Step Bye Step - I will talk you threw how to set up your VFD Controller . Very easy - just follow along , run your VFD at it's max RPM and Max Frequency
Пікірлер: 30
@mikeyjohnson95966 ай бұрын
Thank you! Thank you! Thank you! I bought a sensor upgrade package for a dynamic balance machine that was a "some assembly required" retrofit kit. The whole process has been a head scratcher for me but this was my biggest hangup and I really appreciate the solid, simple explanation.
@earthssecretenergy23716 ай бұрын
Thank you i- glad to help, and yes they make it so hard to under stand that's why i made the video for all . all the best i have more vid's on my channel
@mikeyjohnson95966 ай бұрын
@earthssecretenergy2371 Subscribing now my friend. Thanks for what you do!
@romeromelo36014 ай бұрын
Tem como ligar os inversores em paralelo fazendo eles trabalharem simultâneamente
@sarkistatuljan29505 ай бұрын
Question - is it possible to set up the VFD Controller XSY-AT1 so that when turned on it works at high speed, about 2-3 minutes, but after 2-3 minutes of operation to a pre-set low speed? A pool water pump is connected to the XSY-AT1 frequency converter.
@earthssecretenergy23715 ай бұрын
thank you for checking put my video ,hope it helped you out. For your question i believe you can setup 2 settings but you would have to change them manually for what you are asking for. hope this helped.
@mich65282 жыл бұрын
hi, finally what are the parameters you consider very important for the succes? thanks
@bigirish488611 ай бұрын
do you give seasick pills with your videos, MAN PUT THE CAMERA ON A STAND!!
@AndreAndPetya2 жыл бұрын
I'm new to your channel im binge watching all videos from old to new. Do you plug directly the inverter to the wall, to power all the house loads? Or if not, what is it? I found out problems doing that, it seems the inverter does not like when the house wall is grounded. I check the only youtuber that explains, from DC baterries -> to inverter -> to wall, to make it work, we need to shut down the power line, and than to remove the ground wire, and we are good to go. That's why im curious what have you done. Maybe with cold radiation, there is no such problems.. Are you producing cold radiation? Meaning there is no heat coming out of your appliances.
@UTIGERFOOTBALL Жыл бұрын
How do you enable TA TB AND TC RELAY
@rdu3941 Жыл бұрын
I will use 110 volts input is P00 for input.and which code is for output.
@rdu3941 Жыл бұрын
is P00 input or output setup
@saleemkhan-mx9jw4 ай бұрын
Please share deep parameters details of this vfd.
@maximojavi24332 жыл бұрын
If your drive has rs port -485, have you been able to configure it to work with the modbus rtu protocol? and if so, what parameters are used? a greeting
@kiowablue2862 Жыл бұрын
Unfortunately, the AT1 doesn't have an RS-485 port. The user guide says parameters P15, P16 and P17 (parity, baud rate and device address, respectively) are invalid.
@runbou3485 Жыл бұрын
អរគុណThank👏
@user-nu6he3vr7j Жыл бұрын
Can you show me how to reset parameters to factory settings?
@roonney29597 ай бұрын
P77 to 54321 and save
@apsert2 жыл бұрын
@ Earths Secret Energy: I am new to your channel. Soon to be part of the furniture. I have a "Q" - IIf i take a 230 - 240v Speed controller, join this to a washing machine motor, then mechanically attach the Washing machine motor to a Alternator generator like yours. Does this sound correct before i purchase parts?
@earthssecretenergy23712 жыл бұрын
this is correct check out my new video on my page (( is over unity fake ))
@apsert2 жыл бұрын
@@earthssecretenergy2371 Thank you. what do you know i am on your channel and have been since i tuned in. lots of other tab bars up top of screen, but am transfixed right now lol. Great Channel right here !
@earthssecretenergy23712 жыл бұрын
Thank you , yes it is something else when you believe the possible is in possible .
@earthssecretenergy23712 жыл бұрын
Rember this VFD is only ment to run a motor !!!!.
@earthssecretenergy23712 жыл бұрын
The VFD is only intended to run the motor that's all. What you see is more !!
@josetavares7789 Жыл бұрын
mrpt222 he is the man for that sorry.
@user-lb8ze9vq1v Жыл бұрын
What mean error 20
@earthssecretenergy2371 Жыл бұрын
i belive you are running the machine to slow , try starting the moter at a higher RPM should start .. good luck