Aaahhh, I over looked that. Well at least I got some practice at soldering small components. I’m gonna try that if I ever have to install another Voultar board on an 03. Also, I’ll have to familiarize myself with the dejitter mod.

I share your pain. 😅

Thanks. I’m about to upload another one right at this moment, it’s processing. I have a Ksger T12 style soldering iron my favorite tip is Hakko T12 KU it’s the smaller version of the K knife edge style tip. My other iron is a 2 in 1 hot air rework station but, the tip and heating element broke I’ve since replaced it. I may buy a better iron handle with the same Pinout to use on the 2 in 1 station.

An old Polaroid tv.

The serial number started with UN32 usually those were the last units made. In my experience anything with UN307 or higher is a 1-chip. Keep in mind you may find a UN800 or UN900, those were refurbished units by Nintendo and not necessarily a 1-chip.

Amigo podrías hacer un tutorial de reproducción de cartuchos de snes estaría genial..

Andres Ruiz Si te refieres a cartuchos de reproducción, no sé cómo hacerlos. Además, ni siquiera tengo un programador de chips. si te refieres a la reparación de cartuchos SNES, tengo algunos en mi canal y tengo más por venir.

Me parecen muy buenos tus vídeos y pues yo e tratado de hacerme un programador willem pero no e tenido exito.

Nice, these have gone up quite a bit now.

@@PunkNDisorderlyGamer what would a clean unit go for?...is it worth the mod for resale factor?

It corrects the brightness a bit. But if you don’t want to do it you will still be happy with the standard RGB image.

etsy.me/2VuFcFI Here’s where I got mine. It’s a super high quality repro, nice label and works well. As for the NES test cart, I don’t own one perhaps he sells them as well.

I’m not sure, that’s very strange I would try another copy of the game, if it still persists then your console may have an APU fault. If your console has a removable SHVC I would try reseating it or replacing it. Could also be bad capacitors but, you mention the console doesn’t have music only on the title screen, other parts it’s fine?

Ok just to be sure I I double scrubbed everything and re soldered all connections and no dice.also I tried to remove the pin connectors and it's like it's super glued in.any ideas?also yes i removed all retaining screws.

I still can't remove my pin connector bar.its like it's stuck with super glue.any ideas on how to remove it w/O damage?

Jacinto Gomez you have to clear the through holes, if you have a desoldering gun it’s easy. If you have a vacuum pump or desoldering braid it takes more effort.

@@PunkNDisorderlyGamer ok there's thin lock clip tabs but I've already in clipped them and the two retaining screws.

No you will have to desolder it.

​@@PunkNDisorderlyGamer thanks for the response, that is good to know. I took apart my '03 and cleaned it just like in all these cleaning videos, and I actually also had the first series SNES as well, but I can't remember the number for that. That connector came right off, and I cleaned the inside of that SNES as well, however, after the cleaning and trying different cables and cartridges, I cannot make either of those consoles work.

You won’t get any power if the fuse is blown. It’s actually quite common fault among SNES, and a very easy fix.

@@PunkNDisorderlyGamer word thanks for fast response man. i just found a 1 chip 03 on ebay and i ordered all the parts to do what you did in the video

A E cool I hope all turns out well, if you need help I’m here. 👍

www.retrorgb.com/snes1chipdiy7314.html