I usually don't comment on videos, but this was fantastic. I was quoted over $500 by an official Whirlpool repair tech to replace the ice maker in my Whirlpool WRX735SDBM00 refrigerator/freezer, and I laughed him right out of my house. With this video, an ice maker off Amazon, some good music, and a beer at my side, I was able to get it done for $100 and about an hour and a half of work. Learned something along the way too. Thank you!

You guys are awesome! Our Whirlpool French Door's icemaker crashed on October 16 and our home warranty company is still acting like it's gonna get fixed so the other day I bought my own and at first panic because I was sent a different model then I'm told the W10882923 replaced the W10377151. So I decided to follow your video and BOOM it's back and working again. Thank you so, so much. Now were gonna go comb through your other videos for more ideas.

My ice maker stopped working, Bought the replacement kit per my Refrigerator model, swapped all the cables out, removing the motor was not that hard to do for me. This video does a great job of doing a step by step on how to repair. TIP * Take pics of the old unit prior to swapping everything out so you make it the same. Plugged back in and within 15 minutes, I heard water going into the ice maker and it is now making ice, thank you so much!!

I cannot thank you enough for your tutorial. A refrigerator repairman came out to fix a drain leak and told me the ice maker was too old to repair and likely couldn’t get parts. Now, 8 months later, this nurse fixed it herself with your help! I even spliced the wires. 🙌🏻 Thanks for making this video!

Great job and thank you. ALSO note to others, I did not have to cut and splice any wires. I.E. @4:15 the ground wire you can remove the 3 bolts holding that motor in place and use a long, thin screw driver to remove and reinstall the ground. Again: thank you for this video

Thank you!!! I replaced my ice maker watching your video step by step. I am a 60 yr old women that doesn't have a handyman husband. I love him but I do all the handywork. Anyway great video and it saved me a bunch of money not having to call in outside repairman.

Thank you for the helpful video! I did notice that I could drop down a part without removing auger motor. Just removed two screws that were attached to the part with ground wire screw and there were three clips visible. just depressed clips and pulled forward and part dropped out. From there I was able to remove ground screw without cutting and was able to attach new ground wire and manually push on other ground wire before reattaching. Thanks again! I could hear the water filling and I will be nice to have ice for the first time in months!

Best in depth video I had found for this ice-maker ! I thought I had been sent the wrong part until I watched your video. You Sir are the Man ! Thanks so much !

After 3 years of buying bagged ice, I finally have a functioning ice maker. Great video. Was much easier than a thought. I just took my time and as soon as I plugged in the cord the ice maker immediately turned on and filled with water.

The video is a lifesaver, instructions were not in the box. Replacing the harness assembly would be a nightmare without the video. Well done!

Thank you so much for the great video. Could not of replaced the icemaker without this ! So appreciate your efforts to make this available for us.

Thanks to this video I was able to fix my ice maker and I had no clue how to do it before watching this video. 🙌🏽

Thanks so much for this. Ive done some appliance repairs before but this was way more complicated than I was expecting. The biggest issue I had was the first wiring connectors getting in the way of removing/reinstalling the icemaker assembly. Hope the new one lasts longer than the original one!

Thank you sir for this video! Sears wanted $250 to fix my whirlpool icemaker and I used this video to fix it myself. You rock! I'm not sure how men survived before youtube. :)

Just want to give you a shout out for this video. It helped me a ton in not only building up the confidence to do this job myself, but getting through the job in a decent amount of time. Had seen a few other videos where things were already done or they edited parts out of the vid, but you went all the way through, beginning to end. More DIY videos need to be like this

Thank you for these very helpful videos. You have helped thousands of us DIY's who are able to help lots of other people with their appliance repairs. Thank you again for taking the time to video and publish terrific technical videos to ensure things get fixed right!

Installed it as well with the help of this video. Thank you. I followed the advice of scott farley (in the comments) and was able to reconnect ground without splicing it. The one thing that was odd... My replacement didn't come with the extension shut off arm installed... I almost put it back in when I noticed it was missing. I found it in the shipping box and put it in but it seems to be not working right. It won't go down on its on.. I am not sure if it will self align itself later on but it just seems to not be working right. I put it in the fridge and heard water filling up... I will keep an eye that it indeed shuts off and doesn't keep making ice.

Thank you very much! OK, job complete. Ice maker is overflowing with ice. Mission accomplished with the help of this video. I had this same exact situation when I had to replace my ice maker. The replacement unit had an external timer wheel on it. Physically looked different. Old one was internal. Thought I had ordered the wrong one. Unit comes with 2 harnesses depending on the ice maker/fridge you have. Swapping the harness was a bit of a mission, though. Repair clinic's video sucks, just shows how to swap the entire unit out, but they left out the part with the wiring harness determination and harness change-out. The unit I had ordered was a direct replacement ice maker, but it should be noted that the unit received was a different unit with a different part number. Apparently the manufacturer, has had problems with the unit that came in the fridge when purchased so they are superceding it with PN W10882923 My original ice maker part number: W10377151 Part Number received was W10882923 Fridge Model Number: MFI2570FEZ00 Brand: Maytag

Thank you! I was able to replace my parent’s icemaker so they didn’t have to buy a new fridge!

Thanks for the video step-by-step instructions were excellent !!!

Great video! This is my first appliance repair attempt and it worked like a charm!

Thank you! Great instructions, gave me the courage to try and succeeded!

This helped me out so much, GREAT INSTRUCTIONS!! Saved me so much money paying someone else to fix it!

I inherited a whirlpool refrigerator just like this on and the icemaker didn’t work. After researching what may be the problem (water valve, located in the right back of fridge) I decided not to use the part I ordered because I didn’t want to play cat and mouse on what the problem may be. I have repaired many of the appliances in my house so I have some knowledge on how this works. There were several things that it could’ve been that made my icemaker not work so I decided to call a local repair shop to do the diagnostic. After some time he confirmed it WAS the valve, so I replaced it. It was NOT the problem as this valve had the same result ( on both I could get water from the fridge, it just wasn’t getting water to the ice maker, also every other feature, freezing, etc worked it just wasn’t getting water. Sooo, the repair man came back out and his “diagnostic” was that I needed to replace the ice maker. Bottom line after I receive the icemaker and watching your video I discovered not only did I need to replace the icemaker I needed the wiring (adapter) that the new ice maker called for. Please tell me what I need to buy, what the part number is to get the part that I need that has the correct wiring to fit w1088923!

I was able to get to the two ground wires without removing the auger motor. You can loosen the screws to provide more wiggle room but there is two screws that hold the vertical plunger switch in place and you can pull that out giving you full access to the screw that fastens the ground wire. No splicing required.

Nice video on install, found when I do these I put a little mineral oil on the side slider that goes into the grove, makes a great lubricant to help slide the unit back into position as sometimes the plastic against plastic makes it difficult to pull in and out.....

Exactly what I needed when I received the kit and needed to swap the wire harness. Thx !!!

Those plug thingies on the wire harness that seal openings through which the harness passes (and protect the harness wiring) are called grommets. 😁

Can you just splice the connector to the ice maker?

Easy to follow instructions. Thanks

Thank You for your video .I had ordered new icemaker, it showed up with 2 harness and I had no idea what to do first or how to get auger fan out, thanks!

These are great instructions. I followed them and thought I heard water filling but so far no ice. I also noticed the arm did drop down and I don't see it cycling.

Thank you very very much. I did this yesterday but the arm is stuck in up position. Any suggestions on how to make it go down? I’ve reset the whole refrigerator and did the from panel on and off. Any help is appreciated.

Just wondering why you replaced the entire harness vs just reuse the old

Very helpful video! Detailed and informative! Thank you!

Your video is really great. My problem is this. I was not able to get that icemaker out of the refrigerator. Your video said it was difficult but mine just would not budge more than about a half of an inch any suggestions?

Have not made repair yet but is is safe to assume the water needs to be shut off before beginning or does disconnecting harness from fridge automatically do that for me? Thank you.

I've noticed that you didn't reinstall the extension shut off arm (white paddle) on reassembly. Is it needed?

This morning I replaced my icemaker in my Whirlpool and the replacement didn't come with the plastic flap for the metal arm - is it really necessary to use the old one on the new?

Great video. Thanks!

I recently replaced mines but still have issues with no ice. I jumped the T and H and the unit cycles but after 24hrs still no ice. What am I missing here?

Nice video. Quick question, I am having a hard time removing the ice maker, it looks like there is a plastic cap that comes down therefore not allowing me to pull it out. Any ideas? Thank you!

Why couldn't they just send an adapter to adapt the old harness to the new? Is this not the dumbest designed obsolescence ever?

Has this ice maker been replaced by the WPW10300024 model?

The question begs to be asked, "What brain-child engineer dreamed up this convoluted assembly?" The other question, is there a way to short two terminals to run it through a cycle like other makers?

I did this exactly and it still isn't cycling. Could my new ice maker be bad?