Mine just needed pushing in. Many thanks mate, really helped me out when I don’t have much money.

Absolutely spot on. To the point, no fluff and accurate - just what I needed and saved me from trying to access the back of the switch. Many thanks Jon

Video spot on, a big thank you for taking the time to do a first class job

Thanks for this, very helpful,my daughters Corsa D had the same problem,removed the resistor and one of the pins was corroded slightly,cleaned it up and it worked fine again.

Great video. Unfortunately this was a long job for me due to various problems with the connector plug but I eventually got it solved. Without this video I wouldn’t even know where to start. Big thanks!!!

Thanks bud - thanks to this video got my first ever car repair done myself! Really clear instructions.

Thanks for video. Got resistor off Internet for 12 quid including P&p and managed to fit myself. Only fiddly bit was getting the screw in and out. Now the heater works as normal. Saved me quite a bit of money as garages quoted between £50-£80 to replace it. If you have the same problem with your Corsa, I would recommend you follow this video and try do it yourself. If I can do it, anyone can.

Thank you Anton! The video was spot on mate! Very clear, short and precise 👍 I've managed to replace the heat resistor and heaters are working perfectly fine.. Muchly appreciated!

Perfect. My wifes new car is a 1.2 litre Energy. Has just this problem and now I know exactly how to fix it, Most certainly deserves a like and subscription.

Cheers chap just fixed mine after watching this ...i pulled the plug out and pushed it back in and it now works spot on... ..thanks again ill remember this fix

thanks very useful information - just happend on mine wondering if this is common fault on corsas. never heard of it happening on other cars. thanks for posting

Had the same issue. Ordered a new one off amazon along with a 5.5mm socket. 5 min job all good. Thanks alot for the heads up. The only issue i had is that one of theblocating lugs was off so had to carefully grind it off. Popped in a treat.

Great video, took me an hour to find a socket to fit and get my massive body in the footwell. 5 mins to change

Hi Anton, I really congratulate you for the clarity with which you explained everything....in particular, the technique with which you extracted the resistor from its housing...really GOLD advises for me as I'm just a neophyte! !! Thanks again

Perfect. I have just sorted my father in laws heater using your video, thanks. FYI, his bolt was slightly bigger than 5mm so used my pals 7/32 spanner and all sorted, so thanks very much for posting.

Thank you so very much, no more freezing cold hands for me now, well done, your video was very clear and the unit was so simple to swap.

Thanks so much! Managed to contortionist myself into the footwell and do it, blower now works. So chuffed 💃🏻

Daughter very happy now fan fixed on her car. Great tip about clips and how to get resistor out. Thank you

My car heater was only working on 4 . After i changed the resister it works on all now . Thanks for upload it really helped and saved my some dosh.

If you have a left-hand drive car (i.e. Opel) then the resistance must be pushed to the right when you take it out. It's a really good video. The bolt that holds the resistor is actually a 5.5 mm, completely idiotic, but I got it out with a spanner and a pair of pliers as I only have keys in whole mm. Thanks for the video mate.

Great - many thanks, my daughter and her Corsa D thank you for saving her from the "Max or nothing" syndrome :)

Great video! Just followed this and my blowers are working perfect! Wish I had seen this video a year and a half ago when they first stopped working properly!

My corsa van heater played up this morning only speed 4 working! A big Thankyou for the video as this is my job this week saves me booking it into a garage Cheers fella

Brought the new part from Amazon. Unplugged the old one. Realised I don't have the right tool to remove the old one. Plugged back into the old one. It's now all working again 🤣 I've wasted £9.99. Great video though keep up the good work.

Thank you very much for this tutorial, it helped me soo much. I recommand this video to everyone who has this problem, thanks again!!! Liked subscribed.

Good video but when replacing it do bear in mind the mileage the vehicle might have done. I'm at 150K and I'd already replaced the resister bank quite some time ago and when the fan would only run on 4, thought I know exactly what it is (had the same on a Citroen). Swapped it out but while driving the 5 miles into town, I started to get a nice burning smell into the car. I switched the fan off! I have just taken out the fan and it runs reasonably well on pos. 4 but doesn't turn at all on pos. 1 and not much better on 2. And spinning the fan I'm lucky to get one revolution. Bearings are shot. So yes, you might get away with replacing these resisters (its an easy fix) but it isn't always the problem. Btw compared to the Citroen replacing it on the Corsa is a walk in the park.

Good video, straight to the point and no rabbiting on for 10 minutes,

Great video and my Vauxhall Corsa van has the problem. I will be following your instructions and and will let you know if I am successful. Cheers

Thanks for this. I will try changing it myself once the part gets delivered.

Great video,this has saved me £50.00 at the garage,many many thanks top job....

Thanks . Knew what the problem was but now I know where it is

Thanks!! seems like my plug just had some dirt in it. I removed it, blew the connector out with some compressed air and works perfectly now!

Thanks for the good explanation. I managed to fix it. it was explained very factually and easily. nice greetings from Germany 👍👍

Thanks so much for the video, currently have the same probem only works on 4

thanks pal, managed to replace my heat resistor today.👍

Best video.BEFORE REMOVING THE PART TRY TO SHAKE IT- contact might be the issue as the part is located at the passenger feet

Thanks - very clear. its the third one thats failed over about 8 years - so looks like a common fault

thanks saved me a few bob on garage fees. part cost £5.49 on ebay . the tip about the two awkward plastic tangs (not mentioned in Haynes Corsa D manual) was useful in removing/refitting

This has just happened on me today, thank god for this vid, I'll be sorting it out myself now 👌

Thanks again mate. Unfortunately for me this is the second time referring to this video as the previous resistor didn't last long

Thanks a lot mate, especially the clear footage in such a nightmare of a spot to work in was very helpful. Cheers!

Managed it in about 10 mins. Hope it lasts a bit like. Excellent video mate.

Great advice on replacement done and dusted 10 mins tks

Great video, i actually did not know where the resistor was until this video so i just banged mine for the meantime with my hand and it works 🙂😁

Excellent. Top man, I was scared that I would probably have to replace the fan.

Watched this video, done the job in 10 minutes, (im 6' 2'') note to self take the seat out first next time, thank you aaanton11, thank you very much, love my corsa again !!!!

Exactly what I needed, and brilliantly explained. Thanks very much!

Top man! Probably saved me a few hundred quid at the garage. Thanks!

Just did this for my 2012 hatchback Corsa d, it worked thanks so much!

This was very helpful. I managed to change it myself. Thanks so much for the video!

I have the same issue thanks for the video mate reallly appreciate it

Thanks mate. Saved me a good £50 if I went through the garage!

Love your video my friend. I just changed mine following your tutorial. Wonderful video; very informative helpful!!

I had same problem and when I unplugged and plugged the wiring into the resistor it sorted itself. Just to say try that first before full resistor replacement

Mine just needed a little push and started working , cheers mate , really appreciate it 💯 had to subscribe

That's wat is called professional video and support

Very helpful , thanks from Italy

Top man Anton, video was spot on 👍🏻

Just did for my corsa E. Thanks for the video!!

Thanks for demo ,great help.now know how to do it myself

Did the job,fiddley but your video was very helpful Thanks you😎

Thank you mate. You helped me do the wife's car today 👍🏼😎💪🏼

Thank you aaanton11!! Saved me some money going to garage! Greetings from Croatia!

Worked perfect, part cost £7 on eBay. Nice one 👍

Thank you, I’ve got same problem exactly .

Fantastic 👏👏👏👏,Very helpful changed my today Thanks👍

Thank you so much very easy vedio to follow you saved me money. God bless you

My car had the fault, and now, with this video it fixed at NO COST, because it was oxided contact points which caused the fault. I used a contact spray can, and took care to cover the parts so I did not spray the hole compartment.

Absolutely brilliant video well explained thank you

Great tutorial, many thanks.

Thanks so much for the help first time fixing a issue thanks for the clear help

Same problem here, thank you very much.

Thank you, this clip is very helpful ,great effort

5.5mm socket is actually correct but thanks for the how to!

Thanks a bunch. Awesome video. Cheap fix

Thank you, job done in 10 min !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Big Thanks just fix my corsa.

Make this man prime minister

Brilliant Thank you , can get my heaters sorted now. Owe you a pint sir. 🙏☘️

Thanks! I'll order my replacement today

Thank you so much for this and so easy to understand too you kind person

Oh my goodness me, my local garage charged me £200 to do this! I'll be referring to KZfaq for all my future faults!

Thanks for the video man!! Made me save like €100,-👌

Amezing video..very useful..Thank you

Thanks very much did my self and saved a lot of money 👍

Thank you!! Great video! Going to try this tomorrow

You're a great problem solver. What if all the fan speeds work fine, but, only one of the various heating outlets, brings out the hot air?

FABULOUS- Thank you for your work. Informative and practical

Thanks Bro, you just saved my ass ❤

Cheers for this video. Got mine sorted 👍

Thank you very much for this very good video. I've must resolve now this problem, too and this clip is perfect to replace this resister on my own. I learned that there should be different values ​​of resistance (or does it not matter?). Which one would be for a 2011 Vauxhall Corsa (german production)? Best Regards from germany.

Great video 👍

Thanks a million. Your shared content was helpfulness.

What tool do I need to take the old one out because it isn't a normal screw thank you

Great video helped me massively thank you

Great video just some advice…get it from Amazon, is just 8£ rather than 33£ on euro car parts.

great , thanks a lot !! Gus

Thanks for uploading this info. Worked for Vauxhall Adam too. Had a lot of trouble getting the after market replacement part (number- 13248240) to fit though. Would not sit flat in slot. Ended up cutting one of the left plastic pips off in order to get it to sit in place. Thanks again.

Thanks for this - mine works on every setting EXCEPT 4, any idea if it's the same issue?

Thank you 👍👍👍👍👍👍