Our fridge is still cooling but its not cooling itself anymore and getting very hot. does that mean it needs to be replaced or is there something that can be done? The fan is working so not sure what the failure is

what does 2 blinks mean? How do I find the remedy for 2 blinks?

Thank you!! Fixed the noise three days ago, couldn't have put it back together today without your assist!

I have Asko D5436 dishwasher. It gave f12 error couple times. I took out its fuses and put it back after touching with a screwdriver. Now, it is not giving any error but it is not taking any water. What do you think the problem could be? Should I replace PCB or water inlet valve? Thanks in advance

This was huge! I couldn’t re calibrate to save my life. Until he showed how to get out of diagnostic mode. Then after holding the start button I was able to run the recalibrate process. Thanks!

I'm having trouble getting the kickplate off. The screws are out, but it won't budge! I need to know specifically which direction to push or pull before I end up breaking it. I'm searching online but I can't find any data on this washer.

Can I use a sharkbite instead of a blowtorch?

Is he a B1 Droid that defected from the empire and became appliance repairman?

So lg tells me that the parts are covered but that I’ll have to pay $400-$1000 for labor. Is that valid? Like, why should I have to pay anything for a defective product? I can’t even DIY this. I hate life. I hate LG.

Where's the part where you show how to prevent it from happening in the future?

Can you get to the pump from the bottom? It almost seems like less work to pull the unit and lay it on it's side. Usually that just takes 2 screws.

Thank you so much. The step by step instructions were great.

Thank you very much for posting this! Great instructions and it was a lot easier than I had expected with your tutorial. Keep up the good work!

So what if you aren’t getting 120V to the valve ?

Key word: re-bend 👍

This is a great video. Saved me a few hundred bucks. Took my son and I an hour to do the whole thing along with the guide rollers.

Kudos for working in such a tight space and still putting your camera in a spot to get a good shot! This is a pain in the arse even without a camera in your way!!

I have question. I've done 2 dual evap compressor replacement. And I'm always getting negative readings when freon installed. Like it's showing vacuumed reading, but I've learned that's blocked sealed system. This only on 3 valve dual evaporator. Can give me some advice

What number tip do you use on the torch?

how to install D52 water dispencer

several law suits going as lg has not fix vompresdor and want 700 to replace. they spin you and refuse to honor the court orders. now its s federal ftaud case.

Great repair video! I am now a hero in our house with dry clothes. Thanks again

Super helpful video. Instead of paying $160 for a service call, then $20 for every six minutes of labor ($200/hour), and a $200 drain pump (that was out of stock anyway), I found a drain pump online for $55 and watched this video and installed it myself. Now our 15-year-old washing machine works again! Thanks!

Great vid man. Thank you

Never in my experience as a union 17 yr medical gas installer have I used any type of Flux when brazing... Flux is for soldering. Brazing is a much higher temperature. Tell me why you did?

Hi what replacement compressor for sub-zero 2711 The fridge side Thank you

Where can you get the software update? Is it available to buy?

I have the same machine as your.......I cannot find the error code list....the only one I can find is for those with the electronic display......where can I find a list of codes that displays what the error is based on the number of blinks

So I don't have the money to buy a new switch.Is there any way to shut it off

Where can I find this error codes

Reattaching the belt was a problem as I couldn't see inside the machine when I took it off. User @user-tx9zw4ld9x included a video in their comment that resolved that puzzle for me. See at 10:04 of this video: kzfaq.info/get/bejne/ipiYe5xotr3Nlmg.html My one other problem is that one of the two tabs on the control panel that get screws through them snapped off! I have glued it together. I hope it holds and I can complete the reassembly. I was able to start the dryer so I know that everything is connected so far.

Excellent repair video it made it simple to replace the idler pulley and drum rollers!!! Thank You!

Great to read the reprogramming solution shared above. GOLD! ...but note: it can be even simpler- i fixed it by cleaing the inlet valve on the dishwasher inlet hose at the tap end (low pressure being the DOCUMENTED cause) , see "unblocking the inlet hose filter" instructions 32 of manual for the asko DB1865IGXXL... or any manul for a washer or dishwasher has similar instructions . I have cleaned maby a tiny blockage from inlet hose filters over the years. But notw. It needed a few starts before it was "happy" witht the pressure. Note akso our water oressure fluctuates in Sydney a lot due to ancient street pipes bursting periodically. My washing machine detects low water pressure very sensitively despite oerfectly clean and new inket filter. So worth checking all of these things befire calling a service persin or needlessly reolacing a board.

Is there a site where I can view the error flashing codes? Can’t find mine on the washer

Getting it out of diagnostic mode how do you do that?

My back panel has plastic clips also, on the left side only, how do I get those off? PLEASE

Great video only other thing would be nice to see is the spring on/off and back on correctly. I’m forgot was flipping around a few times before settled on the spring position

My compressor has q black sticky like pad on top and on the back side. They melted eventually in the original compressor after some time and melted right away after I changed it. Is this normal? What are those black pads? Sound/vibration dampers?

Thank you very very much. I did this yesterday but the arm is stuck in up position. Any suggestions on how to make it go down? I’ve reset the whole refrigerator and did the from panel on and off. Any help is appreciated.

Anyone know what's the part number for the pulley 😅

You my friend are the real hero! Thank you!

Where do you order the piece from?

I’m so glad you made this video. It told me everything I needed to know and the confidence to attempt it. Thank you very much.

Just finished doing mine, the deice pulley would not move. Took it off cleaned it with steel wool, silicone it. since I had it apart did the rollers and vacuumed out all the lint

Awesome video, perfect clear instructions. Definitely saved me lots of money on a service call.

The best video for replacing Bosch drain pump!

Thnx for the tip 👍🏾👍🏾

Dumbass

Buddy! You are the man! Can't thank you enough for this video. It walked me right thru the process start to finish without a hitch. On behalf of everyone who's commented so far, YOU ROCK!.

I have this same one and makes like a thimping sound when spinning. What could this be?