Just do it in 14/ or 1/2 turn increments. Do it during your next job and you should be able to find center with just a handful of adjustments. Hope this helps. Good luck!

@nca 2 жыл бұрын

Dude, thanks so much! I couldn't find any info on how to do this. I got it calibrated so it's not moving as much but I think I need to adjust it one more time to get it perfect. 👌

@alexkey717 2 жыл бұрын

Took about 3 hours to assemble. I can confirm, it was not a good time. Wasn't really that hard to do though.

@igotnopancakemix 2 жыл бұрын

Question: If im printing an all over print with water based ink from sleeve to sleeve would i get by folding the tee in half curing each half of the tee? Thanks!

@hakkieriksson9928 Жыл бұрын

Hi from Sweden! Im on my way to buy a D-100 and just wonder what you think of it after a years use? Plus and Minus? I never print stuff bigger than an t-shirt and folding isnt a problem.. but the fumes maybe? All the best, Tomas!

@sjmorning2 Жыл бұрын

That's speed and temperature you use

@jesusquiroz4887 Жыл бұрын

What are the best settings for the belt and heat controls?

@nca Жыл бұрын

Everyone will be different, it really depends. You just gotta play around with the belt speed and heat level until you dial it in. I have a temp gun that I use to check the temperature of the shirts as they pass through.

@daviddelatorre9430 2 жыл бұрын

Would you recommend this for DTG treatment and curing?

@nca 2 жыл бұрын

Sorry, I haven't tested it with DTG or anything other than plastisol printing so I'm not sure. I have heard from others though that conveyor dryers in general work really well for DTG curing and pre-treatment. Hope that helps!

@simseven4967 2 жыл бұрын

Dtg you cure with heat press, I cure waterbased inks with heat press

@266marie Жыл бұрын

@@simseven4967 I use my heatpress also but hate the press mark on the shirts

@LoyalToThePress 2 жыл бұрын

😂😂😂

@simseven4967 2 жыл бұрын

Waterbased inks are way better than plastisol and you have many options on the market, plastisol is not environment friendly and probably will be some issues in the future