No video
Vauxhall/Opel Meriva 1.6. Engine ECU replacement, reset and programming.
Рет қаралды 97,962
Күн бұрын
@yiannakosautomotivekeys2380 2 жыл бұрын
Hi everybody. I had a same situation today. Replaced the ECU (Engine computer Module) on an Opel Combo 1.7 diesel. I managed to program everything as per video, the immobiliser light stop flashing, all DTCs were gone and when I tried to start the car everything was died. No crank, no start. I thought that the battery was very low, boosted the battery and nothing changed. I'll give it another go tomorrow and hope it will work. I thought to share my experience here. Great job Luis, helped a lot. keep it up and thank you for sharing.
@LMAutoRepairs 2 жыл бұрын
☺ Hope you get it sorted! 🤞
@inchaseable1 6 жыл бұрын
I've downgraded my firmware to v1.39 and it managed to read the cluster. thanks very much for linking me to the video LM.it has worked a treat.
@LMAutoRepairs 6 жыл бұрын
Inchaseable One That's great news! Glad I could help!
@irshadjamaldeen2495 6 жыл бұрын
Thank you very much for the video. works like a dream and saved me from expensive repair. I followed the exact procedure and all went good. I tried the Opcom 2008 and went through all the process. However, i had problem with resetting the instrument cluster. Finally, upgraded the software to Vauxcom and managed to finish it. Thanks for the video. Very useful
@LMAutoRepairs 6 жыл бұрын
That is fantastic! Thank you for the feedback...
@daffysplace3483 5 жыл бұрын
great tutorial. worth every minute of viewing. thanks mate. i have a 2006 meriva. iv tried loads of tricks to reset the service light but no luck lol going to buy a handheld code reader see if that will reset light.
@Parknest 6 жыл бұрын
Luis, I had a P1610 on a 2004 Corsa C after I'd stupidly reset the ECU on OP COM. I just programmed the immobiliser and it worked a treat.
@LMAutoRepairs 6 жыл бұрын
Parknest That's great, thank you for watching and for your comment!
@mohamedrahib7685 7 жыл бұрын
I don't know what to say .thanks for this interesting video .even if I found it hard to understand what you did but I will watch it for second and third time until I understand it thanks my brother god bless you.
@LMAutoRepairs 7 жыл бұрын
mohamed rahib Thank you for the comment, really appreciated!
@marviscyriaquebah3821 2 жыл бұрын
@LM Auto Repairs, thank for your meticulous guidance. I am facing a similar problem on my Opel Vectra c 2002 in Africa. Need to get in touch for support.
@LMAutoRepairs 2 жыл бұрын
To replace the ecu, the procedure is similar... 👍👍
@conradwallace3404 2 жыл бұрын
Thank you so much for this video, I have an Astra H and will be doing this soon. I only wish I knew how to do this a couple years back considering I needed the same on a corsa D and forked out hundreds to do this same process. Thank you very much again for this detailed video it’s great help
@LMAutoRepairs 2 жыл бұрын
😊 👍👍👍
@faisalbayashot443 Жыл бұрын
Hi I have the same car with the same Engine. Om getting a fault code 1482 I checked the fan relays but all seems ok The fan will run only when the temperature gauge reach to the middle. The spanner with wrench signals appear and disappear always . I would appreciate it if you could help Thanks
@sheledmikymo 5 жыл бұрын
just reset dash and now all working, thanks for the tutorial,
@LMAutoRepairs 5 жыл бұрын
That's great! Thank you for the feedback and for watching!
@sholter42 6 жыл бұрын
thx for this great video. it helped me so much. my meriva is on the road again and my self confidence raised about 120% ;) don't know what to say more...go on doing these great content :)
@LMAutoRepairs 6 жыл бұрын
DerDoc_der_echte That's great, thank for sharing you experience! And thank you for watching obviously!
@furkansyuleyman485 3 жыл бұрын
Thanks for the video. After 3 years of uploading the video it still helps people. What are the symptoms of a not properly working ecu?
@LMAutoRepairs 3 жыл бұрын
Hi Difficult to tell, as they can fail in many different ways... Proper diagnostic is needed to completely blame the ecu as being faulty... Thank you for watching and for your comment!
@furkansyuleyman485 3 жыл бұрын
@@LMAutoRepairs thanks mate
@furkansyuleyman485 3 жыл бұрын
Hi Is it possible to reset the immo ring around your key? I think that my ring doesn't detect my transponders Thanks
@LMAutoRepairs 3 жыл бұрын
@@furkansyuleyman485 The ring is just a coil... not resettable... But could be broken, an open circuit... You might need to open it to check... Do not obviously disclose the key as the problem... test the key... Thank you for watching!
@furkansyuleyman485 3 жыл бұрын
@@LMAutoRepairs thank you for your reply. Is it possible to replace it?
@cristi9944 3 жыл бұрын
Hello, I would like to ask you how much I have to pay to learn this whole procedure of copying data from the old ecu and rewriting them in the new one. I guess it is valid for any car model. Thank you very much.
@markhouttuin2896 2 жыл бұрын
Perfect my car is running thx
@LMAutoRepairs 2 жыл бұрын
😊 👍👍👍
@fam.a-r9140 3 жыл бұрын
Great tutorial. Worth every minute of viewing. Thank you very much, i didn't find any video about this in the german youtube. Can i make this with opel corsa c 1.0? And how can i get the pin code if i dont have carprog?
@gvvq-pi5ml 7 жыл бұрын
Well people can say what ever they want, at the end of the day you got the job done and it works ok....
@LMAutoRepairs 7 жыл бұрын
Frederick Shead Wise words! Thank you for watching and for your comment, much appreciated!
@colinlyne1660 7 жыл бұрын
Hiya another great video fella. I am not sure I can keep up with the fast movement of your screen changes. I would have to watch the video many times which I can do. As you have been helping me with my grandaughters Agila Im going to say I took the fuel tank out of the vehicle and pressure tested the pump off the vehicle. it showed it as before at 7psi running it directly from the battery which I had taken off the car. i initially saw it pump fuid from where it should and although it worked it seemed weak so then the pressure tester was fitted with the earlier. result. I had wached a video of some guy breaking a fuel pump apart and illustrating all the other parts within the fuel pump assembly. namely filter pressure regulater and realised i should have bought the whole assembly and not just the pump. A costly mistake have a new assembly coming sometime tomorrow. I am not sure it will work in the car due to possible ECU control issues so I am going to test it off the car again tomorrow, before putting it back. This is due to the fact that since I changed the engine I have not heard the initial 3 second prime. I would be interested in your view. many thanks for all your producing for interested guys who love cars and electronic control cheers colin
@LMAutoRepairs 7 жыл бұрын
colin Lyne I don't think you will have any issues with the control side of things... The ecu only controls a relay, which in turns runs the fuel sender pump... Until now everything points to a bad pump... Also check that the relay is good... Bear in mind that just because you can hear it clicking, does not mean is good...
@AlanAnsell 5 жыл бұрын
got a ecu kit but its off a auto do you need security code to change it to manual with opcom
@LMAutoRepairs 5 жыл бұрын
Hi Not sure... but I thing you don't need the pin for that... Thank you for watching!
@mik7233 2 жыл бұрын
hi everybody! i bought a brand new ECU for my vauxhall astra 1.7cdti with the same part number as old one,but i dont know if the new ECU"s come out from factory with the software already written on it ,or it need to be done by a garage technician, if yes then how to program it to my car??? its enough if i have the security code of my car? yhx!
@zsoltcsaplar8054 2 жыл бұрын
Thanks to this video, help a lot! I have same car, same year's:, fault I have after Actronics. no company repaired Ecu, Bcm, key immo ring, Is B3058 vehicle not programmed identification, U2105can-bus communication with engin control unit, B2961 W terminal low voltage, P1616, P1615,,, 174 coolant temp sensor can signal not okay. I have no knowledge what it is? Car not start,
@LMAutoRepairs 2 жыл бұрын
Hi The U2105... can you communicate with the engine ecu? 👍👍👍
@iozel4633 5 жыл бұрын
Hello mate, thanks for the video. I note you mention about Opcom being affordable. On ebay they are on sale for £15-£20, but I think you previously stated that yours is a different more expensive Opcom. I think it would be very helpful to lot of people if you could explain what the difference between yours and the ebay ones is, and perhaps let us know where/which we should get so that we can follow along with your videos? Thanks again. :)
@LMAutoRepairs 5 жыл бұрын
Unless you get the genuine one, they are all pretty similar... The ones with the pic chip can be flashed is something goes wrong, which is a good thing... But you can also find them on eBay... Thank you for watching and for your comment! 👍👍👍
@gurmanlall8247 3 жыл бұрын
Hi good news followed all the steps all lights off engines starts ok. But have a problem with the cluster i dismantled the cluster and the dials for the rev counter is not working may be they are not fitted correctly any how i have another cluster can i just reprogram the cluster through instrument on vaux.com will it work fine. Many thanks.
@inchaseable1 6 жыл бұрын
excellent video. but just wondering if you buy a ecu that has been reset .you don't need it's passcode number.is that correct
@LMAutoRepairs 6 жыл бұрын
Correct....
@infomecanicos6702 2 жыл бұрын
woow mister hi from Ecuador country
@LMAutoRepairs 2 жыл бұрын
☺ 👍👍👍
@patrykzareba6846 7 жыл бұрын
even with my bad English can under everything....I got ecu problem I will try sort it all by myself....nice video...it's very clear video...it's just wonder to know how I can get op come and where ....? thanks
@LMAutoRepairs 7 жыл бұрын
Hi Thank you for your comment... There is loads of places where you can get opcom... a quick google search will show you...
@clustermaster8456 2 жыл бұрын
Another great video Luis, thx for sharing. I have 2 questions please... 1) After successful programming & car starts again, does the new ECU pin code change to match the rest of the modules? 2) Let's say I forget to activate ABS (for example) in variant config, can I still go back into the system and activate it? Just curious as this video answered many questions for me 😊
@LMAutoRepairs 2 жыл бұрын
Hi It is yes to both of your questions... 👍👍👍
@gurmanlall8247 3 жыл бұрын
Hi could u please tell which would be ok to use because like im your video u say instrument successfully programmed my one doesnt do anything if i buy the version 1.99 would this do it for me many thanks.
@Trist1975 6 жыл бұрын
Thank you for taking the time to do this vid. I have replaced the abs module/pump on my Corsa D VXR with a second hand ABS unit as the original ABS unit was non repairable. The second hand unit has been tested and comes with a warranty. The ABS that has been replaced requires programming. The part numbers on both ABS units are compatible and I will be using an OPCOM to program. The issue is i have never programed an ABS unit. Do you have a video on how to program or instructions on how to do this? Any information will be appreciated.
@nickhollingsworth3537 2 жыл бұрын
Great video ! Thanks ! Can anyone plz tell me - does the OP-COM software need a specific OBD2 reader (ie the hardware) ? I have a 2003 Holden Combo XC (Opel Combo C rebadge) and plugged a Carista bluetooth OBD2 reader and plugged it in but it doesn't seem to work
@LMAutoRepairs 2 жыл бұрын
Hi Yes, it does need... you can get the VCI relatively cheap... 👍👍👍
@gurmanlall8247 3 жыл бұрын
Hi as we were dicussing the complete kit i have fitted immobiliser clocks engine ecu etc the car is running but with the vin no of the car it came from now if i put the vin no for my car will i need to reprogram the bcm immobilser etc will the car still start.
@LMAutoRepairs 3 жыл бұрын
Should do yes... Change the vin on all the modules...
@ibrahan7680 2 жыл бұрын
Very good job !
@LMAutoRepairs 2 жыл бұрын
😊 Thanks! 👍👍👍
@tonycalow708 7 жыл бұрын
Not only heat damages electronics, but vibrations from the engine causes the damage you talk about. Vibration is probably more responsible than heat.
@LMAutoRepairs 7 жыл бұрын
Anthony Calow Probably... Thank you for watching!
@giuseppegiuseppe8796 5 ай бұрын
Ciao a tutti! Ho un grosso problema da risolvere. Ho un Opel Combo 2004 1.7 diesel. Ho perso il transponder e non so come fare! Posso disabilitare per farla partire con la chiave senza transponder? Grazie
@dieytube Жыл бұрын
Hello, first of all thanks a lot for waste your time trying to help us doing these videos. I have the same car but with the Z16XE engine nad of course with the same problem, i live in Spain so imagine how is the poor ECU with our temperatures this summer. I'm trying to repair my ECU but in case i can't i have one question. My ECU is the 12214830 HSFI 2.5 DXBC, and i've found exactly the same but DYDT, could i change it?. Thanks again for your time and help.
@LMAutoRepairs Жыл бұрын
Hi Is never a waste of my time... I enjoy sharing and help others... If the ecu is from an identical engine, I would say it should work fine... 👍👍👍
@user-wk5iu9bi9b 5 жыл бұрын
Thank you for your great video tournament, nice work. I have a question here, what if I just replaced the ecu and body control unit, and dashboard plus the security sensor unit and key chips with the same car model, then shouldn't I have to do the computer recoded and reset, is that correct?
@LMAutoRepairs 5 жыл бұрын
The procedure would be similar... reset the one to install and then program it using the pin of the car... Thank you for watching and for your comment!
@user-wk5iu9bi9b 5 жыл бұрын
@@LMAutoRepairs Thank you for your kindly reply and turly appreciate that, have a great day.
@LMAutoRepairs 5 жыл бұрын
@@user-wk5iu9bi9b 👍
@pauldavies3612 4 жыл бұрын
When I come to reset the IPC I have no programming button and it is cycling through IC=00 and slowly makes its way to IC=37 before saying there is a communication problem.
@Venom-eo7om 4 жыл бұрын
SAME HERE
@gurmanlall8247 3 жыл бұрын
Hi if u reset the ecu using opcom how can u still read the pin by using carprog.
@LMAutoRepairs 3 жыл бұрын
Hi To reset it you need the pin first... Thank you for watching!
@fernandoveloo22wso29 2 жыл бұрын
Hi! It looks like I have the same problem with my vauxhall meriva 2010. It's running but it has no power.. how will going to help me if ECU is the problem, and how much it will cost me if we replace and program it?
@LMAutoRepairs 2 жыл бұрын
Have you scanned the car? You need proper testings before condemn the ecu... Thank you for watching! 👍👍👍
@gurmanlall8247 3 жыл бұрын
Hi once you retrive the pin from car prog then reset the ecu can you still retrive the pin again from carprog or is there another way
@LMAutoRepairs 3 жыл бұрын
Why do you need the pin once reset and once you know it? I never tried... I know that the pin is not erased.. you can retrieve it with a programmer... but never tried with carprog...
@wolfie_7778 7 жыл бұрын
Many Thanks for your knowledge and a very interesting video's
@LMAutoRepairs 7 жыл бұрын
John Paul Wolfe Thanks John, for watching and for your comment!
@djbillc123 4 жыл бұрын
can you tell me how to reset service milage with a opcom
@sanchopanza1312 3 жыл бұрын
what version of opcom? 1.45 already swore at IPC
@LMAutoRepairs 3 жыл бұрын
I have 2 versions... But believe I was using the 1.45 on this video... Thank you for watching!
@gurmanlall8247 3 жыл бұрын
Also the pin code for the second bit i have got the car pass code is that ok.
@LMAutoRepairs 3 жыл бұрын
Yes...
@raylyd 5 жыл бұрын
Thanks now when i get a replacement engine i can program a spare ecu :)
@LMAutoRepairs 5 жыл бұрын
That's good... Thank you for watching and for your comment!
@shefi14 7 жыл бұрын
thanks for the video very helpfully . what do you think about Abrites, can i get the pin code with Abrites and programme a second hand ecu?
@sadikmamoun2847 7 жыл бұрын
thanks man, great video by the way learn manythings from you
@LMAutoRepairs 7 жыл бұрын
sadik mamoun Thanks for your comment!
@tattoos1988 3 жыл бұрын
Hi I understand your video great explanation and detail by the way when you put the new ecu in and used the retrieved code how did you get it so you used the original cars code thanks
@LMAutoRepairs 3 жыл бұрын
All in the video... you must have skipped it... 👍👍👍
@patrickcaia3544 Жыл бұрын
Hi mate What version opcom do you use? My China clone will not connect to instrument cluster. I have a 2003 combo c Your help will be much appreciated.
@LMAutoRepairs Жыл бұрын
I have a few different versions... You try a different one... 👍👍👍
@husseinolivia2548 7 жыл бұрын
GREAT JOB MAN thanks for sharing
@LMAutoRepairs 7 жыл бұрын
Hussein Olivia Thank you for watching and for your comment Hussein!
@peetekastanis9587 7 жыл бұрын
A small university. Thank you again for the detailed tutorials. Many people are learning from you. Now here is my question. In my car, a Peugeot 407 hdi 136hp, last year, I changed keys and door-locks, in the authorized dealer. The PIN number I was given for the new keys, is different from the old one of course. Right now, I managed to read my EEPROM, and saw that the original PIN was still there. The same one. Now, what have they done? Did they changed the PIN only in the BSI? And if there are two different PINs, how can that be? Does the PIN in BSI take precedence over the PIN in the EEPROM? My ECU is Siemens SID 803.
@LMAutoRepairs 7 жыл бұрын
Peete Kastanis Hi I needs to be only 1 pin... If at the dealer they have changed locks and keys, was no need to change remotes... have they? Even if the remotes were changed, they would have been programmed to the BSI using the actual car pin code... Unless they have a also changed the BSI... even in that case, the new BSI would be programmed using the original pin... So, you can't have two different pins for the same car... What you might have been given, is the mechanical key number... that is a unique number that can be used to cut the key even if you don't have a key to copy from... Unless there is some info missing here... Hope that helps...
@peetekastanis9587 7 жыл бұрын
Thanks Imsvvavr My case is going to be a mystery, until I solve it. Last year, somebody got into my house and stole me. He also took away the two keys of my car. One with remote control and a simple one. So I took the car to the dealer with a transporter truck, and ask him to change the door-locks and the keys, just in case the burglar finds my car parked in the street and takes it away with the original keys. I tell you, that they changed the mechanism in the wheel column where the key enters and the door-lock plus the glove box lock and gave me new remote and simple key. They did not change the BSI. Now, my original keys, they have a card with the key code YU4V, which is the same with the PIN code my EEPROM has (I read the EEPROM with Galletto). It is located in the hex places: 22, 23, 24, 25. My new keys have a card with a new number: WXWB
@LMAutoRepairs 7 жыл бұрын
Peete Kastanis OK... I got you... I don't know why they would give you another code... I mean, they could have reset the ECUS to change the original pin... Although does not make sense that the code you have retrieved is different.. Do you have PP2000?
@peetekastanis9587 7 жыл бұрын
Well, I spent all my afternoon in my car with Diagbox, making various tests, and I think I solved the mystery. There is an option in Diagbox: REPAIR-->BSI-->PACK REPAIR-->REPLACEMENT PARTS (Or LEARNING, I forgot)-->CHECK OF THE CODED ENGINE IMMOBILISER CODE IN THE BSI, which accepted my original PIN, the YU4V. It seems that the new one, is about the key and how to cut new keys if they are lost, just as you mentioned dear friend. Once again you were very accurate and informed. How can I thank you. You are always right. Thank you for your time. Be happy!
@LMAutoRepairs 7 жыл бұрын
Would have to be something along those lines... Glad you got the mystery resolved... I am not always right... believe me.... lol Thank you for your feedback!
@ljr1981 3 жыл бұрын
Hi there I've got to replace my whole ecu kit ie immobiliser clocks bcm if I swap everything do I need to reprogram is it just plug and play also do I need to get matching part codes thank you 😊
@LMAutoRepairs 3 жыл бұрын
Why replace everything? Why don't you just replace the faulty module?
@ljr1981 3 жыл бұрын
@@LMAutoRepairs its the immobiliser that is broken and I can't seem to get a new one programmed
@georgetzelios7049 4 жыл бұрын
Hi i am replacing the ecu as its faulty i have followed your video exactly,i used carprog got the pins for ecus and reprogrammed the ecu.My problem is wrong instrument cluster id.I tried to reset this using opcom and but it doesnt work as in your video.can you please suggest what to do next.Can the instrument cluster be done with carprog.
@LMAutoRepairs 4 жыл бұрын
Not with carprog... Op-com should do it... Thank you for watching!
@georgetzelios7049 4 жыл бұрын
I used opcom and it fails at the reset ipm and program ipm
@LMAutoRepairs 4 жыл бұрын
Try a different Op-com version... I am not sure which one now, but some have some trouble doing certain procedures....
@georgetzelios7049 4 жыл бұрын
Can you share another version of opcom for me to try
@kamlon10 5 жыл бұрын
amazing video, just a question do you use carprog with the opcom device or I need to buy a carprog device
@LMAutoRepairs 5 жыл бұрын
Yes... you need a carprog device... Thank you for watching and for your comment!
@catalingherzan3829 4 жыл бұрын
Carprog is not a device ... just another software like opcom ...
@vilnisberzins4512 4 жыл бұрын
@@catalingherzan3829 Absolutely right - just another software with it`s own interface - in other words: a device ;-). You are welcome to check the manufacturer`s website www.codecard.lt
@kasapis6 7 жыл бұрын
Great info thanks can you make a video on how to program a band new ECU . not a second hand one but a brand new one
@LMAutoRepairs 7 жыл бұрын
Stephen Kasapis Hi I can if whenever it happens... Although the procedure is the same as from when the second hand one is reset... which at this point is as if it was a brand new ecu... or nearly... Thank you for watching by way...
@kasapis6 7 жыл бұрын
Ok thanks . but I sure if you had a brand new ECU you have to down load the software from OPEL not a second one because the second hand one already has software on it .
@LMAutoRepairs 7 жыл бұрын
Stephen Kasapis Ah... that.. yes, like I said, I will make a video if I have one to do... Thank you.....
@BERESHIDA2008 3 жыл бұрын
Great dedication , just to sum up , if i buy a 2 hand ecu for my opel combo c (best if i have a security code ) otherwise i will need a program like carprog to retrieve the security code from the old ecu right?
@LMAutoRepairs 3 жыл бұрын
Yes... Unless you buy an ECU already reset... Thank you for watching and for your comment! 👍👍👍
@ericarendshorst7228 5 жыл бұрын
Great video! Is it possible that when a Combo 2003 17 dtl gets the faultcodes P0610 and P0602 when the battery was empty and won't run anymore?
@LMAutoRepairs 5 жыл бұрын
You need to get the ecu reprogrammed.... Those codes are for errors in the ecu data... most likely will not fix it self... Hope you get it sorted... Thank you for watching and for your comment!
@ericarendshorst7228 5 жыл бұрын
LM Auto Repairs , thanks. I gonna ask Opel for the pincode and try to reset and program the ecu, instrument en immobilizer with my snap on modis or Hella mega max. I’ll let you know.
@LMAutoRepairs 5 жыл бұрын
@@ericarendshorst7228 Try that... but I think you need more than that... The reset procedure resets the immobilizer code only... I don't think will fix your problem... What you need is a complete reflash of the module... you need global tis with tech2win... or a tech2... Hope that helps...
@ericarendshorst7228 5 жыл бұрын
Indeed. the ecm had a reflash, and it is working again, the generator was defective, the cause ( according to opel) was perhaps a sudden voltage raise. We replaced it. Thank you.
@LMAutoRepairs 5 жыл бұрын
@@ericarendshorst7228 That's great! Thank you for the feedback! 👍👍👍
@TommasoBocci 7 жыл бұрын
Nice video, as always!
@LMAutoRepairs 7 жыл бұрын
Tommaso Bocci Thank you so much for watching and for your comment!
@fernandopistone2338 6 жыл бұрын
hello, you say that with the autel 908 you can do the adaptation of the ecu? Would the pin read it with carprog?
@LMAutoRepairs 6 жыл бұрын
Fernando Pistone The MaxiSys can indeed do adaptations etc... It can read the pin on the Corsa C... just like Op-com... Carprog can do much more... pin read... I mean.... than the MaxiSys... Thank you for watching!
@egzonqerimi1521 3 жыл бұрын
Hi i want to ask you something i hope u write me I have problem with that part of meriva i have the same meriva 1.6 16v ecotec but not vauxhall and it stop running any time im on road and can’t take the acceleration soo the question is (does it have any problem if the number of my computer car is not same with the new computer I appreciate if u write back thank u )
@LMAutoRepairs 3 жыл бұрын
Possibly... You need testing to see if is indeed the ecu or not... Thank you for watching!
@npr7649 5 жыл бұрын
Hi my vuax_com wont connect to BCM its saying ecm no reply wait 2 seconds
@LMAutoRepairs 5 жыл бұрын
Try a different software version... Thank you for watching and for your comment!
@op-tim_auto 7 жыл бұрын
What diagnose hardware did you use?? OPCOM/VAUXCOM interface(hardware) works as a replacement hardware for carprog, or what?Nice job! Thanks!
@LMAutoRepairs 7 жыл бұрын
Opel Corsa Hi No... carprog is one tool, opcom/vauxcom is another one....
@op-tim_auto 7 жыл бұрын
lmsvvavr yeah, i know, but i've seen you swaping between opcom and carprog in the taskbar,and there's only one OBD II port in the car, so??
@LMAutoRepairs 7 жыл бұрын
Pork Corsa So... you swapped them...
@LMAutoRepairs 7 жыл бұрын
Sorry I have deleted by mistake your last post... Of course I did not tapped any other OBD port on the car... Have you actually watched the entire video?
@minask073 5 жыл бұрын
hello.can you help me. i made step by step as you in video but i am stuck in ipc reset. write failed. my dashboard km not working and immo light not working.what can i do? thanks from Greece.
@LMAutoRepairs 5 жыл бұрын
Difficult to say... just try everything again... Reset all and start from the beginning...
@minask073 5 жыл бұрын
thanks. i change the ecu. i buy another one and i start from the beginning.
@jamessealey5608 6 жыл бұрын
Great video, thank you. I have a couple of questions though. What interface are you using to read Security Code from ECU? CarProg interface? Does OPCOM communicate through the same interface or do you need an OPCOM interface too?
@LMAutoRepairs 6 жыл бұрын
Hi Yes, Carprog interface to read the security code... and indeed you need a opcom interface to use opcom software... Thank you for watching!
@jamessealey5608 6 жыл бұрын
Thanks, I have Opcom already, and I am pretty confident about setting up new ECU, but I just need to be able to read Security Code from existing ECU (as we don't have Car Pass) and also from the replacement ECU as ebay seller doesnt have it. Can you recommend where to buy Carprog interface?
@LMAutoRepairs 6 жыл бұрын
Ebay can be a good place, actually I bought my one there... Just look for seller with a good reputation...
@przemekfryc5495 Жыл бұрын
Great job, could you tell where can I get this software and interface from?? To ecu swap and programming. Because last time I could not do with my autel. Thanks
@LMAutoRepairs Жыл бұрын
Cardiagtool.co.uk I HAVE NO AFFILIATIONS WITH THIS WEBSITE. BUY AT YOUR OWN RISK 👍👍👍
@przemekfryc5495 Жыл бұрын
@@LMAutoRepairs thank you mate, it’s that one you bought from?
@LMAutoRepairs Жыл бұрын
I don't remember now... I bought my one years ago... 👍
@przemekfryc5495 Жыл бұрын
@@LMAutoRepairs they only have some interface and program for 20£ so I don’t think is the one. Too cheap I think 🤔
@mlppiggybank2034 5 жыл бұрын
So if I have the pin code I can do all this with the autel ms908 ? Thanks
@LMAutoRepairs 5 жыл бұрын
Most likely you can! Thank you for watching and for your comment!
@martinguitarhd28 6 жыл бұрын
Hi lmsvvavr, I own op-com .I have a vauxhall vectra c 2006 1.8 z18xer vvt petrol .Will car prog read the pin code on this ? which version is better for success on this and other makes of cars ? Also is there one that works with say win 7 / 8.1 ? Thanks.Excellent tutorials by the way.
@LMAutoRepairs 6 жыл бұрын
martinguitarhd28 Thank you for watching! It should read... Google for ECU compatibility.... hope that helps...
@gurmanlall8247 3 жыл бұрын
Hi i have a 1.4 16v 2004 14xe engine vauxhall corsa c which opcom version do i need for the reprogramming.
@LMAutoRepairs 3 жыл бұрын
Any should do really... but if you are about to buy it, go for the latest... Thank you for watching!
@gurmanlall8247 3 жыл бұрын
Hi i have followed your video step by step with my opcom but when i get to the instrument cluster it doesnt do anything it doesnt program it.
@LMAutoRepairs 3 жыл бұрын
You can always try a different version... I know there is some versions out there that have some bugs...
@seanhawes601 4 жыл бұрын
Can u install a 1.4 ecu in that 1.6 motor
@LMAutoRepairs 4 жыл бұрын
I guess you can... never thought about it... Thank you for watching!
@EliseiDesign 6 жыл бұрын
Hi, Was your replacement ecu serial number the same with the car ecu serial number. Would it work with a different one? Thanks beforehand!
@LMAutoRepairs 6 жыл бұрын
Hi As far as is from a similar car, should work, even if the numbers are different... as sometimes different numbers only mean that the hardware and or software has been revised, but the functions of the ecu remain the same... However, if you can get hold of one with the same numbers, the better.... Hope that helps. Thank you for watching!
@EliseiDesign 6 жыл бұрын
I see. Well ,I believe the replacement was from Meriva and my car is Zafira. The immo sequence went alright and the car started, unfortunatelly there were 3 errors: two with the fan and one with the AC. They were present but not functioning. Ac wasn't functioning and the radiator fan didn't start. Is there any way to reprogram the ecu or it is too complicate ? Thank you very much for replying! The guy who did the immo did not programm the VIN. Could that be the issue?
@LMAutoRepairs 6 жыл бұрын
Have you checked the configurations? If you can configure things in there, then is because that ecu does not have those functions... Check configurations and go from there...
@EliseiDesign 6 жыл бұрын
The AC was present in the configurations, still, didn't work. The guy who did the reprogramming made all the necessary steps and after that he said I should have bought the same serial number ecu because the software is different. We finally opened the faulty ecu which already was repaired 3 times and there was a loose wire. Now he will remove all the wires and weld new ones to make sure it lasts longer not just one month as it did now. Only one side, as the other one seems to be in order and not touched. Thanks again and take care!
@cuneytkaymakci605 Жыл бұрын
I have changed my instrumen panel on my opel corsa c class 2005 i have the security code but its doesent work on body control module when i enter the security code it says wrong security code but when i enter the same security code ecu, and immobilizer its working but body controle modul says wrong security code
@LMAutoRepairs Жыл бұрын
Which tool are you using? 👍👍👍
@cuneytkaymakci605 Жыл бұрын
Opcom 1.99 version
@cuneytkaymakci605 Жыл бұрын
The body control is ok ,but instrumental panel security code not work
@LMAutoRepairs Жыл бұрын
Try a different version... different versions behave differently on different cars... 👍👍👍
@LMAutoRepairs Жыл бұрын
If you replaced the cluster, you need the original pin code from the cluster in order to reset it first, just then it will accept the pin from the car you are trying to install it on... 👍👍👍
@hbenred1384 7 жыл бұрын
thank you so much , great as alwayse
@LMAutoRepairs 7 жыл бұрын
hben red Hi Thanks!
@alialzoabe9381 5 жыл бұрын
Hello I need know how kan I PROGRAMMING Vauxhall/Opel Meriva 1.4. Engine ECU replacement, reset and programming med Carprog. THANK
@LMAutoRepairs 5 жыл бұрын
Car prog alone should be able to do it... But any coding you will need Op-com or other capable tool.... Thank you for watching!
@emmanuelachiume3069 6 жыл бұрын
I really love your videos, I have learnt a lot from them. Just want to know something, what other version of opcom apart from v1.39 will reset the pin on Corsa C instrument cluster? I have tons of them that just bricked on me and I could really used some help on how to bring them back to life. I'm supposed to change the dash on my 2004 Meriva this coming weekend as it's the U.K. type that uses miles to the kilometre type suitable for my country. Thanks.
@LMAutoRepairs 6 жыл бұрын
Emmanuel Achiume Hi Thank you for watching and for your comment! There is another version out there, 1.45... But both versions are able to read the pin on the Corsa c... When you say they bricked on you, do you mean the op-com?
@emmanuelachiume3069 6 жыл бұрын
lmsvvavr I have 2 v1.45, v1.64 and v1.69. None of them will read or reset the pin on Corsa C. Only the 1.39 could do that. I have tons of bricked opcom interfaces which I want to learn how to revive. They are all recognised by the laptop, drivers install but pretty much nothing else. The repair opcom tool doesn't work either. Which software version will work on v1.45 to read pin on Corsa C? Thanks in advance.
@LMAutoRepairs 6 жыл бұрын
Emmanuel Achiume I am pretty sure that v1.45 also reads... If you have opcom tools just load the 1.39 on one of them...
@partoems9376 Жыл бұрын
So with this step-by-step approach, I have been able to program the meriva 2003. The only thing left is the error code in the immo is the security code not programmed and the flashing N on the IPC. Any help LM?
@LMAutoRepairs Жыл бұрын
Have you programmed the ecu using your car's pin code? 👍👍👍
@partoems9376 Жыл бұрын
@@LMAutoRepairs I think i did that.but i would love to get the procedure. Thanks a lot for always responding.
@LMAutoRepairs Жыл бұрын
@@partoems9376 The procedure is done in the immobiliser... log in and add the ecm... using the car pin code... That is providing the ecu is reset/virgin... 👍
@partoems9376 Жыл бұрын
@@LMAutoRepairs I guess immobilizer> program immo function and select ecu installed.
@LMAutoRepairs Жыл бұрын
@@partoems9376 Correct... 👍
@Mambre79 7 жыл бұрын
The engine ecu pin code is the same code that is in the immobilizer dump? Same code for ecu, bcm, instruments, immo or they are different? Nice tutorial.
@LMAutoRepairs 7 жыл бұрын
No, you are correct. All the modules will have the same pin code. Thank you for watching!
@Mambre79 7 жыл бұрын
Do you know how to get pin code from instrument panel eeprom dump? op com can read and change millage on many dashes.
@LMAutoRepairs 7 жыл бұрын
Op-com can indeed read the pin from dash on some older models... ICC can do it.. there is other softwares out there, or info for the bytes location of the pin... google will help you on both....
@gurmanlall8247 3 жыл бұрын
Ok i have bought a complete set engine ecu bcm immobiliser reader transponder chip ignition barrel boot lock door lock ignition key and dash cluster plugged it all in the immobiler light is out have erased all the faults using opcom still did not start there was no ground feed to the fuel pump relay. I intoduced a ground feed and the fuel pump run and the car starts but the vin no is incorrect as whole set from other vehicle now it not reading the ac automatic transmission etc. What do u suggest i do do i still go and reset the ecu and follow your video or follow your video and program the can configuration and variant can please help me as i not sure what to do many thanks.
@LMAutoRepairs 3 жыл бұрын
Program car configuration etc...
@gurmanlall8247 3 жыл бұрын
Still no need to reset ecu just do the can configuration etc.
@LMAutoRepairs 3 жыл бұрын
I think you are confused about the reset procedure... The reset it is just to allow the module to be programmed using a different pin... like into a different car... The reset does not touch the flash inside the modules...
@gurmanlall8247 3 жыл бұрын
Is it possible to send your contact no so i can discuss the full matter with you many thanks.
@LMAutoRepairs 3 жыл бұрын
Try the forum... Myself or someone will help you... prodiag.boards.net/
@alien-bl6yd 4 жыл бұрын
Great work thanks .
@LMAutoRepairs 4 жыл бұрын
Thanks! 👍👍👍
@armandonika 7 жыл бұрын
I sork on an opel dealer, poor diagnostic info on their website where do you get the info about various systems? Thanks
@LMAutoRepairs 7 жыл бұрын
armando nika All over really... Google is very helpful... Autodata and similar... The rest is learning.... Thank you for watching!
@GarysTechSupport 4 жыл бұрын
Hi Great video dude, can you set the mileage to the original value or is that stored in the instrument cluster ? As that will flag on my next MOT
@LMAutoRepairs 4 жыл бұрын
Hi That's in the cluster... this does not disrupt the mileage... Thank you for watching and for your comment!
@GarysTechSupport 4 жыл бұрын
LM Auto Repairs Thanks for the reply, I hope it doesn’t come to that. I changed a head gasket and timing chain on a Corsa D 1.2 56 plate. Now I’ve got p0036, p0141 & p0304 sensor 2 and misfire pot 4. I’ve got compression and fuel just no spark. Taking (left pin coil pack from gearbox view) 1- 0v 2-12v. 3-6 pots 1-4 going pin 1-6 I don’t get same reading as 1-3,4,5 so if these are correct pin outs it could be coil pack but seem too much of a coincidence to me... all plugs are in and engine does run with misfire, I thought I was gentle with the cables too, ordered op-com should arrive by Friday. Love to hear your thoughts 👍
@LMAutoRepairs 4 жыл бұрын
@@GarysTechSupport Just check, double check, and triple check everything... it is easy to sometimes miss things... get some diagrams... it is a bit confusing the way you explain the pin out... Then check primary ignition signal... if is there, and you have no secondary ingnition, then is your coil pack... Hope that helps
@ntsikayethusibeko1520 3 жыл бұрын
hello, I'm trying to retrieve the passcode from the ecu 9:52 I have the followed the same steps but I always have a problem its says "wrong passcode" , no synchronization data comes up. Can you help me resolve this issue.
@LMAutoRepairs 3 жыл бұрын
Are we talking about the same ecu? Thank you for watching!
@ntsikayethusibeko1520 3 жыл бұрын
@@LMAutoRepairs Yes its the same ECU
@ntsikayethusibeko1520 3 жыл бұрын
@@LMAutoRepairs Can you advice me on how I can fix this issue, do you know how i can get the correct passcode, to complete the reading.
@LMAutoRepairs 3 жыл бұрын
To read the pin with car prog, you don't need any pin... Just select the correct ecu and retrieve the pin... You will need the pin to then reset it and program it again... As per the video...
@williamgall9616 5 жыл бұрын
Hi there I was wondering where do I get the software from and the cable to to connect to the car and also will this work the exact same way for a zafira MK1 2004 model. Reason I'm asking is I have had the lamba sensor replaced but the engine management light stays on even though the error codes have been reset, the cables have been tested and seam to be ok so the next thing is the ECM that needs reset or replaced which looks simple by your video. I hope you can help or advise. Thanks
@LMAutoRepairs 5 жыл бұрын
The lambda codes can be a result of something else... well you don't say the codes... so just thinking out loud here... You can get Op-com on eBay... software comes with it... Thank you for watching and for your comment!
@williamgall9616 5 жыл бұрын
@@LMAutoRepairs yeah I meant the lamba codes have been reset and nothing else comes up. The sensor has been replaced 3 times with the same issue and codes come back on once the engine has been switched back on. What else could be the issue from your experience? I have heard it could be the ECM that's been tripped and needs replacing and can cost a arm and a leg to get someone to do it.
@LMAutoRepairs 5 жыл бұрын
@@williamgall9616 It is possible that is the ecu... if they are definitely hard codes, and everything else has been checked...
@martinhofranca8777 3 жыл бұрын
Hey there I have same car same problem I’m just wondering if with carprog will be the same or even easier to program this ecu thanks
@LMAutoRepairs 3 жыл бұрын
Same principle yes.. 👍👍👍
@martinhofranca8777 3 жыл бұрын
And when u don’t have comunicacion what do u do coz I don’t have any comunicacion on both ecu thanks
@LMAutoRepairs 3 жыл бұрын
With carprog?
@martinhofranca8777 3 жыл бұрын
Yes even with the old ecu I don’t get comunicacion
@LMAutoRepairs 3 жыл бұрын
Is the ecu listed in carprog? Make sure you do the correct selection... Have you tried other tool, like Op-com?
@babyninjaonboard6191 6 жыл бұрын
Thank you very much for the vid it hepls Can i ask you a favour can you please find out if the carprog can read the pin code for astra h 1.8i auto 2005 z18xe.
@LMAutoRepairs 6 жыл бұрын
Baby Ninja On Board Hi Thank you for watching and for your comment... I will have a look when I am off work...
@babyninjaonboard6191 6 жыл бұрын
Thank you will be waiting
@LMAutoRepairs 6 жыл бұрын
Baby Ninja On Board Hi On the CAN it does: Siemens Simtec 71.5 Siemens Simtec 71.6 Siemens Simtec 75 Siemens Simtec 81 I am pretty sure being a 2008 is full CAN... I am not really sure which one is on the Z18XE, but I would guess is one of the above... Hope that helps....
@siralexu 6 жыл бұрын
will the car need reprograming if i swap the read coil and key cip with the ecu ?
@LMAutoRepairs 6 жыл бұрын
alex cristian Hi Yes it needs... you still have the cluster and bcm originally installed...
@siralexu 6 жыл бұрын
Damn i thought if i just swapped the imobilizer read coil the transponder key with the engine ecuon my astra g it would have worked because i keep seeing people on ebay selling kits comprised of these parts
@LMAutoRepairs 6 жыл бұрын
alex cristian It will work, but only after the programming of those parts into the original car immobilizer system... a bit like on the video...
@marinosimion 3 жыл бұрын
Evening LM. Thanks for those video. Silly question: Do I need to by a special plug-in connector to be able to use/read information on Carprog? thanks!! M
@LMAutoRepairs 3 жыл бұрын
Hi What kind of information? Thank you for watching!
@marinosimion 3 жыл бұрын
@@LMAutoRepairs HI! I need to rescue the PIN numbers from both of my Astra G (2001) & Astra H (2009). I have the OPcom tool but it is too new and the PIN code option is not there anymore. Any suggestion? thanks! M
@LMAutoRepairs 3 жыл бұрын
kzfaq.info/get/bejne/gpOHhruT2c64cqc.html
@krimokrimo655 3 жыл бұрын
Hi would this work on Meriva 2008 1.3 CDTI as it’s got different ECU . Part number 55566400HQ? Thanks
@LMAutoRepairs 3 жыл бұрын
Yes... The procedure is very similar... I think I have videos on it... if no I have them to be published.. 👍👍👍
@krimokrimo655 3 жыл бұрын
@@LMAutoRepairs thank you mate 👍🏻👍🏻👍🏻
@krimokrimo655 3 жыл бұрын
@@LMAutoRepairs i have followed the steps but when connecting opcom to the car couldn’t access the car ecu . There is a message saying : initialling ecu and after saying : could not access ecu . Does it mean that the ecu is dammed inside or something wrong with ecu connexions ? Thank you for any advice
@LMAutoRepairs 3 жыл бұрын
One of the two... yes...
@lollershit 6 жыл бұрын
Wich tool are you using? what cable for carprog are you using?
@LMAutoRepairs 6 жыл бұрын
Hi The cable for carprog? I am confused... Thank you for watching!
@lollershit 6 жыл бұрын
What are you connecting the car with while using carprog to retrieve pin code? And one more thing. Wich partnumber should match the old ecu? is the number in top right corner of the sticker?
@LMAutoRepairs 6 жыл бұрын
@@lollershit Hi Carprog has its own interface... The part number is that one, yes....
@123tawas 5 жыл бұрын
Thank you well done
@LMAutoRepairs 5 жыл бұрын
Hi Thank you for watching and for your comment!
@gurmanlall8247 3 жыл бұрын
Hi what is a programmer is it similar to carprog.
@LMAutoRepairs 3 жыл бұрын
What exactly are you trying to do?
@Darla-yb4nf 5 жыл бұрын
My dads Zafira is playing up right now. Some days it’s starts up perfect other days it’s a bugger to start (won’t turn over) but starts eventually. After driving for a bit it loses speed and cuts out plus It hardly makes it up the hills, sometimes it won’t make it up the hill. Tonight they was driving home (about 10 miles drive) and the car just completely stopped and wouldn’t start at all so they call recovery. Anyone know what it could be? The car is a Vauxhall Zafira 2003 1.8 automatic
@LMAutoRepairs 5 жыл бұрын
Hi That can be caused by many different root causes... Anything I would suggest, would be pure guessing... So, my suggestion is, start by have it scanned, and a good live data analysis... Hope that helps. Thank you for watching!
@robthomas7232 7 жыл бұрын
Hi lmsvvavr thanks for your videos they are invaluable in helping me fix a 2004 1.4 Corsa with a Z14XE engine. I bought a reset ECU with the same part no as the original (12237450 DXKB) from ebay. When following your instructions opcom connected to the ecu and stated it was a 12245500 FAHX for a Z16SE engine and that it had been reflashed previously. Do you know how to get it back to a 12237450 DXKB for the Z14XE with opcom or other tool? Also as it programmed to the car ok is there any risk in starting the engine with it thinking its a Z16SE?
@LMAutoRepairs 7 жыл бұрын
Rob Thomas Hi Thank you for watching and for your comment! That's weird.... to flash it back you need other type of tools... not opcom... Do not know even if the engine will start... as some wires might connect to different pins on the ecu... also the mix air/fuel wouldn't be correct...don't really know... I never tried... I would send it back and get the right one... Sorry if I can't be more helpful this time...
@robthomas7232 7 жыл бұрын
Hi, thanks for the prompt response and its along the lines I was expecting. From the reading around forums I believe the ecu hardware is common to some engines, z14xe, z16xe and z16se. However the software flashed to it to support a specific engine is different and some are saying that the part number on the sticker can be different to whats flashed. In my case the stickers on the original one on the car matches what opcom reports and is what I purchased from ebay (they are quite rare). I think it has clearly been changed to the z16se version as opcom reports the repair shop and programming date have been set. Some are saying that tech2 can reflash this back to the version that will support the z14xe. Unfortunately I don't have access to that in Swansea, not sure who does and what it will cost (trying to do this on the cheap). I think my only option is to return it as I don't think the ebay seller realised this as it was advertised for the corsa which I don't think had a 1.6 engine? Also since I bought this I missed an entire set of ecu, immo ring, cluster, immo chip, auto cu which stated it was off a 1.4 Corsa auto and £20 cheaper than what I paid just for the ecu ... grrr! There is a 2 year story behind this but I think it proves that not many garages (been to at least 3!) are able to diag and fix these sorts of issues. So finding a skilled auto electrician, electronics repair expert and computer specialist like yourself is essential and very difficult! Thanks once again.
@robthomas7232 7 жыл бұрын
OK took the gamble and tried to start it. It didn't want to start but you could hear it trying to catch and eventually did with a bit of accelerator pedal but then cut out when the pedal was released. An unidentified error came up which I'll post the code to later (on a different laptop). The code and cutting out maybe down to the wrong engine type being on the ecu .... or a hardware issue with the ecu or something else. I would have been surprised if the right ecu would have fixed everything. I guess the good news is though that as I'd removed the fuel pump relay link (bodge) the engine clearly got fuel which means the fuel pump relay was activated and the pump working. This was one of the things pointing at a failing ECU amongst other things. So I will chase the ebayer later although not sure how much more effort I'm going to put into this as the timing for further fix attempts is limited and its causing family issues now ;-)
@madmatt1964ify 5 жыл бұрын
how do I find my security code for my vehicle? Zafira B 2008.
@LMAutoRepairs 5 жыл бұрын
Hi kzfaq.info/get/bejne/gpOHhruT2c64cqc.html Hope that helps... Thank you for watching!
@sheledmikymo 5 жыл бұрын
does a clone carprog have the same functions to read tigra b ecu code? or does it need to be a full genuine copy, great videos by the way,
@LMAutoRepairs 5 жыл бұрын
Hi If the car is fitted with one of supported ECUs, should work... Thank you for watching!
@jeanpybolakisa5614 6 жыл бұрын
HI my car is now ecu fault cutting out and or not starting vauxhall meriva semi automatic year 2005
@partoems9376 Жыл бұрын
Hi thanks for the video. Can im608 do this ecu replacement on meriva 2003?
@LMAutoRepairs Жыл бұрын
I believe it can... 👍👍👍
@partoems9376 Жыл бұрын
@@LMAutoRepairs Thanks for the response. I used the IM608 to track all the menus as whiles following the video. All the menus are there. Except BCM reset. Program variant config and CAN config is under Diagnostic > select vehicle > service>powertrain>adaptations. Is there a way to reset the bcm on im608? Thanks a lot for the video once again.
@LMAutoRepairs Жыл бұрын
@@partoems9376 Most likely will be, but I never used it for that, even the MS908P I struggled in the past, and just ended up using Op-com... But I am pretty surely will be there somewhere... Just one thing, carefully reseting the BCM... The BCM does rarely needs reseting... adding a replacement ecm does not require a BCM reset...if I recall correctly... 👍👍👍
@partoems9376 Жыл бұрын
@@LMAutoRepairs IM608 is able to reset ecu and write the VIN successfully. Now i have dtc wrong vehicle id from instrument & body control module. I think that's where the bcm and IC reset is required.
@LMAutoRepairs Жыл бұрын
IC... do the IC first... I don't think you need to do the BCM...
@MrRadu1983 7 жыл бұрын
Hello! If i change on an Astra G 1.7 DTI the ECM+imobiliser+key cip, do i need the CAR PASS ( PIN) of this ECM ? Thx!
@LMAutoRepairs 7 жыл бұрын
THE STIG If you get all the immobiliser parts, providing they all come from the same car, no pin is needed...
@MrRadu1983 7 жыл бұрын
Or i get an reset ECM in that case i need only actualy PIN of ECM that is instaled on my car (i have it on car pass card). U know if i can program it with Delphi ds 150E or i need Op Com? thx!
@LMAutoRepairs 7 жыл бұрын
THE STIG Correct! An reset ecu is ready to accept any code... so if you have the car pass you have all you need... I never really worked with delphi... so don't really know if capable of that...
@MrRadu1983 7 жыл бұрын
Tank you very much! U do a nice work!
@LMAutoRepairs 7 жыл бұрын
THE STIG No worries... here to help... Thank you for your comment!
@louisstellini7711 5 жыл бұрын
CAN YOU SHOW ME THE ECU NUMBER ON BODY. THANK YOU.
@electronics1267 7 жыл бұрын
Thank you.
@LMAutoRepairs 7 жыл бұрын
electronic eng You're welcome !
@Neevoks 11 ай бұрын
How do you get the PIN from the dash?
@LMAutoRepairs 11 ай бұрын
With certains tools... Op-com can do some, and other tools can also do it... It all depends on the model... 👍👍👍
@Neevoks 11 ай бұрын
@@LMAutoRepairs I have Op-com, the car is a Meriva A OPC
@LMAutoRepairs 11 ай бұрын
Not sure Op-com can read the pin on that one... depends on the ecu as well... You might need other tools... Is the security card been lost?
@Neevoks 11 ай бұрын
I wouldn't even know where to look for the security card @@LMAutoRepairs
@LMAutoRepairs 11 ай бұрын
@@Neevoks I sometimes find it in the car folder or paperwork... Unless has been lost...
@Chizzy_Man 7 жыл бұрын
OFF TOPIC: Imsvavr, what do you use to read Motorola MCU like the one Jaguar 2001 dashboard 68hc11ks8?
@LMAutoRepairs 7 жыл бұрын
redman I don't know if I have ever read that one... nevertheless x-prog might be able to do it...search for the compatibility table... Otherwise (if I had to read that mcu, would be another toll for me to buy... lol Hope that helps...
@Chizzy_Man 7 жыл бұрын
ok cool, been reading about the UUPA programmer that it can but wanted feedback first on any other better tools, coz i need to program AKL all keys lost for Jaguar S-type 2001 and obd is failing
@LMAutoRepairs 7 жыл бұрын
redman I can't comment on UPA... I do not have that tool... perhaps other people who have it can do it...
@Chizzy_Man 7 жыл бұрын
thanks man, great video by the way
LM Auto Repairs
Рет қаралды 177 М.
LM Auto Repairs
Рет қаралды 209 М.
LM Auto Repairs
Рет қаралды 173 М.
LM Auto Repairs
Рет қаралды 39 М.
LM Auto Repairs
Рет қаралды 169 М.
Madman Car
Рет қаралды 317 М.