Thank your nice words and glad it’s helpful. Your alway welcome to message me ion facebook if you have problems. Plenty do 👍

Any questions just ask i am on FB and instagram . Glad it helped . There other videos on the channel they may help you with your engine 👍

@shakyangler perfect I will have a look through the channel. What is your name on Instagram and I will look you up?

Hi Bob what boat do you have .

31 Camano Troll

Can you do me a favor and show me where on the TAMD41 is the temp sensor? My gages stopped showing engine temp and I need to check that sensor. I cannot find others talking about it.

@@bobp.6337 the temp sensor is on the right hand side of the thermostat hosing . The big water pipe that sits on the top of the engine that leads to the heat exchanger and also the thermostat housing . I hope I have described it enough so you can locate it.

Alan glad it helped . There are other videos on my channel on how to do others service parts

I changed oil and filters yesterday. Do you know the spec on the transmission fluid? Doing that next!

Dexon 2 transmission oil for my gear box also don’t forget the filter .

There are other videos that might interest you on my engine .

Glad you enjoyed. They are great engines and the boat handles a good sea.

@@shakyangler the only problem on my boat was a little bit of osmosis blisters, but luckily not involving the fiberglass but only the filler that they putted on some points between the gelcoat and the fiberglass.

I have finally bought a vacuum tank like yours. Very useful also on my other vehicles. I'm a little disappointed because every time I extract far less oil than I read on the user manual, also inserting the thin pipe in the dipstick tube... About 9 liter out and 9.5 liter in. The manual says 11, 5 Lt.

The cap is loose and just resting on the top but thanks for the tip.

There is a drain cock on the block that located underneath the rubber pipes that go from the heat exchanger and the exhaust elbow. Undo the cock and the coolant water will drain out. Then I back flush with a hose pipe on the same cock that you drained the coolant water out until the water flushed clear . Then I top up with antifreeze which I get from Euro car parts and it’s pink can’t remember the name of it

That’s the only way in an merry fisher 805 as there is no room under the engine. There is a sump plug if you can get to it.

John I have the Volvo lip seal shaft seal . I will be changing it next year when I change my cutless bearing . If you have the same Volvo seal then just grease in between the seals with the Volvo lip seal grease.👍

I have the Nanni engine but not sure what manufacture the stuffing box is. Do you have any photos of yours?

If you Google Volvo seal it will show you a picture . I used to have the nanni 4.90TDI in another boat . I know a fair amount about those engines. If you go on YBW motor boat forum I have put a fair amount about them on there . Jamielangston is my name on there.

Thanks for your help.

@@shakyangler so you have had the same boat with the Nanni?

The belt tensioner is a turn buckle that can be found at Tool station or B&Q . when you say you cant find my oil retractor due you mean the one for my gear box or the engine.

@@shakyangler I found the turnbuckle, I’m looking for your oil filter remover, I never seen one that looks like that one u have, I have filter remover’s that take off filters on my GMC truck those filters are not that big , like to find the one u have. Thanks for your help & no how. 👍

You can buy them at machine mart see description- Clarke CHT720 Oil Filter Claw Wrench , hope that helps 👍

@@shakyangler Thanks again Shaky 👍

I have 2 TV ‘s 🤣. They work off an inverter 12v to 240v with a digital aerial. You can also buy 12v TV’s .

@@yorumxyorum I use a standard inverter and not a full sinn but that said when I use my computer it can make it a bit jumpy but i mainly use it for my TV and electric blankets for winter boating.