Vinyl Siding Installation - CERTAplank by Certainteed

Рет қаралды 25,544

Күн бұрын

In this video, I show you how to install vinyl siding. I will be using CERTAplank that is made by Certainteed for this vinyl siding installation. I show how to install vinyl siding starter strip, J Channel, outside corners, and many other vinyl siding accessories. If you need to know the basics of siding or details, this video will help. I get asked about how finish up a vinyl siding installation regarding the top piece so I went over that in detail as well. This video is packed with vinyl siding installation tips and tricks.I would like to thank Certainteed for sponsoring this video. #diy #construction
Visit bit.ly/CertainTeed-CERTAplank... to find the products used in this video.
Visit bit.ly/CertainTeed_Siding_Pro... to find other vinyl siding products from Certainteed.
My Favorite Tools And Supplies 👉 amzlink.to/az0KsA48iJTo2
Tools And Supplies Used In This Video👇
My Tool Belt Setup amzlink.to/az07AiPoIFfdi
Malco SL5 9 in. Snap Lock Punch amzlink.to/az0hXo1IKIvfp
RIDGID 18V Brushless Cordless Oscillating Multi-Tool amzlink.to/az0n7fgcQhQXI
18V SubCompact Brushless 1/2 in. Drill/Driver and Impact Driver Combo Kit amzlink.to/az01VqN1ZzeFu
Stanley 12-Inch Straight Pattern Tin Snips amzlink.to/az0yFFNbNYl81
DEWALT DWS780 12-Inch Double Bevel Sliding Compound Miter Saw w/ DWX723 Heavy Duty Miter Saw Stand amzlink.to/az0ynku50jADg
More Helpful Related Videos👇
How To Install Soffit, Fascia, And PVC Board • How To Install Soffit,...
How To Install Vinyl Siding • How To Install Vinyl S...
How To Install Vinyl Siding (part 2) • How To Install Vinyl S...
How To Install Board And Batten (vertical siding) • How To Install Board A...
🟢 Become a channel member:
/ @theexcellentlaborer
🔴 Subscribe to this DIY channel: kzfaq.info...
🟡 Check out my Amazon store: www.amazon.com/shop/theexcell... . Here you will find tools and supplies used in my videos. (DISCLAIMER- I am an Amazon affiliate. I get a small commission that helps support the channel at no extra cost to you)
Timestamps
Intro 00:00
Corner Installation 00:57
J-Channel Installation 10:19
Electrical Box & Mounting Block Installation 17:48
Starter Strip Installation 24:30
Vinyl Siding CERTAplank Installation 28:56
Window Undersill Trim Installation 39:24
Finishing Top Piece Vinyl Siding 48:48
Finished Product 52:09
Disclaimer: This video is all based on my personal opinion and is for entertainment purposes ONLY. I am not a financial advisor, CPA, attorney, tax advisor, electrician, plumber, housing contractor, designer, or any type of profession to give advice. I am just a consumer sharing my experiences and research. If you do need knowledge for those types of things, I will advise you to seek help for those professionals.

Пікірлер: 47

@JohnR9965 7 ай бұрын

Vinyl is Final Was a saying back in the day when I used to do siding. They have come along way with options since. I have laid plenty of certain teed vinyl siding many years ago.

@TheExcellentLaborer 7 ай бұрын

Vinyl siding a great product these days! Thanks for commenting!

@davidmaier343 7 ай бұрын

You’re very good at explaining which is why I watch.

@michaelkeller5270 4 ай бұрын

I just started taking a look at repairing/replacing the siding on my house myself, and this was one of the most informative, detailed and precise video installations I've seen yet. Those planks look great!

@geemanone2039 5 ай бұрын

A little something I found that worked well for me. When cutting down the width of long pieces of siding I used either left or right aviation snips. I am right handed and I found that when using the "left snips" (cutting from right to left on the work area) and "rolling" the snips away from the cut off made it very easy to cut along the line and avoid the binding issue of straight snips. It would be left to right when using the "right snips". It worked for me hopefully it can help others. Now that my shed build is done and all siding installed I want to say thank you for your videos. I had never installed vinyl siding previously and I truly believe I would not have been able to without your videos. I learned allot here and along the way of my build!

@davidmaier343 7 ай бұрын

‘With that being said’ LOL😅 it’s good to see you in another video. I’m done with my siding but enjoy watching/learning yours. This time the pop riveted corner detail was nice. Keep up the good work.

@TheExcellentLaborer 7 ай бұрын

Yes I said that phase a good bit. GOOD CATCH! Thanks a lot for watching!

@davidportmess6406 7 ай бұрын

Turned out awesome!!!

@TheExcellentLaborer 7 ай бұрын

Thanks for the support David!

@TB-LivingFree 7 ай бұрын

Quality information and insights once again, thank you sir

@TheExcellentLaborer 7 ай бұрын

Thank you so much! That means a lot. I hope everything is going well for you!

@BobSmith-qg4jj 4 ай бұрын

27:00 That smirk comes from experience lmao 😂

@jeffdeluca1153 5 ай бұрын

Nice work as always!

@dania8969 7 ай бұрын

Very informative

@TheExcellentLaborer 7 ай бұрын

Thanks Dania!

@ayubbuildingconsultants 7 ай бұрын

Great video as always Josh, especially the detail !(Waiting for a kitchen counter top installation video as well🙂. Hope it's in the pipeline)

@TheExcellentLaborer 7 ай бұрын

Thank you! Yes I will be making a video on that topic. Stay tuned!

@ayubbuildingconsultants 7 ай бұрын

Awesome Wish your channel great success !@@TheExcellentLaborer

@MarcusHamilton-vk1tt 4 ай бұрын

You’re awesome bro

@TheExcellentLaborer 4 ай бұрын

I really do appreciate that. I hope this video is helpful for you. Be sure to stay tuned for more!

@plumbbuild6517 7 ай бұрын

Good job on your vinyl siding have you ever thought about bending a piece of metal for over top the garage door and entry doors for a drip edge, when I was installing siding the inspectors would turn us down unless we had a flashing/drip edge. Thanks for the videos

@TheExcellentLaborer 7 ай бұрын

I flashed the door using flashing tape as I showed in the this video kzfaq.info/get/bejne/oqyBlcZo0dq9Zps.htmlsi=zEXs8X-L26q4y1So . Thanks for watching!

@plumbbuild6517 7 ай бұрын

@@TheExcellentLaborer I understand that you installed flashing tape , but like I had mentioned the inspectors were I use to install made us install a drip edge, we would make it 4” high and turn out the width plus an 1/8 to a 1/4 and then about a 45 degree down 1/2 inch , the inspectors wanted to see a rain drip edge on every opening.

@JCiTrusTinYou 7 ай бұрын

I’m installing vinyl siding on my home and I’m loving it! I really like working with it even with my bad back and sore legs at 60 years old…lol My home is over hundred years old in stucco. Altogether stucco/cinderblock/plaster my walls are about 6 inches thick or so. Not insulated in the slightest so I’m insulating the outside with half inch green board foam. That’s just a quick note on that. It’s a double home and in between my neighbors and my front door I put up two furring strips and the insulated board and to opposing Jay channels which has approximately 7” between them. I kind of forgot to put furring strip down the middle so I could nail the little pieces of siding ( double Dutch lap 4 1/2 Panels ) So, my question is without getting into cutting the insulation and fitting a furring strip in there, I put a little adhesive behind the panel along the slots …? I know that you’re supposed to be able to allow for expansion/contraction of the material but the pieces are so short , should I be concerned about that ..? OR … since the pieces are so short in length, how about no adhesive, no nailing , just snapping them together ? OR … Use heavy fishing line past through the slots and pulled up and nail in the end of the string up above the door and covered with full panels….? Thanks for your video I’m learning a lot…👍🏼🙂

@aaronwiley5436 7 ай бұрын

Nice video...would you consider doing a full video on bending coil and the many different bends on the brake?

@TheExcellentLaborer 7 ай бұрын

Thanks! I hope to do a video like that eventually.

@aaronwiley5436 7 ай бұрын

@@TheExcellentLaborer I know if anybody can do it, you will do an Excellent job at it.

@9dquimby 5 ай бұрын

Where do you buy the electrical box? Is there a model number on it? I cant find it anywhere online.

@user-ic5bh4gp2i 8 ай бұрын

👍👍

@TheExcellentLaborer 7 ай бұрын

Thanks!

@tannerladwig7879 4 ай бұрын

I don't understand how you secured the last piece of siding towards the top. It appears as if you just pushed it up there. We get some nasty winds where I live, so I don't see that working here. Please explain

@mechamoon1397 6 күн бұрын

what do u use at the bottom and top for starter and top finnish ?

@user-mk8qr3lg1c 7 ай бұрын

Hey Josh, love the build your own house plan. Curious - i don’t believe you are a licensed plumber, electrician, or hvac. When you build your house, do all your own work, as long as it passes code/inspection… you are good to go to sell to the public? I know every area will be different, but im about to go this route in the next 12 months. Thansk in advance, love the channel.

@TheExcellentLaborer 7 ай бұрын

Hey Thomas! I wish you luck with your endeavor you are wanting to do. In my jurisdiction, we can build our own houses and do all of the trade work as long as it is inspected. Yes, we then can sell the house after it has passed all inspections. You are right, every jurisdiction is different, so it is best to talk to your local jurisdiction and see the details. I hope that helps! Thanks a lot for watching, and I appreciate it!

@plumbbuild6517 7 ай бұрын

We can build houses in our jurisdiction aswell but good luck getting a loan from the bank if you’re not a contractor 😅 I’ve built several houses here but mostly for customers

@user-mk8qr3lg1c 7 ай бұрын

Really appreciate the response, you da the man! @@TheExcellentLaborer

@user-mk8qr3lg1c 7 ай бұрын

I hear that. From what I hear, a Heloc is a good way to go, so you’re not waiting on the banks to pay for the next phase. Ultimately, My plan is to get to the point, where I don’t need the banks. @@plumbbuild6517

@tammywood3684 7 ай бұрын

When you lay the j Chanel do you over lap on top, or under the next piece?

@TheExcellentLaborer 7 ай бұрын

I have to overlap 1 inch. The direction depends on which angle you want to see the lap from. I hope that helps!

@tammywood3684 7 ай бұрын

Yes that helps

@jgalindo9976 7 ай бұрын

Can you tell me what color is that. Thanks

@TheExcellentLaborer 7 ай бұрын

Castle stone . I hope that helps!

@lottiekenney636 7 ай бұрын

Where are you located, need hardie siding repair, here in Georgia.

@jeffdeluca1153 5 ай бұрын

Josh why again do you remove vinyl in the overlap area? Isn't this siding designed to install w/o adding all that work?

@Rocksolidamerican 5 ай бұрын

What is the name of the color ?

@TheExcellentLaborer 5 ай бұрын

Castle Stone. I hope that helps!

@mos8541 7 ай бұрын

As long as it NOT THAT hardi debacle, i have sided maybe hundreds? of homes with that hardi, siding planks, dragon tooth shingle/siding, board (lift one of those into place yourself!) and bat, they/it... is by far the worst building material ever sold to homeowners and forced on us to install. do you believe the siding you use would withstand Midwest winters? just asking i have no experience..., SFMF