Easy fix - Toyota 4runner/FJ Cruiser/Tacoma/Tundra/GX460 • Biggest Problem/Flaw

Рет қаралды 13,733

10 ай бұрын

I should have made this video a while back.
#fjcruiser #4runner #tacoma #tundra #diy #fixit #issue #frame #rustbelt #airconditioning #lexus #toyota
I want to start by saying that These body-on-frame Toyotas are great reliable vehicles… but
Considering that you have already undercoated your frame, did you re-route you A/C Evaporator drain hose?
You might not want to miss this one.
Parts needed:
3/8 Plastic hose straight barb fitting $8
amzn.to/3LDxjGu
Or
3/8"(10mm) Hose Repair Kit Hose Connector Barb (comes with clamps) $5.39
amzn.to/3PCNxRU
Hose 10mm(3/8-inch) Inside diameter x 14mm(9/16-inch) Outside diameter $8
tinyurl.com/yznmarx9
Or
amzn.to/3SpUfwL
Tools used:
Trim removal Tools
amzn.to/46r2I7d
Hose cutting Pliers
amzn.to/3LDxKAS
Cute little flying Bear Pilot Car Freshener
amzn.to/3Q2WdlE
Vikings Garage Patch
vikingsgarage.etsy.com
Previous videos covering the Frame topic:
Actual Frame replacement undergoing
• Warning Toyota FJ Crui...
Frame undercoating DIY
(With of the shelf Products)
• Toyota 4Runner • RUST...
Crc Frame treatment (internal)
• Toyota 4Runner/Tacoma ...
Linex Frame undercoating (exterior)
• Toyota 4runner/Tacoma ...
Thank you for watching and don’t forget to share it with someone that has a body-on-frame Toyota or a body-on-frame vehicle that might have that drain facing the frame.
Let’s keep these beautiful trucks on the road longer.
#4runner #offroad #toyota4runner #4x4 #4runnertrdoffroad #armygreen #trdoffroad #4runnersdaily #letsgoplaces #green4runner #runner #toyota #overland #runnernation #trd #runnermafia #yotamafia #overlanding #5thgen #adventure #runnersdaily #trdpro #yotalife #trdoffroad #yota #offroading #explore #mustwatch

Пікірлер: 206

@Papolucho702 10 ай бұрын

You and the Cat Care Nut are my go to for certain Toyota maintenance and preventive care tips. Y’all should do a collab one day.

@VikingsGarage 9 ай бұрын

You know, I think that would actually be a great idea!! Great guy, I’m sure I would enjoy a collaboration with him!! 💯

@ian0841 10 ай бұрын

I watch a lot of Toyota content on KZfaq and this is the first time I have seen a video like this. Great content as always!

@VikingsGarage 10 ай бұрын

Much appreciated!! Thank you!!

@gothamems5628 10 ай бұрын

Dude…this is one of the best, most inexpensive mods EVER! Thank you for your commitment to the little guy!

@VikingsGarage 10 ай бұрын

🤘🏻🙏🏻 Always!!

@caddydaddy9536 10 ай бұрын

Fluid Filmed my 2020 4Runner thanks to Eric O, now this beautiful tidbit. Thank you to this community for all the pertinent you provide! Continued success on your channel!

@VikingsGarage 10 ай бұрын

Right on!! And Thank you for your support!!

@leardi58 10 ай бұрын

As always thanks for keeping us updated on our 4runners, nice haircut brother 👍👊

@VikingsGarage 10 ай бұрын

Thank you Sir!! 😅

@jasonmills1091 10 ай бұрын

Thanks bro! You always coming through for us 4Runner people!!!!

@VikingsGarage 10 ай бұрын

You got it!! 🤘🏻

@veedubya4636 3 ай бұрын

Us FJ folks too!! 😀

@VikingsGarage 2 ай бұрын

@veedubya4636 Hell yeah 🤘🏻 Now officially a member of this special group. 2008 Sandstorm 😉

@jel517 10 ай бұрын

Good morning and thank you. I heard about this problem years ago and I was going to do "something" on my 15 Tacoma but I never did. Came across this video the other day and decided I was going to take care of it on my 22 4runner. Ordered the plastic 3/8th barb couplings and new push clips, (cause whenever I take them out one of them seems to break). Got the 3/8 ID hose at Advanced auto. I started with a 12" piece and ended up cutting about an inch off AFTER install ( so about an 11' piece). I wanted to make sure it cleared the frame. It's tucked in just like you have it with about a 1/4" hanging past the frame. It looks factory. I did happen to watch a bunch of other video's of people doing it their way. This is by far the BEST way I found. Neat, Simple AND I can keep a visual on it from time to time to make sure the drain hasn't clogged.

@VikingsGarage 10 ай бұрын

Absolutely, the fact that it’s visual is one of the reasons why I routed that way (not to mention through the inside, your dealing with exhaust heat) Thank you for sharing + I’m glad you got it done!! Safe travels!! 🤘🏻

@TheRealDrGreenbaum 10 ай бұрын

Thanks, I needed to figure out how much hose to measure out

@Treetopflyer777 10 ай бұрын

Parts ordered. Thanks for the great PSA!!

@VikingsGarage 10 ай бұрын

👏🏻👏🏻👏🏻

@dmb350 5 ай бұрын

Absolutely love this channel. One of two MUST subscribe channels if you own a 5th gen 4Runner.

@VikingsGarage 5 ай бұрын

I appreciate your kind words!! 🙏🏻

@theotherbrad5650 10 ай бұрын

As always, super amazing content. Thank you!

@VikingsGarage 10 ай бұрын

You’re very welcome!! 👍🏻

@wamps3370 10 ай бұрын

THANK YOU for this very cost effective improvement!!!

@VikingsGarage 10 ай бұрын

You’re very welcome!! 💪🏻

@humanbean123 Ай бұрын

Thanks! This was a really helpful, easy mod!

@VikingsGarage Ай бұрын

🤘🏻

@Johnnybones318 Ай бұрын

Awesome video! Definitely gonna do this to my FJ. Thanks!

@VikingsGarage Ай бұрын

💯👏🏻👏🏻

@chrisridebike8 5 ай бұрын

Perfect vid. I wanted to extend my drain line and this had all the info

@VikingsGarage 5 ай бұрын

That’s awesome, yeah get it done sooner than later.

@RVH-io3dr 7 ай бұрын

Thanks for the video. Going to do this to my 4runner in the spring.

@VikingsGarage 7 ай бұрын

👏🏻👏🏻🤘🏻

@davidhart17 9 ай бұрын

Thanks for the excellent tip and instructions! Just Just got it done 👍

@VikingsGarage 9 ай бұрын

🙏🏻👏🏻

@cpfb68 9 ай бұрын

Excellent tip and again thanks for the great video! Keep up the great work! Much appreciated!

@VikingsGarage 9 ай бұрын

Thank you!! 🙏🏻

@ruckinehround6965 10 ай бұрын

Thanks for the tip. Just picked up my 2023 lunar rock TRD off road premium. Plan to have this car 20 years or more.

@VikingsGarage 10 ай бұрын

Go get this done, and Congratulations on the new ride!! 🎉

@trailrunnah8886 8 ай бұрын

Excellent info! Thanks for posting this.

@VikingsGarage 8 ай бұрын

Absolutely!!

@msrobot007 9 ай бұрын

Thanks so much for this video! I modified my 2018 Limited yesterday! 🤓

@VikingsGarage 9 ай бұрын

👏🏻

@angelclemente9501 10 ай бұрын

Love your videos! Wicked helpful!

@VikingsGarage 10 ай бұрын

Thank you!! 🤘🏻

@acet7 10 ай бұрын

Have to add this one to my list of things to do, thanks for sharing.

@VikingsGarage 10 ай бұрын

😉👍🏻

@mikesweeney5685 10 ай бұрын

Hey VIking, I've been a subscriber for awhile now and really like the videos. Also envious of the green OR 4Runner! Mine is a 2015 Limited. I took a look at my AC drain line and sure enough it dumps right on the frame. I went ahead and did the mod, but interestingly I have no rust on the frame in that location or anywhere else for that matter. Oh well, I plan to keep it forever so it's good cheap insurance. I'm sure my frame is rust free because of where we live (west Texas). It is very dry and we rarely ever get any snow. If I move to a more humid climate, I'll probably go ahead and get the LINE-X undercoat put on. Back to your channel though, it's all good information and I check out your videos before I try anything new!

@VikingsGarage 10 ай бұрын

I appreciate your support!!🙏🏻 Texas, great weather… cheers my friend 🍻

@Levi.Jaeckel 10 ай бұрын

Such a valuable tip, thank you for this video.

@VikingsGarage 10 ай бұрын

Your very welcome!! 👍🏻

@OJCoz 9 ай бұрын

thanks for the heads up brother. good video and I will be doing it to my GX

@VikingsGarage 9 ай бұрын

👏🏻👏🏻🙏🏻

@g.fortin3228 10 ай бұрын

Love this Paul !!!! Will do !! And I hadn't seen the holes on top of frame, might as well squirt them all with fluid film too ! I did the lower ones and side one.. didn't see these. Thank you SO much ! ( edit: And ..Loving those wheels !! )

@VikingsGarage 10 ай бұрын

Thank you Sir!!

@emmanuelmatos8942 9 ай бұрын

This video is gold. Just did mine, an SR5 2020 5th Gen. My hose is on the longer side though. I'll keep my eye on it but tested it and the water drains straight to the ground where it's supposed to be.

@VikingsGarage 9 ай бұрын

That’s awesome 👏🏻

@peterf4719 2 ай бұрын

Just did this mod. Definitely take the wheel off if you want to use clamps and have easy access. I was barely able to do it and couldn't get one of the clamps on. Will do it later this year when I'm swapping to winters.

@albetherechillin 10 ай бұрын

Eee this was nice man. Great idea

@Glasscitycarnerd 10 ай бұрын

Need to do this on mine this week! Awesome!

@VikingsGarage 10 ай бұрын

👏🏻

@dickmorissette2900 10 ай бұрын

Thanks for sharing! The mod is done!

@VikingsGarage 10 ай бұрын

👏🏻👏🏻

@InGratitudeIam 10 ай бұрын

AWESOME!!! Thanks, Paul!

@VikingsGarage 10 ай бұрын

Your welcome!!

@hectorrivera9894 3 ай бұрын

Thanks for the video! Excellent tip…..Tomorrow, I’m going to the Parts Store and pick up a connector and hose and knock this out.

@VikingsGarage 3 ай бұрын

Absolutely!! 👏🏻

@veedubya4636 3 ай бұрын

Thanks!! I just did my FJ yesterday. The drain line was shorter than on your 4runner. It took me longer to find my tool to pop the fender guard fasteners than it it did to actually attach the hose.

@VikingsGarage 2 ай бұрын

Crazy right 😅. Great job 👍🏻

@ToyotaTacoma-js6on 10 ай бұрын

Great idea. Thanks so much for the information

@VikingsGarage 10 ай бұрын

You’re very welcome!!

@Thankyou_3 10 ай бұрын

Thank you 🙏 sir. Appreciate all your help and videos. God bless you!

@VikingsGarage 10 ай бұрын

👍🏻🙏🏻

@Thankyou_3 10 ай бұрын

@@VikingsGarageI followed your instructions exactly and was done in less than 5 minutes. Thank you so much again for all your help to bless people. God bless you 🙏

@VikingsGarage 10 ай бұрын

@Thankyou_3 That’s awesome!! I appreciate you. 🙏🏻

@montymuseitef53 10 ай бұрын

Thank you for the tip !!

@VikingsGarage 10 ай бұрын

You got it!!

@joeythedime1838 10 ай бұрын

Fantastic tip!!!! Thank you.

@VikingsGarage 10 ай бұрын

👍🏻

@stevengoldenberg5362 4 ай бұрын

Love your videos, not sure about the one handed attachment of the hose as I was fighting with it under my truck with both hands and got it most of the way on! Good fix for sure.

@VikingsGarage 4 ай бұрын

👍🏻

@knotshore5957 7 ай бұрын

Thx for the tip

@VikingsGarage 7 ай бұрын

👍🏻

@jeffmclinn3168 10 ай бұрын

Great easy preventative fix. Thanks again. At First I thought you were going to bring up extending the axle housing breathers. Maybe next?

@VikingsGarage 10 ай бұрын

Somewhere in there, I’m sure we will. 😉

@ualfltdispatch Ай бұрын

Thanks so much!

@VikingsGarage Ай бұрын

👍🏻

@lirimlajqi3124 7 ай бұрын

You are a legend

@VikingsGarage 7 ай бұрын

Thank you Sir!!

@MyRCChannel-CJScott 10 ай бұрын

Another informative video! BTW, this morning I'll be dropping a deposit on one of the last 2023 4Runner TRD Pros in Solar Octane... it's out at sea on it's way to a nearby harbor and when it arrives, it's mine! WooHoo! The sales manager at my local dealership did a search and let me know which dealership in the area was scheduled to receive one more Pro in Solar Octane. Very cool guy!

@VikingsGarage 10 ай бұрын

I’m excited for you. Congratulations!! 🎉

@MyRCChannel-CJScott 10 ай бұрын

@@VikingsGarage Thank you! I'll be taking advantage of a lot of your tips tricks and mods. Question: Why do so many lift options exclude the TRD Pro? Don't all the trims share the same basic chassis, shock mounts, etc. not including the fox shocks? I'm not anxious to lift my truck, but I might want the option down the line. I might settle for slightly larger tires.

@VikingsGarage 10 ай бұрын

@MyRCChannel-CJScott I’m not sure on the TRD PRO exclusions. 🤷🏼‍♂️

@Notification93 10 ай бұрын

was waiting for this video after watching your Short :)

@VikingsGarage 10 ай бұрын

Right on!! Thank you Sir!! Get it done, super easy. A must if you plan on owning it long term.

@Notification93 10 ай бұрын

@@VikingsGarage Thanks and I will! Btw, I just dropped my 4Runner at an XLINE shop for the undercoating (I went with it after watching your video), and I was wondering if they coated the inside the frame for your 4Runner?

@VikingsGarage 10 ай бұрын

@Notification93 👏🏻👏🏻 Very good. They only did the outside, the inside I’m doing it like I did on the red 4Runner in this video: kzfaq.info/get/bejne/pdV8eN2b1bjOiGg.htmlsi=j3i-nm8gNhmRtQnb Good luck!!

@Notification93 10 ай бұрын

@@VikingsGarage Thanks! I'll try to do it soon on my own but I'll have to do it on the ground as I have no access to a lift :(

@VikingsGarage 10 ай бұрын

@Notification93 you don’t need a lift . 👍🏻

@jaystepp150 14 күн бұрын

Solid advice

@VikingsGarage 14 күн бұрын

👊🏻

@rafalsabat5408 10 ай бұрын

Thanks master

@VikingsGarage 10 ай бұрын

🙏🏻

@lostagain2992 10 ай бұрын

Nice! Thank you!

@VikingsGarage 10 ай бұрын

👍🏻

@johnholt4348 10 ай бұрын

Thanks

@VikingsGarage 10 ай бұрын

Your welcome!!

@pall5114 9 ай бұрын

what a simple preventative measure, thank you!. Although I couldn't see the drain and you inserting the coupling it seems clear where it is so will give it a shot. Any risk the drain gets clogged from the coupling? great video, I have seen your 4R videos and all great, keep it up. new subscriber. Where is your repair center or do you work outside, I am in the Tri-state area.

@VikingsGarage 9 ай бұрын

I am currently working at a Toyota dealer. A/c drains can get clogged, it’s smart to shot pressurized into it every so often. I appreciate your support!! 🙏🏻

@txc500 8 ай бұрын

That is amazing. Toyota couldn't think of that?

@VikingsGarage 8 ай бұрын

I know right.

@juancarlosguzmanrdrz 10 ай бұрын

I did thanks 👍

@VikingsGarage 10 ай бұрын

👏🏻👏🏻

@davehill7484 4 ай бұрын

I did this modification on my 2019 Tacoma and just recently bought a 2024 4Runner with apparently the same design problem so off I go to the local Lowe’s or depot to find the barb fitting and 3/8” hose😎👍

@VikingsGarage 4 ай бұрын

Heck yeah!! 👏🏻💪🏻

@davehill7484 4 ай бұрын

Love the channel my friend 👍

@VikingsGarage 4 ай бұрын

Thank you!!🙏🏻

@toyo1267 10 ай бұрын

Great idea and video instruction. Your 4runner is looking good. Thanks for the video. Toyo12

@VikingsGarage 10 ай бұрын

Thank you Sir!! 🙏🏻

@GG-un5wk 10 ай бұрын

This was a great video! Thx man. I did mine and of course I had a bit of rust from that hose. Why Toyota would do that ah?

@VikingsGarage 10 ай бұрын

🤷🏼‍♂️

@toyo1267 10 ай бұрын

I extended the drain line for the AC as you showed, good idea. I noticed on the interior center vent of your 4Runner you have the nose of a plane with propeller, where did you find it? I I also have a 2022 TRD ORP. Great vehicle. Thanks for all your work. Toyo12😎

@VikingsGarage 10 ай бұрын

That was an Amazon find: amzn.to/3Q2WdlE My kids love it + it works great!!

@mariabarreiro9884 6 ай бұрын

Good Job Filho 👍💪 beijinhos 😘❤️❤️❤️❤️

@VikingsGarage 6 ай бұрын

❤️

@Brandon_osborn 2 ай бұрын

Thanks for the video! I definitely plan to do this and ordered the stuff from your description! One questions came to mind (granted I don’t know too much about cars). With the drain hose being in the wheel well/closer to the elements, do you think or have you experienced any clogging more frequently in the drain hose?

@VikingsGarage 2 ай бұрын

I usually haven’t seen any clog up… but I have the habit to shoot pressured air up the drain every other service, just in case. Thank you for your support!! 🙏🏻

@HighAltitudesCO 8 ай бұрын

Just did this to my 4Runner while it was on the lift getting it's winter coat of Woolwax

@VikingsGarage 8 ай бұрын

👏🏻👏🏻👏🏻

@johncellucci3024 9 ай бұрын

Your video caused the 3/8th hose to be either sold out or now $28. Probably just inflation:)🤣

@VikingsGarage 9 ай бұрын

Omg 🤣🤣

@sonnyblack5253 10 ай бұрын

My 99 rotted really bad in that one spot because of this.I will be doing this to my 18 for sure.

@VikingsGarage 10 ай бұрын

Sorry to hear, please do. It’s a silent killer.

@LexusGX460-OFF-ROAD 10 ай бұрын

ours lives in the desert where nothing rusts... i should check this frame area for scientific purposes... thanx 😊

@VikingsGarage 10 ай бұрын

lol 😅

@koko4kosh960 6 ай бұрын

Did you find anything?

@guillermodvl 9 ай бұрын

I will do this to my 4runner

@VikingsGarage 9 ай бұрын

👏🏻👏🏻

@bogieman101 5 ай бұрын

Crazy Toyota hasn't addressed this. How many other small easy fixes have they looked over? Never would have associated this kind of slackness from the big T. I just bought a '23 GX460 and it sufferers from the KDSS lean, another issue Toyota has just ignored over the years. Crazy they would allow all these KDSS vehicles to drive around leaning. But, I still love my Toyota's.

@VikingsGarage 5 ай бұрын

You’re absolutely right. Toyota still does beat most in reliability.

@Nunyobidne55 5 ай бұрын

10 inches is the magic number

@VikingsGarage 5 ай бұрын

👍🏻

@toyo1267 10 ай бұрын

Thank you, Sir. Toyo12

@TheSponge945 10 ай бұрын

Does it drain there even when AC is not running? I have dribbles which I assume are condensation come out of that hose even when I didn’t use AC?

@josecrespo4817 5 ай бұрын

Hi sir thanks for the video..i have a question..in your previosus 4 runner 5 gen the red..did you change your pcv valve.?.and in how many miles thanks

@VikingsGarage 5 ай бұрын

Changed it at the same time as the spark plugs 100k.

@PocketsandOutlaw 9 ай бұрын

It's as if somebody at Toyota went: "Hmmm... Our frames aren't rusting in hot climates and our sales are down.... I KNOW! Route the only water exposure in the entire state of Arizona right onto the frame! We even save $0.01 on having a foot less of tubing!"

@VikingsGarage 9 ай бұрын

I know right!! 😅🤣🤣

@Thankyou_3 10 ай бұрын

I love your postlude music, is it your personal or I can look for it. What is name for it please….🙏

@VikingsGarage 10 ай бұрын

Thank you!! It’s a song from the app to edit my videos that spoke to me. It’s called “Get out Alive” by Arthur Basov

@Thankyou_3 10 ай бұрын

@@VikingsGarage Thank you so much 🙏

@b.m.c.8755 9 ай бұрын

Dear master, what was the outside diameter of the evaporator water drain hose on the 4Runner. I would like to sleeve over it. I don’t want any mud to build up over time in between the barb connector.

@VikingsGarage 9 ай бұрын

I don’t know. Would have to measure it

@wolfeadventures 10 ай бұрын

In that location debris could get thrown and possible block the line? How about snow and sleet blocking it?

@VikingsGarage 10 ай бұрын

I’ve had it that way, in the red 4Runner for 5 years (zero issues) Snow and all 😉

@darrinvandemark4781 10 ай бұрын

Do you run the AC with snow and sleet on your 4runner?

@VikingsGarage 10 ай бұрын

I do not.

@TedEischeid1960 10 ай бұрын

@@darrinvandemark4781Whenever you have it set to “defrost”, typical in winter, the AC is on during that setting.

@Allthingsmisc 10 ай бұрын

Hi this is not related to this video but I replaced my silver rails with black ones Did I need to put any silicone while bolting it back I just put some thread lock please advise

@VikingsGarage 10 ай бұрын

I’m literally showing this in the upcoming video… I use silicone every time. It’s piece of mind. I’ve seen thread lock leak, silicone never. 👍🏻

@Allthingsmisc 10 ай бұрын

@@VikingsGarage thanks bud

@Allthingsmisc 10 ай бұрын

@@VikingsGarage hi can you please suggest the right silicone for the roof rack I would greatly appreciate that thanks

@VikingsGarage 10 ай бұрын

@Allthingsmisc Honda bond.

@jarediz6624 10 ай бұрын

Even if I don't live in the rust belt, should I still do this?

@VikingsGarage 10 ай бұрын

💯 a must, this applies to everyone that owns a Toyota body-on-frame. (4Runner/FJ Cruiser/Tacoma/GX460)

@jarediz6624 10 ай бұрын

I'll do it!@@VikingsGarage

@VikingsGarage 10 ай бұрын

👏🏻👏🏻

@edmiller3759 10 ай бұрын

Great idea but not necessary if you don’t live in one of the salt belt states. Frame rust have been problems mostly in the salt belt states.

@VikingsGarage 10 ай бұрын

@edmiller3759 you’re missing the point.

@MikeGeorge392 2 ай бұрын

Are there any issues I have this mod now installed but I want to make sure it’s not going to screw up any parts of the car?

@VikingsGarage 2 ай бұрын

And why would I recommend something like that. Don’t you think by you saying that… It’s borderline insulting.

@starwarskong 7 ай бұрын

😮

@VikingsGarage 7 ай бұрын

Scary stuff right!!

@tomc8115 10 ай бұрын

The easier solution would be to convince the wife that we don't need to have the AC on in the summer... Who am I kidding! 😂 I'm doing this asap. Thanks for the tip, Viking!

@VikingsGarage 10 ай бұрын

😆

@nuckleheadzgarage8360 10 ай бұрын

does this apply to a 4th gen to?

@VikingsGarage 10 ай бұрын

Unfortunately, YES!!

@ry5tyle 10 ай бұрын

Oh no the hose in unavailable on amazon!

@VikingsGarage 10 ай бұрын

3/8 hose from your local hardware store.

@VikingsGarage 10 ай бұрын

Try this one amzn.to/46uY9bZ

@ry5tyle 10 ай бұрын

Thanks appreciate it. Probably stop by hardware store.

@VikingsGarage 10 ай бұрын

@ry5tyle please do, it’s super easy to do.

@danielfurr5409 Ай бұрын

Mine is clogged how do I Unclogged itit

@VikingsGarage Ай бұрын

Either with pressure air blown into it, or use a snake tool. A flexible smaller coat hanger works too.

@danielfurr5409 Ай бұрын

@@VikingsGarage were exactly is the other end of the hose? Am I able to take blower motor out or something inside and find the other end to clean it out?

@VikingsGarage Ай бұрын

@danielfurr5409 the other end is under the passenger side carpet, connected to the bottom of your a/c air box.

@danielfurr5409 Ай бұрын

@@VikingsGarage thanks. My Carpet is soaked wet due to it not draining

@danielfurr5409 Ай бұрын

@@VikingsGarage it worked. I pulled the tube completely into the 4runner.. hooked up the air nozzle...and could hear the water bubbling when blew air in. Pulled nozzle out and a freaking quart of water came gushing out..lol

@maxkrauss4155 Ай бұрын

While this mod works well, I can't stress the importance of keeping the line free and clear. With the new hose, it's more likely to suck in water then it was before. If you don't get a lot of rain it won't be a problem.

@flatliner2713 10 ай бұрын

I be damned. Simple as breathing.

@VikingsGarage 10 ай бұрын

🤷🏼‍♂️👍🏻

@KendrasEdge757 10 ай бұрын

Was unsub’d from your channel smh yall check your subscription.

@VikingsGarage 10 ай бұрын

Oh boy 🤦🏼‍♂️ … well I’m glad you got the very important information. I should have made this video a while back.

@KendrasEdge757 10 ай бұрын

@@VikingsGarage yeah maybe, but glad you did it nonetheless. I’ve known about this but kept forgetting or putting it off and now that I’ve seen the video I can stop putting it off and get it done. So appreciate the reminder lol

@KendrasEdge757 10 ай бұрын

@@VikingsGaragedid it today. Hit advanced and got a 3/8” heater hose 12” and a 3/8 barbed coupler and added two hose clamps. Then I ran it the same route you took through the bottom of the splash skirt and then I cut off probably 4” and then another 2” and that leaves it to the bottom of the frame. Probably didn’t need the two clamps but 🤷‍♂️ wth right.

@VikingsGarage 10 ай бұрын

@KendrasEdge757 👍🏻👏🏻

@beaviskornholio2754 9 ай бұрын

I have a question and it might be the dumbest one you ever got. With the way that manufacturers and dealerships like to decline warranty repairs. Would this void your factory and extended warranty. Also for rain guards on your doors and cat shields. Sorry to bother you about this but you can give the most accurate answer since you work in service at the dealership. Thanks in advance and have a good weekend.

@VikingsGarage 9 ай бұрын

None of the ones you mention affect the vehicles performance or functionality… so they won’t void your warranty.