Hugely helpful for us 460 premium owners. Thanks for making this one!
@WastingTimeInTheWoods2 жыл бұрын
Welcome!
@doironjpd11 ай бұрын
How did you cap off your electrical connectors in the wheel well? And did you have error codes showing up in your dash and info panel?
@jamesf631511 ай бұрын
@@doironjpd I didn't cap off anything. The fronts I just zip tied out of the way in the engine bay. No codes and it's been through quite a lot of mud and car washes
@doironjpd10 ай бұрын
@@jamesf6315 ok, thank you sir
@Ramiel772 ай бұрын
Had a very similar experience with my 22' 4Runner. All the kits I've installed (Billstein 6112/5100 - FOX 2.5 DSC - Dobinsons IMS) have all landed off from the expected ride heigh or lean. My 4runner isn't overly heavy (about 150 lbs added total) but I've had to always swap, adjust, add spacers, correct geometry to keep the rear axel aligned, etc etc etc, because it always lands different than expected. And also can sometimes pull to the right. Is for this same reason that I started doing my own wrenching. I couldn't imagine paying (or annoying) a shop with all of these adjustments I've had to make, to make sure it lands exactly where I want it. But I am glad I did. Because I've learned so much.
@authenthuse51652 жыл бұрын
Damn! This right here is what separates men from wannabes! Well done - this truck is now like no other in the world - this is something you built! As always I appreciate the self-deprecating humor and you sharing both the highs and lows of the job. Can't wait to see the 4Runner video.
@Maximus017762 жыл бұрын
I have the ironman cell foam stage 2 installed in my 2017 GX 460, I was planning to do it myself but l don't have an adequate place to work on, so l decided to have a professional shop to do the installation, $600 later, it was all worth it, every happy with the ironman system, now you need rock sliders, I'd recommend white knuckle off-road
@mp3moose2 жыл бұрын
Couldn't agree more with having a shop do the install after seeing Jake's video. I don't have the space or the tools on hand and was worried about the kind of issues he ran into. Love my Nitro Gas Stage 2 kit. Remember to match your spring selection with anticipated load.
@garyabiermann2 жыл бұрын
First, thank you for the content on your channel as I have nearly the same gx460 and your saved me lots of time with my build. Second, I installed a stage 3 and had every issue you did and a few more. On the sway bar I learned that a $12 2 ft alignment bar and a few jacks to apply pressure changes the game. Also you MUST put the passenger side of the bar back on first. It’s a fixed point and the kdss hydraulic ram is on the driver side. Budget a day for you UCA if you have a lot of connections on you barter cause that’s all gotta come out to get the bolt positioned on the driver side!
@WastingTimeInTheWoods2 жыл бұрын
Yeah, we did the R side first then used a jack and screw driver lever to reconnect the drivers side. I might just disassemble the whole IFS system when I do the control arms since Im doing the lower’s too. Then I can grease the bearings and get used to the layout. I rebuilt our 3rd gen 4runner completely and now I feel like I could change it’s shocks out in my sleep. I really appreciate you following along and thanks for the insight : )
@hiiiamdanny53592 жыл бұрын
Funny how a lot of your issues I just faced doing my 470. The rear is bugging me really bad also. So I am glad someone else is calling it out.
@JamesPamplinII2 жыл бұрын
I was able to get the front shocks in by dropping the skid plate and compressing the kdss cylinder with a floor jack. Didn’t even have to unbolt the kdss or sway bar. Was effortless once I saw a random KZfaq comment mentioning how to do it. Spent two hours trying to figure it out first. Seems to not be well documented anywhere but it’s so much better than fighting it with a 2x4.
@WastingTimeInTheWoods2 жыл бұрын
That does sound better. Might try that sometime. How did that work of the R side with the fixed link?
@JamesPamplinII2 жыл бұрын
@@WastingTimeInTheWoods I was able to jack under the opposite side wheel and it dropped down, just couldn’t do that on the side with kdss because it fights you too hard.
@balaramg2 жыл бұрын
Sorry to hear that you had to go through all the trouble. I have installed ironman with UCA on my gx460. I didn't even need the spacers and nothing collided. Luckily I had the non airbag version which made the install very easy. I had to install the spacers later to give more room for droop at the rear. I have been to Black Bear pass, engineer pass, hells gate and merus. It's keeping up everything.
@WastingTimeInTheWoods2 жыл бұрын
Sounds like a sweet rig. Wasn’t that bad on my install, I just bitch and moan for extra entertainment value ; )
@balaramg2 жыл бұрын
@@WastingTimeInTheWoods that's the reason i like your channel. Humor with knowledge. I recently did the black bear pass and hell Revenge. Lexus is awesome engineering Marvel
@knaudi862 жыл бұрын
Amazing video. It convinced me to hire this out when the time comes!
@stephenmorgan65782 жыл бұрын
I did what was then the Stage 3 Kit with UCA’s on my non-bagged 460. I disconnected my sway bars also, but I have 3 floor jacks so I used a combination of those and ratchet straps to get the sway bars back in place and bolted up front and rear. Did the whole thing myself. If I had a helper I might have been able to use the 2x4 trick to get the coil overs in, which caused much swearing on my part in any case. I though the UCAs were going to be a pain, but they weren’t bad actually. My alignment with the lift and new UCAs was not far off. The alignment shop only had to make one small camber adjustment and I was good to go. I experienced the same with crazy height on install, but a quick drive and it settled right down. I have probably the same rear springs as you, performance 2”, and with any load they settled down. With the family of 4 and all of our camping gear loaded up, she sits really nice and rides like a Caddy.
@WastingTimeInTheWoods2 жыл бұрын
Yeah, I should remeasure now that its been about 6 months since the install. Still looks like a stink bug though.
@tommyholland3664 Жыл бұрын
The reason for extra lift in rear is because of the coil conversion. Ironmans bottom perch adds extra lift that non airbag GXs wouldnt have. I believe Metal Techs bottom perch is the only one that doesnt add extra lift.
@rc7074 Жыл бұрын
Comedy gold, Keep learning from yours and others mistakes and you'll be an ace mechanic if you live long enough. I learned mine from age 13 on and now I'll tackle just about anything. Plus you'll have an awesome set of tools.
@bartman1857 Жыл бұрын
llp0pm
@cardp172 жыл бұрын
great video once again!! extremely helpful, honest opinions always appreciated. poor chewy!!
@WastingTimeInTheWoods2 жыл бұрын
He’s a tough bastard. 30 minutes later he was jumping into my truck uninvited like always : )
@CliffCakes2 жыл бұрын
Man I've been there. I think we all have. On my install I ended up loosening the front lower control arms knowing I'm going to get an alignment anyway. That made it much easier for sure. I put the truck on the ground and tightened everything up however now I have an assortment of warning lights on and my steering wheel is way off. Hopeful a proper alignment and a google search with fix my issues. Take care!
@WastingTimeInTheWoods2 жыл бұрын
Good luck! Dont forget to do a zero point calibration. Took care of the Christmas tree lights for me.
@candidcapture2 жыл бұрын
Great presentation!!! Thank you!
@BillReals Жыл бұрын
IDK know why you don't have way more subs, your content is really well done.
@LifeEnTierra Жыл бұрын
Love the videos man keep them coming!!! “And don’t disconnect the sway bars” 🤣
@DDG58 Жыл бұрын
Nice job
@kirkgoree13082 жыл бұрын
You'll have 2 Yarises (Yari?) by the time you've built both the 4R and GX...Great videos!
@WastingTimeInTheWoods2 жыл бұрын
Thanks!
@FissionChips19832 жыл бұрын
The salt on that "let's get started" at 1:56 could be tasted from here. Lol.
@familygromscarsfun38967 ай бұрын
Once we THOROUGHLY stripped the the bolt..... 😂😂😂😂
@chriseppley82722 жыл бұрын
Great content as usual!
@robbergstrom9432 жыл бұрын
Kudos for doing the install and sorry to see all the drama. Looks like you have a “good” excuse for that swing out rear bumper, bump up to 33s, and an extended range gas tank. Maybe I’ll leave our rear on air springs and just upgrade the rear shocks as adjusting air rise height with washers take 2 minutes.
@WastingTimeInTheWoods2 жыл бұрын
Most of the trouble was just my inexperience. Getting more comfortable being covered in grease now : )
@benjaminharvey2229 Жыл бұрын
Link for the service manual....if it's available online?
@doironjpd11 ай бұрын
Just did this install this weekend. Removing the sway bad was very VERY tempting. Had some issues but everything came together alright. Though I'm still throwing codes to check air suspension after removing the fuses and wondering how best to seal off the electrical connectors
@doironjpd11 ай бұрын
Sway *bar*
@WastingTimeInTheWoods11 ай бұрын
Awesome. Congrats! Did you do a zero point calibration? That might fix it. I never had any issues. I just used electrical tape and wrapped them up and zip tied them so that the connectors would gather water (pointing down so they would drain any water). Curios, did Ironman ever update the kits or did you have to cut the bolts for the spring perches?
@doironjpd10 ай бұрын
@@WastingTimeInTheWoods yep, had to trim the bolts. It was an older kit though. I've had it sitting around for over a year. Hopefully they've updated them since. Your video was very helpful, appreciate the upload! My next move is to mess with the height sensor and see if that helps correct the error
@godspeed27893 ай бұрын
Silly question about the front. Why not use a spring compressor. Or put the wheels on and lower it so it compresses the spring and then connect the sway bar?
@WastingTimeInTheWoods2 ай бұрын
Probably could of, but I hate those things. Since doing this I’ve seen a few demos of how it can be done by jacking up one side. Ive got a set of ucas and lcas sitting on my shelf so I’ll probably find out here shortly.
@olsonj2 жыл бұрын
Just found your content and learning what i can from you... We are debating getting a 460 or a 4runner or a grand cherokee to use for light trail riding & exploring here in Oregon so we can take my mom with us to get her out of the house after we recently lost my dad. So I guess I'm curious on your take, if you have a moment, on those vehicles new and what your thoughts are on loading 3 dogs (2 german shepherds and a lab) and 3 adults in with some light gear for day trip exploring (13 hr drive days round trip). Do you think either one is better then the other? It's also will be my wife's daily driver and she's 5' nothin... So I don't want to get something big for her then she won't want to drive it. Anyways, hope you see this and give some input. Love learning from your content and its super entertaining.
@WastingTimeInTheWoods2 жыл бұрын
Thanks buddy! So sorry to hear about your dad. All three are pretty big vehicles but none are too hard to get into if you don’t lift it (& u don’t need to) Im biased. We own a 4runner and GX and I would never buy anything but a Toyota product for resale and reliability reasons. The one thing I’ll say about our GX for dogs is that the rear air conditioner is amazing for them. They pant and drool a whole lot less when they jump back in the car since they have their own vents all the way in the back. Its only on premium models though. Good luck and let me know where you land!
@Gx460guy8 ай бұрын
Doing a 3” lift this weekend thanks for the video. What did you set the rear bag delete spacers at?
@WastingTimeInTheWoods8 ай бұрын
I set them to the minimum height then raised the L side 1/2" (to compensate for the lean). I got +3.375" on both sides after settling with 3" 'stock load' springs.
@ebaad264 ай бұрын
Hi. Nice videos and good job done. Quick question: did you get “ check air suspension” error in the dash. I have the same setup installed on my gx 460 model 2010 and 2 things that i m not happy 1st is obviously a “ check air suspension “ error on the dashboard which is permenant How do i remove it ? 2nd from the front the vehicle is much lower than from the rear. Assume its the design of this vehicle Can you pls advise to make my day
@WastingTimeInTheWoods4 ай бұрын
Not sure what I did to get so lucky but I never got an error and never added washers to the sensors or anything. I did a zero-point calibration (paper clip method) right after the lift, and all the warning lights went away and never came back. I left my compressor and valve block in and just removed the lines. Hope you can sort it out. Warning light would drive me crazy!
@WhatD4FCK Жыл бұрын
Are you thinking in getting the dr kdss clamps and sway bar ends adapters? Also I saw you only install the kdss spacer in the rear is there any reason you didn’t in the front ?
@WastingTimeInTheWoods Жыл бұрын
Yeah, I was actually thinking of reaching out to Dr. KDSS to try those when I swap all the control arms. Looks like a good product.
@titanslug5 ай бұрын
I believe you do not need the front KDSS drop spacers IF you use the Dr KDSS front end adapters. I will mention that if you install the front end adapters, you won’t have a hard time getting the sway bar back on like this guy did. Go check out the Dr KDSS video where he installs the front end adapters on a lifted 4Runner, he has no issues getting the sway bar back on.
@aiden83175 ай бұрын
Hi was your driver and passenger side coilovers different? It seems that they shipped me 4runner coilovers which says passenger , driver on them! also wondering if they are same as GX460 coilovers.
@WastingTimeInTheWoods5 ай бұрын
I think they are just set up differently for lean but not sure. 5th gen 4runner and gx have the same struts so don’t sweat that.
@10TPOPR Жыл бұрын
What height lift kit did you order? 3" front and rear? 2.5" front, 2" rear? Etc.
@The24solo2 жыл бұрын
Nicely done! This is the Autozone guy. Did your rear-end ever settle?
@WastingTimeInTheWoods2 жыл бұрын
Hey, buddy! Nope. Still perked up.
@cybrah Жыл бұрын
Great video! Are you running 275/70/17?
@544shannon2 жыл бұрын
Are your rear shock perches adjusted all the way down? I don't recall you mentioning anything about that in your video? FYI - for whatever reasons due to suspension geometry and "magic" whatever distance your adjust on the perch is DOUBLED in ride height. I have been running the same suspension for almost 3 years now on my GX470. In that time, I have had to make several adjustments to my spring choices due to unplanned modifications. Initially, I went with the front performance springs and a year later got a steel front bumper..... so I upgraded to the HD springs. The rears were probably the same option as yours, up to 660lbs. However, over the years I have accumulated so much gear that the rear began to sag. Instead of going to the rear HD spring, because I thought it would be over sprung and the ride would be too stiff, I opted for those spring perch adjusters to get the extra lift I needed to level out my truck. When I am unloaded, it sits like yours with a noticeable rake. When it's fully loaded, it's perfectly level. I have learned to live with it and it's a good compromise. I also thought about raising the front coil overs a tad as well. Have you thought about that? I have been watching your build progression over the past year or so and since you are "budget minded" I would say stick with what you have. Like me, I purchased so many things I never thought I'd buy and all that weight really impacted the ride height of the truck. You might end up buying a rear tire carrier or rear bumper like you mentioned. That alone will probably make a substantial height difference in the rear with all of your additional gear loaded in the truck. I am also on the fence about buying a steel rear bumper with swing outs and again, I will probably end up purchasing HD springs and have to adjust the perches to a lower setting. I know you didn't know about the spring options when you ordered your kit, but perhaps in light of saving some time and cash.... in the long run I think you'll be okay. I guess worst case scenario, if you do go to the 1.5" springs, keep your current springs just in case.
@WastingTimeInTheWoods Жыл бұрын
Great insights. I agree. Leaning towards not messing with it and maybe adjust the front up a half inch. We’re renting a travel trailer to go to Sedona in October and I think I’ll appreciate the extra sprung in the rear. Thanks for the tips. Sounds like you’ve been around the block a couple times : )
@chopperpl2 жыл бұрын
Hi, thanks for the video What offset and tire size were you running that it was rubbing so much? Have you fixed this issue?
@JerryFrancel2 жыл бұрын
What did you do about the rear bolts being to short?
@WastingTimeInTheWoods2 жыл бұрын
Cut 1/4” off the ones that are too long.
@thorsky2754 Жыл бұрын
Had same dang bolt issue with the Metal tech kit, bolt was too long.