Volvo Rear Spring Replacement
Рет қаралды 53,153
Күн бұрынThis is a rear spring replacement on a 2012 Volvo XC60. Support lower control arm with jack. Remove control arm to knuckle bolt. Lower jack, you may need to hammer arm down. Remove spring. Attach spring isolator to new spring and reinstall. Make sure to note the notches on the top and bottom spring perches. Jack up control arm, squeezing the spring and arm into the knuckle. Install bolt.
@Jezboyz Жыл бұрын
Fella… thank you! I was told £400 plus VAT to change the rear two springs Lifesaver!
@GibbysGarage15 Жыл бұрын
No problem! Good luck!
@user-ir9df8rd9e Жыл бұрын
Thanks from Russia!
@georgemwangi2896 2 жыл бұрын
Can I use long spring to lift up Audi A4 2004 model well what am I supposed to do
@michaelwise6970 3 ай бұрын
What's the torque spec on that bolt?
@yongcui5118 2 жыл бұрын
I am planning to do the same replacement on my XC60. How did you put the jack stand under the car. there is only one rear jack point of on each side. If you use floor jack to raise the rear, how did you put the jack stand and replace the floor jack? Thanks.
@GibbysGarage15 2 жыл бұрын
You can get creative depending on the make/model. I don't remember this car exactly since we don't have it anymore, but I believe I used the jack on the rear subframe to lift both rear wheels at the same time. Keep in mind this video is for the easier front wheel drive models. Give the car a push once its supported to make sure it's sturdy before working under it. Be safe and good luck.
@patrick.drives8730 3 жыл бұрын
bruh wtf your hair is nice as hell
@GibbysGarage15 3 жыл бұрын
fiance made me cut it :(
@michaelwise6970 Жыл бұрын
Do you need to do an enlightenment after replacing the rear springs??
@GibbysGarage15 Жыл бұрын
It's usually recommended after replacing any suspension components.
@YakyuBoy 2 жыл бұрын
Do you need a spring compressor for the rear springs?
@GibbysGarage15 2 жыл бұрын
If it's a suspension design like this one, it's probably safer to do it the way shown in the video with a floor jack. Trying to squeeze spring compressors in there (that might potentially slip off) seems sketchy to me. This way should be fine as long as you slowly lower the jack. Keep in mind I'm not a technician, so use my advice with caution.
@raduvladimirmihalache9226 3 ай бұрын
Apparently not
@jacobrollo406 2 жыл бұрын
Did you torque the bolts on the control arm connecting to the hub? If so, what spec?
@GibbysGarage15 2 жыл бұрын
I was not able to find a torque spec online. Somewhere in the 90-100ftlbs is usually plenty for suspension bolts of this size.
@prisono89 3 ай бұрын
Jakie to auto?
@osvaldaskupstas5075 Жыл бұрын
Do i need tracking after that??
@GibbysGarage15 Жыл бұрын
Alignments are recommended after replacing suspension components.
@donstevens7847 2 жыл бұрын
What body style is this on?
@GibbysGarage15 2 жыл бұрын
this is an xc60 with front wheel drive
@user-ez6hq2cz7m 2 жыл бұрын
На volvo s60 2014 г так же меняются???
@GibbysGarage15 2 жыл бұрын
должно быть похоже
@alwaystashi2926 3 жыл бұрын
👀👀👀
@TheSpartanMartin 9 ай бұрын
slow down lol
VOLLUX /// Автосервис автомобилей VOLVO & GEELY
Рет қаралды 23 М.
BILPRIME / АВТОСЕРВИС марки ВОЛЬВО и GEELY
Рет қаралды 49 М.
FCP Euro
Рет қаралды 60 М.
Mike the mechanic
Рет қаралды 10 М.
К.Б.С -Корпорация Бродячих Сусликов
Рет қаралды 4,1 М.
Misfit Garage
Рет қаралды 11 МЛН
Meanwhile in the Garage
Рет қаралды 8 МЛН
Обучение PDR удаление вмятин #pdrgarage #pdr #automobile #обучениеpdr #автосервис #краснодар #москва
PDRGARAGE SPB
Рет қаралды 1,4 МЛН
JAZZMOTO
Рет қаралды 2,4 МЛН