vespa FAIL: brake & clutch LEVER by pm-tuning MOUNTING / FMPguides

vespa FAIL: brake & clutch LEVER by pm-tuning MOUNTING / FMPguides - Solid PASSion /

Рет қаралды 7,337

FREAKMOPED Vespa Tuning | FMP - SolidPaSSion |

5 жыл бұрын

do NOT! buy them. complete FAIL design.
• vespa CNC lever FAIL, ... extremly annyoing, even the clutch doesnt work anymore. I git rid of them after 2km.
cnc machined, cool looking levers for both sides. practical? worth it? lets see...
HIGHLY NOT RECOMMENDED. second guide 2come! as a motorbiker you are totally annoyed after only 50m. its a total FAIL design, done by someone who doesnt care at all and has no idea. how can you provide & sell such unusefull hardware? its unbelievable.
the issues:
1) the clutch doesnt work anymore cause the lever stroke is wrong! no matter how you set the cable (lever position doesnt change clutch cable itself) it does not work
2) they are too long!
when your fingers are at the lever edge where they are supposed to be designwise, your hand is 5cm outside of the handle (WTF!)
3) if you drive and dont have your fingers on the brake lever
so you just turn the throttle, YOU SQUEEZE YOUR FINGERS!! (if you are a grown man) omg
the solution:
1) simply dont buy it.
2) get rid of it when you have it! only super annoying
3) &drink a beer to calm down :D
--------------------------------------------------------------------------
FOLLOW me on
insta: @FreakMoPed
fb: / freakmoped
--------------------------------------------------------------------------
like what u see? found good tips?
u can support FMP via PATREON:
/ freakmoped
_
DISCLAIMER: the information shown in this video, is about THIS specific hardware. it is my personal observation documented with this video. It DOESNT automatically mean, that all such parts by this producer or seller do have or will have same issues.
_

Пікірлер: 19

@michaelchum 2 жыл бұрын

I really like the PM tune levers. I have no issues at all. It's effortless on the clutch side and I use more front brakes than before. The front brake is a lot of bites compared to the original lever.

@FreakMoPed8 2 жыл бұрын

do u motorbike additionally to vespa

@paulrobinson7881 3 жыл бұрын

great video now in will order my pair

@FreakMoPed8 3 жыл бұрын

do NOT order them, they are completelly useless. Super annoying from the very first meter on. After few km the were removed.

@paulrobinson7881 3 жыл бұрын

@@FreakMoPed8 I'll look for better ones thanks buddy

@dayla8634 5 жыл бұрын

I just installed a set on mine. I'm having some issues on the clutch side. It feels that there is not enough travel when the clutch is disengaged. It creeps forward a little. I was wondering if you have any issues like this?

@FreakMoPed8 5 жыл бұрын

these levers are complete bullsh... just get rid of them. Yes. Clutch doesnt work anymore. Caused by fancy cnc levers....

@dayla8634 5 жыл бұрын

@@FreakMoPed8 These have been out for a while now. I'm surprised that they are still on the market if people are having problems with them or that it's more known.

@FreakMoPed8 5 жыл бұрын

why are very bad stoneage tyres still sold and people are happy with it? :) and esp with vespa a LOT is about fancy looking, isnt it :D they are totally crap. after 50m you are already SUPER annoyed. (as a motorbiker!)

@Rene71Nrg 5 жыл бұрын

Hatte riesen Probleme damit. Bremse ging immer fest. Hatte total übersehen in der Beschreibung, dass die nur mit Grimeca Bremszylinder passen und nicht mit den neueren von HengTong 🙈

@FreakMoPed8 5 жыл бұрын

Oweeeh, das ist ungut ^^

@nitrocraft 5 жыл бұрын

Seit dem ich die PM Hebel dran habe, trennt meine Kupplung nicht mehr vollständig weil der Knick der Hebel schon früh am Griff anstehen. Seil ist schon so stark gespannt das der Kickstarter gerade so greift. Hast Du eine Idee wie man das lösen kann?

@FreakMoPed8 5 жыл бұрын

dann stimmt aber das kupplungsspiel auch nicht, das klingt nach kupplungs trouble. nimm die mal raus. wenn zb die laschen angefressen sind trennt das immer weniger, daher spannt man immer mehr nach, druckpilz liegt immer an und bricht dann irgendwann. das sind die schön verfärbten andruckplatten.

@nitrocraft 5 жыл бұрын

@@FreakMoPed8 könntest Du das genauer erklären? Welche Laschen meinst Du und wie wird das Kupplungsspiel eingestellt? Danke an der Stelle für die vielen guten Videos. Habe schon sehr viel dabei gelernt.

@FreakMoPed8 5 жыл бұрын

Nun auch gefahren damit. Die hebel aind beidseitig vollkommen unbrauchbar. Ja, kupplung funktioniert nur noch lala wg nicht ausreichendem. Hebelweg. Ausbauen und wegschmeissen die dinger. Das wirds jedenfalls hier.

@nitrocraft 5 жыл бұрын

@@FreakMoPed8 Vielen Dank für Deine Antwort. Ich dachte schon ich bin komplett unfähig. Habe mehrfach versucht das alles richtig einzustellen. Sogar andere Kupplungen ausprobiert usw. Sehen schön aus aber funktionieren nicht gescheit. Danke für die vielen guten Videos!

@FreakMoPed8 5 жыл бұрын

bidde gerne. komplettes design FAIL, wenn man dort greift wo es gedacht ist, ist die hand halb ausserhalb des griffs. ganz üble teile. kommt eh gleich a video wo man auch sieht dass kulu nur halbwegs auf MAX stellung funktioniert, keineswegs aber auf MIN einstellung.