I can confirm I just removed my crankshaft position sensor off my 2015 Passat TDI from the bottom with a $20 Amazon endoscope for my phone and a long ball head hex bit. I can remove the sensor in about 5 minutes without removing anything from the car. From the bottom the sensor is located right next to the oil filter housing. With an endoscope you can stick the camera in the hole, with your other hand, stick the tool in the hole. Once you seated the tool on the nut, sit down the camera, connect your ratchet and take it out. They go in much easier than you would think, They only go in one way. And then reverse the process to put it back in.
@tristanpollard12058 ай бұрын
Hey can you send a link to the endoscope?
@tristanpollard12058 ай бұрын
And how long of a ball head hex?
@wishbone20t8 ай бұрын
@@tristanpollard1205 I bought my set from harbor freight. I would say they were probably 5 to 6 in long
@wishbone20t8 ай бұрын
@@tristanpollard1205 I don't know how to get a link but search this in Google and it comes up
@wishbone20t8 ай бұрын
@@tristanpollard1205 Endoscope Camera with Light, 1920P HD Borescope with 8 Adjustable LED Lights, Endoscope with 16.4ft Semi-Rigid Snake Camera, 7.9mm
@vinceb8099 Жыл бұрын
Thanks very much, there isn't much online about the location of this. Very much appreciated.
@nathans57735 ай бұрын
Agreed. Thanks for the video
@jimmyprater754628 күн бұрын
Good video, frustrating that VW didn’t mount this on top of the engine/transmission, engineers Uhg
@manuelDureza6 ай бұрын
Thank you!
@eddydar Жыл бұрын
You dont need to do all that. You can get to it from underneath with a long ball hex.
@melancholicmuse Жыл бұрын
I'm just about to attempt this on 2.0 cr tdi (CBBB) engine, are you certain this is true? What exact length allen key to i need?
@eddydar Жыл бұрын
@@melancholicmuse yes pal. Ive done it.
@eddydar Жыл бұрын
@@melancholicmuse Its very tricky but doable helps of you got a spare sensor to hand to help co-ordinate locating hex socket
@user-ul8kt2vv7s11 ай бұрын
Do I need to drain the engine oil before taking of oil filter housing
@hardcore44764 ай бұрын
What year make and model did you do this on? Same one in the video CJAA?
@davidmessiha3988 Жыл бұрын
Thanks for the video. Have you considered going from underneath?
@corymcdowell7295 Жыл бұрын
I'm currently doing one and from underneath isn't much better. I actually used a die-grinder to take some of the side wall off for a little more access. It's a superficial mold vein, so I figured it couldn't hurt much. Idk why they set it so far back in a hole.
@danallured58064 ай бұрын
@@corymcdowell7295 i did one before and had to do that because it was in so tight that the nut rounded! what a nightmare, got anoter one in at the moment to do hence being here to see if there isan easier way!
@corymcdowell72954 ай бұрын
@@danallured5806 gotta love it right! Lol
@repairbuddy7214 Жыл бұрын
Yes it’s hard to access from there
@living4adrenaline10 ай бұрын
Hi I was replacing an oil pan on a MK6 GOLF TDI 2.0, was beating on it with a mallet relatively hard and was wondering if it could have damaged the crank position sensor because it doesn't start.
@bobirving60527 ай бұрын
Uh oh. What was it? I doubt the hammering messed it up unless you hammered the wiring. It’s a fine wire coil inside and I think it’s the heat cycles and inferior materials that cause failure.
@baula338Ай бұрын
@@bobirving6052 mine fails at high temps. how did you know this?