And if left? I just have to put up with the noises?
@GibbysGarage153 сағат бұрын
It might even go away on it's own because of brake dust buildup. It's your choice.
@josephyang82364 күн бұрын
Good to see you back out there man!
@GibbysGarage154 күн бұрын
Hell yea it's been a long hiatus, are you going to be at any OTA events this year?
@thisisntsergio13526 күн бұрын
Is this the part number? SU00311390 is the front the same as the rear?
@GibbysGarage156 күн бұрын
Rear is different, part number looks correct for OEM. I used a Timken bearing here in this video.
@toomuchcancer8 күн бұрын
Name of the wheels? Look sick.
@aisaaka9 күн бұрын
How much louder would you say this is then stock cold start? Is it super loud in person??? I don’t want to make my neighbors more mad since I have an 86 with an AWE touring exhaust but I wanna focus on my FRS build
@GibbysGarage158 күн бұрын
It is pretty loud.. but since tuning with OFT, it's not loud at all.
@bojr880811 күн бұрын
What size where the tools that's kind of all I need to know but I guess I'll just take the whole set and guess and check
@pauloconnor795113 күн бұрын
That copper slip is going to flick out with centrifugal force. Very not good !
@Forklifterforsale415 күн бұрын
Thank you very much unbelievably helpful I thought I fked up the install but my right front rotor only came with one loose clip not two like the other ones I got that day
@GibbysGarage1515 күн бұрын
Sorry to hear! You're very welcome!
@JuanRodriguez-qu9vh16 күн бұрын
How did you compress the cylinder
@GibbysGarage1516 күн бұрын
at 0:14 you can see I compress the cylinder with a vice clamp before taking it all apart. I find this way easier compared to doing it with the caliper off. Cheers!
@learnmarketing2117 күн бұрын
Thanks for the video, very helpful, I’ll try on my Touareg 2005
@GibbysGarage1517 күн бұрын
You're welcome!
@PanamaSticks20 күн бұрын
60000 mile change psr fhe maintenance schedule. Per instructions elsewhere, I fully warmed up the sngine to, supposedly, make the coil packs easier to remove.. I have strong hands. An hour later I still can't get any of the coil packs out. #1 was already separated, probably courtesy of my mechanic who wss supposed to do a compression check about 6 months ago..Never said a word to me about a broken coil pack
@GibbysGarage1519 күн бұрын
That is very frustrating, sorry to hear. Have you tried leveraging off of something on the top? Obviously avoid any of the sensitive bits. But they might break as well..
@PanamaSticks19 күн бұрын
@@GibbysGarage15I tried getting leverage. No good leverage points. I used a lot of force, trying to pull on the boots and coils at the same time.. Stretched the boots almost 3/4", but they didn't let go of the plugs. However the coils and boots have not pulled apart. At this point, I'm ready to put everything back together and let a mechanic deal with it. But wondering if all that pulling broke a wire connection to the plugs. Or is the connection just a pin that is sandwiched between the coil pack and head of the plug?
@GibbysGarage1519 күн бұрын
@@PanamaSticks Not sure about the pins. Have you tried a twisting motion as you pulled?
@VagBadgeSecrets22 күн бұрын
You just used a flat head for the plug right and did you reuse or replace
@kimaddanmanuel-uc2cn24 күн бұрын
Did you disconnect the battery before doing it? Im thinking about doing it myself but not sure if i have to disconnect the battery before replacing it. Thanks in advance.
@GibbysGarage1524 күн бұрын
I didn't, but it's probably a good idea to disconnect your battery.
@Ferretfanatic6924 күн бұрын
Common problem with certain pad manufacturers. Find a pad that fits and stick with them 👍🏻
@GibbysGarage1524 күн бұрын
I used to be a fan of Centric but they seemed to have dropped off recently.
@AndreaColasante297Ай бұрын
Audi S1 2016 all the same ?? Thank you 🙏🏼
@GibbysGarage1529 күн бұрын
As far as I know should be nearly identical! Check the manual to see if the quantity of oil is the same.
@AndreaColasante29726 күн бұрын
@@GibbysGarage15 does all the oil come out with the ramps?? Thank you Again so much You have been a great help to me so I do the maintenance myself thanks to you 🙏🏼
@GibbysGarage1526 күн бұрын
@@AndreaColasante297 I don't know that it makes a difference in how much oil comes out. At most you're leaving a few hundred mL in there. It's more important to do regular oil changes than to worry about "getting it all out." You're very welcome. Comments like these make making these videos all worth it!
@masterofnone7846Ай бұрын
Maybe cheap hardware?
@GibbysGarage1529 күн бұрын
That too!
@masterofnone7846Ай бұрын
Could it be cheap pads!?
@GibbysGarage1529 күн бұрын
Could be!
@kennydavis6026Ай бұрын
What's the orange stuff you were using with the brush?
@GibbysGarage15Ай бұрын
Permatex Orange Silicone Ceramic Brake Lubricant!
@brodywalsh4529Ай бұрын
yo can anyone help me out my friends adapter(yhe long stick in the housing) broke and we cant find a replacment for it if someone knows where to order one from thatd be amazing
Do I need to apply high temperature anti seize lubricant on the spark plug thread?
@GibbysGarage15Ай бұрын
Not required, it's preference. I usually do without.
@AmjathKhan-gt3lyАй бұрын
Thanks for the video. I never thought brake pads could cause such clanking noises. I have a weird problem, although it's similar, I'm not sure if it's the axle shaft or the brakes. Could you help? I know that my axle shafts are going bad as they created a clicking/clanking noise when I turned the wheel at slow speeds. But that's an old story. A couple of weeks ago, I had both my front and back rotors resurfaced and the brake pads changed. My brother took the car to a hill station on his vacation after that. Now, when I turn the wheel, I can hear the clicking noise, but in addition to that known problem, I can hear the clicking noise when I brake, start the car from idle, or go over a bump. What could be the reason? Did the axle shaft really go bad after his hill drive, which usually involves a lot of turns, or is it the new brake pads? Like you mentioned, it's so hard to find mechanics who are true to their heart and have the patience and knowledge to look into the issues. Thank you.
@GibbysGarage15Ай бұрын
Only way to approach this would be a process of elimination. I would take the wheel off and check for play in the brake pad like in the video. Sometimes when they clean things up really good, and use a new brake pad, it could create a gap between the pad and bracket. If that looks good, and there's no excessive play in the pad, I would go ahead and fix the axles since that needs to be done anyway. The usual approach, when trouble diagnosing, is to start where it's free/cheap first, and move up from there. I feel your pain, cars can be tricky to diagnose even for the seasoned technician. Good luck, I'd love to hear back!
@rabbitenjoyer6320Ай бұрын
I'm amazed your front rotors came off without much fuss. Mine were only 3 years old and required a couple hours of hammer blows (should have used heat in retrospect). Great video!
@GibbysGarage15Ай бұрын
That's surprising, which region are you in? I've had issues with other cars and seized rotors but I got lucky here. Thanks man!
@rabbitenjoyer6320Ай бұрын
@@GibbysGarage15 I'm in northern New England. They way over salt the roads here. Thanks again for the great vid!
@mikeTHEmanateeАй бұрын
Great video. Imo Silicon lube better for caliper pin than brake grease.
@GibbysGarage15Ай бұрын
Thanks for the recommendation, I'll try it out!
@phoenixwest602Ай бұрын
Same thing and sound on my INFINITI
@GibbysGarage15Ай бұрын
Sorry to hear! How many miles on it?
@steve8803Ай бұрын
The brakes just started clunking on my brand new vehicle with just 6000 miles on them. What could cause this?
@GibbysGarage15Ай бұрын
Does it clunk when you brake, and only again when you reverse and brake? Or every time you hit the brakes? In any event if its that new it should be under warranty.
@milanradonjic7847Ай бұрын
Yo can u do my brakes? R u in Ontario?
@GibbysGarage15Ай бұрын
I'm no mechanic unfortunately! Sorry!
@milanradonjic7847Ай бұрын
@@GibbysGarage15 ahh darn
@gcbeАй бұрын
So do I put gas when the clutch finds that biting point?
@GibbysGarage15Ай бұрын
Yes!
@shyne5637Ай бұрын
I had this same problem on my Benz installed new brake pads and when I brake the pads were moveing causeing a knock I took the pads out and took a hammer to the ends but u gota hit it on the rite spot it will expand the metal on the ears to make them a tighter fit I managed to hammer them perfect and got them to fit nice and tight but not so tight that the pads can’t slide the way they are suppose to I never had the clunk again u coulda used ur old pads u just need to know what ur doing theirs ways to fix this noise without geting the oem brake pads from experience mine was a Mercedes Benz c280 4 matic
@GibbysGarage15Ай бұрын
That's a great idea! never thought of it
@shyne563723 күн бұрын
What brand of brake pads did u use that caused the clunking and which brand did u replace them with that got rid of the clunk I replaced mine with Bosh premium pads and they were to short they made the clunking sound did u get the oem pads from Audi that fixed ur problem or did u find another brand that had a tighter fit
@GibbysGarage1523 күн бұрын
@@shyne5637 I used Centric at first, made the noise. Then I replaced them with Power Stop and it fixed the issue. Both of these were semi-metallic compounds.
@dionwolfinbarger6802 ай бұрын
Talking is allowed on KZfaq!!!
@GibbysGarage152 ай бұрын
But Mute is multi-lingual 😏
@user-cy1rd4ih3z2 ай бұрын
For my mk8 gti cs stage 2 what ngk do you want to put ?? Thank you
@prisono892 ай бұрын
Jakie to auto?
@mikepetro15592 ай бұрын
The fact that your electrical connectors came out in a matter of seconds is mind boggling. One of mine came out fine but the 2nd one is not budging. I'm going on half an hour trying to get the clip off.
@GibbysGarage152 ай бұрын
The magic of editing :) mine were VERY hard to disconnect the first time. Spray something in there, clean it up, push the connector IN, pull tab, then pull OUT with all your might, you'll hear that satisfying pop. You got this!
@orkhanasib2 ай бұрын
Did you feel that clicking noise in the steering wheel of your car?
@GibbysGarage152 ай бұрын
It can transfer through the steering wheel yes.
@orkhanasibАй бұрын
@@GibbysGarage15 My Porsche Cayenne 957 has the same problem :(
@GibbysGarage15Ай бұрын
@@orkhanasib Sorry to hear... is it OEM pads or aftermarket?
@ifGarage2 ай бұрын
How to never stall: 1. Foot down on the clutch 2. Shift into 1st 3. Hit the gas and let go of the clutch 4. Hold on tight
@GibbysGarage152 ай бұрын
That works too lol
@chifeadrian2 ай бұрын
This can be a mixing up of left and right pads right?
@GibbysGarage152 ай бұрын
I'm not so sure, I'm not certain there are cars with different left/right dimensions on the long side of the pad.
@AndrewCastorena-pg2ek2 ай бұрын
Mine does it when brake and sometimes turnin
@michaelwise69702 ай бұрын
What's the torque spec on that bolt?
@CoralSea2 ай бұрын
What capacity is your floor jack?
@GibbysGarage152 ай бұрын
2.75 ton
@brushlak81732 ай бұрын
wish i found this vid sooner lol spent 3 days under car checking bolts to realize its vertical pad movement making clunk...
@GibbysGarage152 ай бұрын
At least you found it now! Car clunks can drive anyone crazy lol
@coupdeange45672 ай бұрын
i like ur video sir ❤
@GibbysGarage152 ай бұрын
Thank you!
@TheMKTube2 ай бұрын
So it was a manufacturing defect? I’m having the same issue and the mechanic is saying it’s normal because breaks need room to move. And so paid for Lexus original breaks
@GibbysGarage152 ай бұрын
Yes it is a manufacturing defect. I would get them to fix it. They are most likely trying to brush you off, but brakes shouldn't clunk when you use them.
@TheMKTube2 ай бұрын
@@GibbysGarage15 he says the only way to fix it is to jam and rust them lol. According to him all break jobs done properly had this sound. Can’t believe this dude. Could it be malfunctioning springs that apply vertical tension to pads?
@RaisedTalent122 ай бұрын
Love this video..straight to the point no 5 minutes of bs
@ferhatovic862 ай бұрын
Would performance spark plugs not be better?
@johnle7793 ай бұрын
Manual says to criss cross the front tires when bringing it to the rear. You don't need to do this?
@GibbysGarage153 ай бұрын
Interesting... which year and model says that?
@johnle7793 ай бұрын
@@GibbysGarage15 I think it's the same for all but mine is 2021 M3 SRP. Unless your tires are directional.
@GemmaEdwards-ri3vm3 ай бұрын
Hi there, thanks for sharing this video. I recently had new front discs and pads and this knocking / clunking noise has been driving me insane. Only really noticeable when I’m braking and slowing down to a stop but it’s this exact noise. I thought maybe it could be braking hard on new brakes but I haven’t been doing this. If this is the issue, does it require new pads again or is there a work around so that it’s not a waste of new pads? Is this happening because the wrong pads have been put on by the garage? Thanks
@Samshyam1233 ай бұрын
Guys, my CRVs is not giving comfortable ride. Struts not leaking but im feeling every small bumbs on road .. should i change my structs? Its 10 years old now.
@Jahalang823 ай бұрын
Mine are the same way, they don’t leak but man can I feel everything. Been eyeballing all four in FCS on Rockauto. Originally I was going to get KYB struts and then order struts mounts from Honda but that would triple my cost.
@Samshyam1233 ай бұрын
@Jahalang82 does KYB gives better ride quality? Over oem
@Jahalang823 ай бұрын
I wouldn’t say better than OEM but probably the same. I might save up a little longer and order actual Genuine Honda loaded struts from Hondapartsnow at 150 a piece.
@alexadamsky3 ай бұрын
You just saved me about $2000 replacing the plugs and coils at my local dealership. Thank you so much!
@GibbysGarage153 ай бұрын
That's an exorbitant price for this job! You're very welcome!
@auburnboi09Ай бұрын
Please find another dealership if that's what they quoted you for what should be a $300 service. No telling what else they overcharge on.
@jeremiahbailey777711 күн бұрын
😂😂😂 oh nah 300$ MAX for this job that is attempted robbery God bless
@ernestjameslopez47033 ай бұрын
Hey bro, What year is this nissan kicks?
@senorcake54533 ай бұрын
2019
@Zakw173 ай бұрын
What did you spray in the spark plug well?
@GibbysGarage153 ай бұрын
Air duster to clean it out! So nothing falls into the combustion chamber!