Vespa ET4 OIL CHANGE 125cc

Рет қаралды 37,948

4 жыл бұрын

MAKE YOUR DIY OIL PAN : • DIY (GOLD PLATED ) Oil...
Vespa Oil Change
I used 10W-40 Mobil oil and a filter from parts unlimited ordered from ebay
(part no.410229).i recommend to change oil in every 2000 KM for a longer maintenance free engine.Change your oil filter in every 4000 KM.
NOTICE:-
"You need 1L of Engine oil.AFTER you fill up the oil until you reach the maximum level as marked in the oil level glass,close the oil cap and check the oil level glass.Then start your engine
let it warm up for 3 minutes and don't rev it.after that you can have a test run.you can feel how smooth the engine runs.the day after the oil was changed and you can check the oil level,if oil level is below the maximum level you can fill it up until you reach the maximum level.then you good to go to hell as well."
Questions are welcome in the comment section......
Thank you....
Don't forget subscribe !!!
LIKE US ON FACEBOOK "Vespa elegante"

Пікірлер: 38

@wupper_duke3460 4 жыл бұрын

Very nice👍

@EnphasyPossiedo 3 жыл бұрын

Please make a video where you show me how i can change the candel . Tank you

@xodrinker 4 жыл бұрын

Good video, thx.

@junktv1962 4 жыл бұрын

welcome xodrinker..

@MG-go6kv 4 жыл бұрын

very nice your video. can you also show how to change the candle?

@junktv1962 4 жыл бұрын

Hello emme, I will upload a video about that emme.

@shayamapriyanthi8395 Жыл бұрын

Very Good

@ERNESTOSKIMVLOG Жыл бұрын

Super nice video! Just wondering. Did you use the entire bottle of 1L oil? Or just half of it? Just to know if I need to pour the entire 1L oil. Thanks!

@ERNESTOSKIMVLOG Жыл бұрын

And how many kms could I do once I've changed the oil till the next oil change? Thanks!

@TheJimmys1999 4 жыл бұрын

Great video!I have a et4 125 "1999".Do i follow the same steps as in your videos?

@shenarkwickramasinghe2356 4 жыл бұрын

Yes if you follow you will not harm your vespa !!

@junktv1962 4 жыл бұрын

Hello mitsos, Thank you for the feedback.if you can follow the steps it will keep your scooter away from damage. Atleast use OEM products.

@Gustynios 4 жыл бұрын

Hey - is the seal glue necessary when I have a new o ring for the Oilfilter change ?

@junktv1962 4 жыл бұрын

Hello patrick, you don't need to use a seal glue if you have a new one. #patrickgustyn .Thanks for the feedback.

@kennethmccullough538 4 жыл бұрын

Absolutely not

@rohandebisarun7509 3 жыл бұрын

Where do you need te fill the oil on a piaggio sfera 125cc 4stroke i don’t have a dipstick

@SAM-zt2uy 2 жыл бұрын

3:30 shows you the sight glass, there will be marks on that to show you correct oil level

@kitz8127 4 жыл бұрын

there's another screen filter on the other side that you didn't cleaned!

@junktv1962 4 жыл бұрын

Hello lim, Thank you lim for the feedback. can you take a screenshot and E-mail to Shenarkw@gmail.com .

@kitz8127 4 жыл бұрын

@@junktv1962 I've sent you the pictures.... near exhaust pipe.... under stator flywheel fan.

@CRinierabarbershop Жыл бұрын

Where can i buy it? On Amazon? Do you have a link?

@junktv1962 Жыл бұрын

What Do you mean brother?. OIL FILTER?

@ayokunanomibailey5987 3 жыл бұрын

Bro plz how can I get intouch directly to you thanks

@junktv1962 3 жыл бұрын

Shenarkc@gmail.com Email

@springerXXX Жыл бұрын

How much oil do you need to pour?

@shenarkwickramasinghe2356 Жыл бұрын

1L can is enough..

@jamesmacdonald3090 4 жыл бұрын

A very simplistic oil change, gasket sealant is the stuff to use if you don't have an O ring, not glue and certainly not all over the housing and inside! You forgot about warming the engine, removing the oil filler cap to stop fluid vacuum, cleaning screen near exhaust, checking level after short run, these engines should take a litre of oil but you gave a half measure for some reason? Basic stuff really! I wish people wouldn't do these "DIY" vids when they don't know what they are doing... should have a disclaimer!

@mathews-e5418 4 жыл бұрын

all these points are great, James. any chance of some links to a video showing a more thorough walkthrough?

@junktv1962 4 жыл бұрын

hello james, yes,i haven't mention the checking the oil level and engine warm up. i will mention that in the description. Removing the oil filter cap and cleaning screen near exhaust.i don't get it. i have used the whole oil bottle of oil (1L).yes i didn't mention it too.i will mention that in the description too, Talking about DIY if you do DIY you save money.even you do DIY'S in your life bro. I see DIY AS a good platform to increase your knowledge and experience.but the thing is you have to do it right.''EFFECTIVENESS"=doing things right as "Peter Drucker" said. I have been doing this for years now.so i know what i do but i accept i haven't mention some important things. so thank you James Macdonald for your great feedback.

@jamesmacdonald3090 4 жыл бұрын

Should be fully synthetic oil on these motors.

@jamesmacdonald3090 4 жыл бұрын

@@mathews-e5418 Its basic stuff, the oil strainer is on right hand side behind near stand mount and exhaust pipe, you will need to lift floor board for tight access and have oil drained... there is a plastic mesh tubr which can be wiggled out, clean off with parts cleaner, check for holes and debris before refitting.

@junktv1962 4 жыл бұрын

@@jamesmacdonald3090 I have mentioned it correctly brother.