Really good watch Dado. Inspiring me to VESC my Pint in the future. I always enjoy watching squirrelly setups. Makes it look like you're putting in work. Also, all your "oh shit" commentary is hilarious!

Great work the pint is twitchy off-road , its good to see just what is possible for our One wheels in the future.

Nice commentary and variety of shots! Your best vid to date 🤟🏻 And you'll love that Enduro pint tire, so stable yet carvy! Oh and that's dope u can have it go into stand mode after riding, would be fun when you run into a store real quick and leave it at front 🤣

Honestly this was great video! One of your best I found it the most entertaining

Your a great pioneer in this stuff, you're rambling on about things is how we're going to learn. Music was a bit much in the beginning

You're amazing bro! 🤯🤯🤯 Future is bright!

I got mine done today. Thanks much for your help though this video!!!

"the stock pint tire makes it challenging" haha that's the fun of it!

Oh hell, flywheel mode! Thats so cool!

I can’t wait to see mods done like this but the the Onewheel GT with all of its factory lock outs!!

Normally closed 12mm switches are quite common, but not with LED light. However, since you can program an automatic power down after x minutes, the switch is only needed for the wakeup functionality and a light is not really required.

Flywheel mode so damn cool 😎

Another great tribute to the community. Can this bms mod work for the lil focer 3.1 and then a 4209 BMS

I had a 60v trampa Vesc 6. I liked it! Fit good in the pint housings. Not having Pull down resistors was a pain. But I think with my current engagement system I might not even need pull down resistors.

The pulldown should be placed as close as possible to the JST pin on the VESC controller. Reason: when the cable brakes it should pull down the signal to GND. We can design a little pull down pcb with ease.

Wow that's amazing bro...did you ever have time for update on this project and will you sell your diy boards?

We discovered today at work at Trampa that the vesc 6 fits the stock controller case bolted to the lid. Happy days

So is the lil focer or the trampa the best bet for pint assembly and vesc tool compatible

I have been waiting for work (trampa) to get the 6 75 in stock for my first vesc swap. Can I ask what pull down resistor values you used? Did you find a suitable momentary switch for this vesc? Is there anything new or not in the video you can add, since the time of making this video? Thanks always for your work to help the community, we appreciate you

Amazing work! And what about the speed? Would be interesting to see what happenes at the usual pushback speed. I am really close to vesc my Pint X as well.

Love this! Thanks for all the infotainment you have put out. Can I ask if a stock controller case mod is possible to fit a trampa vesc? To start I will use stock battery / bms, and soon a UK cbxr clone instead. Any particular trampa vesc you can recommend please? And anything additional I may need. If you wouldn't mind. I started work at Trampa recently so hoping to connect with a couple of faces who they know and see what's up

What is the pole count in the pint motor?

@surfdado will you be releasing a document with a setup guide like you made for the XR conversion going over wiring, soldering and jst connectors as far as wiring the VESC to as much stock components as possible? I think the community would be very grateful for it.

Whisper wide is great on the PintX, and only weighs 1.0kg

is it true the red wire on the bms and battery is negatively charged?

Will a powerbutton be possible sometime in the future?

⚡⚡⚡

I noticed your battery's negative lead looks like it has something on it, did you have to reinforce it?

what is this magic at the end!?!?

I have 2 broken pint x could you build or help me build them? Thanks!

What’s the top speed you can get?

if you increased the battery size to 16s as just stated was possible in the beginning of the video, how would that increase the range? and the torque?? obsessed with my pintx just wish it has a little more range. if it could go 25 miles and had XR style pushback, I would never need to buy another wheel ever again.

👍🏾🙏🏾

As part of this transition from FM based OW to VESC based OW think about, at some point, adding a feature to bleed off charge during full charge downhill runs.

You don't need to replace the button. You just need to use binary logic to invert the value. There are lots of ways to do this. I have ideas, but they are probably outdated. If you can't find a younger EE to propose a circuit for you, I'll tell you how I would do it. Let me know what you think. ☮️❤️🌈

Any chance your app will come to Android?

Yeah the stock tire is squirrelly but I needed it squirrlier lol

2:21 Who keeps the envelop that their TFL float plate comes in? Oh wait ... there's one to my right.

its so hard to watch anyone record while riding..esp when they as squirrely as this dude- last month I had my first nose dive ever after 200 miles without ever doing so... ate the pavement @ 13mph..the only protective gear I was wearing was gloves and pants only because it was night and a little chilly, the pants didn't do much both my knees got ate up, luckily the gloves saved my hands which i can only imagine what they would have look like had i not wore them.., gashed my eyebrow had to stitch it up 5times and my chin right/front side got rashed pretty bad...got it on camera tho - which after you watch me eat it all you see is trees and sky going by as you hear the fading sounds of me moaning and swearing for a good 4-5 secs awhile my phone flew/slid a good 25-30yds down the street... I watched it once and refuse to watch it again. Im designing/testing my own device to put on the front to prevent it from happening again. yes i know these exist but i think I can do better and make one much more compact. I like my pint but wish id bought a GT my feet are too bigand I have to have them placed in one exact spot or im not comfortable on it