Need a fancy new tool? Lang Wheel Stud Restoration Kit: amzn.to/3OdVpH9 OTC Ball Joint Press: amzn.to/3xLEOFf Lisle Pickle Fork Set: amzn.to/3mEUp2K
@mikehartmann51872 жыл бұрын
Seriously, what I could use is a recommendation for a ‘good’ ( I know, I know) spring compressor kit. I drove the Chevy to the levy and now I need new front shocks.
@WatchWesWork2 жыл бұрын
@@mikehartmann5187 No such thing. Find a shop with a Branick or OTC spring compressor and have them swapped out.
@burtbacarach50342 жыл бұрын
@@mikehartmann5187 Coulda been worse,coulda drove a Ford to the Fjord.
@harrywalker9682 жыл бұрын
wes wes,, lez swing a 10 lb hammer..this dodge will send you broke,,''no,im not working that rusty p o s , get it out my shop,,now.''.. i think ive said before, i have an f250 s/duty, 02. with a 4.2tdi, mwm sprint. german..no glow plugs, no computer. its a diesel. 3 valve, 3'' system. mine has 700nm. about 560ft lb,ish.. gets 12.5 lt 100.. ford, didnt like selling them.. being in bed with IH..heaps in brazil,,africa..canadia, had some..4 cyl version as well. next was common rail,2008, never seen any.. cant beat i 6..
@harrywalker9682 жыл бұрын
on car brake lathe. had the 5 stud bronco done 15 yrs ago, still good..rang now for it to be done on 8 stud 75 , 250.. nope.. now i have to pull front apart to replace them, fk this country..aus..everything to damn hard..
@thomasdavis42532 жыл бұрын
These old trucks are real work horses. I inherited my grandpa's 1994 2500 12v when he passed away in 2005. He used to keep one of those disposable tear off calendars struck to the dash. The last one is still there, stuck on the last month he drove it before he passed away..... 17 years. That truck took me and my dumb young adult choices all over this country and always managed to bring me home safe. Sometimes she was limping, but she always got me home... or somewhere safe. All the while chugging a cheerful tune, sounding like she was happy to be there, and glad to help. Now days, she is a little worse for wear. The dash is cracked, and there is more primer and light surface rust than the original Champaign paint left, but she still sings that happy song, and even though it would be cheaper to take the motorcycle or the new Chevy to work (especially with current fuel prices), I prefer to use the old 12v.... that way, I can ride with all my memories...
@HANKTHEDANKEST Жыл бұрын
And the nice thing about the old 12v is that long after the body rots away, you can pull that fine old 6BT and run a great big sawmill or something out in the bush. Hell, you could just stick it on a stand and run it for yuks--I bet your granddad would get a kick out of that, I know I sure would.
@jkgkjgkijk Жыл бұрын
Write a book! You are a skillful writer. I enjoyed reading your comment.
@odiarroyo6144 Жыл бұрын
@@jkgkjgkijk I did so too Even a had a traer in my eyes knowing that I have one of these treasures ..I.. 94 1500 5.2 5 speed I got it with 82 Now has 87 thousand in the taco..
@azteacher26 Жыл бұрын
I think I've got something in my eye.
@LitRomney-vb6pz Жыл бұрын
Wholesome comment
@oldhouseredux77332 жыл бұрын
I think we all need to take a minute to honor the old codger that took METICULOUS care of this awesome truck for all these years before the new owner bought it!! Wow Wes - what a fun job to get!!
@Luckingsworth2 жыл бұрын
Its a 95 my dude. Not a 50+ year old car.
@MobertRiller2 жыл бұрын
It’s 27 year old car, there are very few 1995 cars of any type that still look ok
@plepgeat2 жыл бұрын
Yeah, @@Luckingsworth , no one's EVER seen a 27-year-old pickup that's in bad shape.
@JesseLemus12 жыл бұрын
I agree. I live in Texas where previously to recent times we haven’t had a lick of salt on our roads and it’s still a rare sight to see a truck in such good condition. Especially a “work” truck.
@justnsaliga85182 жыл бұрын
@@Luckingsworth only ever seen brand new 27 year old Work trucks. Never seen one with any rust on them out of the thousands i've seen...... lmao bruh. just look at watch wes work. more than half the stuff he makes videos on is a vast majority of anything older than 2008 in terms of work trucks pickups diesels of any brand. some hold up better than others due to location but they all endup like most of the trucks he typically makes videos on.
@countryboy445552 жыл бұрын
The movie Twister made the Dodge Ram even cooler to me as a kid. Love these 2nd gens. I don’t live in the rust belt so I get to see all these rigs almost daily. Thanks for the content Wes!
@01SilveradoLT2 жыл бұрын
That’s a great truck right there. I’d take that over a new one. Love the engine tone on those. What a find.
@jbrennan1232 жыл бұрын
Diagnosis....."It's a dodge." Seriously though...to see a dodge pickup of that era that hasn't literally disintegrated from rust is pretty amazing. Also seeing that the door panels and the dashboard haven't shattered into a million pieces is also pretty amazing. Every pickup from that era with at least some sort of accumulated milage all have mechanical issues. I'd take these issues over a disintegrating pickup any day. Thanks for the video Wes.
@tammylott9212 жыл бұрын
THE SAME EXACT RAM USED IN THE MOVIE ( TWISTER )
@petero26932 жыл бұрын
Not in San jose..all rust free..but sun damaged.. we got Kaiser Fraser pickups used by lawn service red..
@TheKillerMarine2 жыл бұрын
My 01 with 250,000 miles isn't rusted and the original dash and it lived in Michigan, you have to take care of them
@stephengordon5762 жыл бұрын
Laughs maniacally because it’s true
@loginavoidence122 жыл бұрын
coworker bought one of these 15 years ago, and his words were "the truck is a pile of shit, but you buy it for the Cummins"
@jabbasan122 жыл бұрын
Love the fact that when Wes finds something other than what he was asked to fix, he addresses it. I see too many mechanics just fix what they were asked to, when it would be ultimately cheaper for the customer to fix it when you are in there. Nicely done Sir!
@Robrt322 жыл бұрын
I bet he contacts the owner to make sure he can bill for it. I would be surprised if he didn’t because it’s good business. You can’t do free work to much and stay in business
@Le_Comte_de_Monte_Felin2 жыл бұрын
Book time says 8 hours to open hood.
@mdouglaswray2 жыл бұрын
I've found it best to give all mechanics an upper-cost limit and give them the calls on replacing parts. Then there's no consuming his time chasing you around asking. Good mechanics can always give estimates with monetary caveats for each extra replaced part and the likelihood of it needing to be changed. Also, being cheap on that upper limit guarantees you'll hit it faster next time around. My favorite is timing belts/chains. The time and labor to replace one while you're in that area is nothing and helps avoid the worst disaster a cam-driven valvetrain can experience. Wes, your meticulous inspection is so gratifying - finding that zip tie under the valve cover seal was a testament to your eagle eye to use a Puddinism.
@OpaqueWindow2 жыл бұрын
You must not get yelled at by people, I gave up long ago on doing unnecessary work the customer didn't ask for.
@Robrt322 жыл бұрын
@@OpaqueWindow that’s why I said I bet he ask first. I know I will get pissed if something is fixed and it’s costing more because I could a felt like it was a problem I could have put off until I have more money. Right or wrong it’s still my decision if I can spend that money right now. I also wouldn’t expect it done for free.
@jonarment12296 ай бұрын
The 1994 Dodge Ram was the first modern truck. That model changed trucks from a utilitarian tool, to something even people in the suburbs wanted to drive. What a beautiful specimen! Thanks for showing it to us...
@karencary33122 жыл бұрын
I was watching Diesel Creek today, also. Two things you 2 have in common: 1) You ALWAYS make things INTERESTING, and 2) You both would be NOWHERE without your good WIVES and your HAMMERS! Love ya!!!
@warrenmichael9182 жыл бұрын
yes but Eva is bat crap crazy!!! LOL Matt needs to get her in more videos , shes a hoot!
@trevorvanbremen47182 жыл бұрын
Be careful to never confuse the wife and the hammer.. It will ALWAYS end in pain!
@The513Warning2 жыл бұрын
I've been going through a lot, Wes, and I gotta say, your videos always cheer me up. I recently got accepted into the plumbing union and started my apprenticeship last week. I've been pretty excited over it but when I finally broke the news to the few people in my life, they acted uninterested and bored. Definitely stung a bit and it makes me feel like I'm the only person who takes genuine interest in other peoples' success and hobbies. Or because I'm quiet and patient, everyone is always emotionally dumping on me or looking for advice. Anyway, rant aside, just know I appreciate whatever videos you put out and I enjoy them to the fullest the way they are. And whenever I have asked for your advice on car stuff, it's always appreciated and accepted. Thank ya, Wes.
@WatchWesWork2 жыл бұрын
Congratulations! Plumbing is a good profession.
@The513Warning2 жыл бұрын
@@WatchWesWork I appreciate that! I'm enjoying it so far. I'm hoping it'll all be worth it in the end. In Ohio, it takes 5 years to become a journeyman.
@waiting4aliens2 жыл бұрын
@@WatchWesWork The society which scorns excellence in plumbing because plumbing is a humble activity and tolerates shoddiness in philosophy because it is an exalted activity will have neither good plumbing nor good philosophy. Neither its pipes nor its theories will hold water. John W.Gardner. Humble plumbers I have know who continued on and received a Masters Licenses in Plumbing, HVAC, and Gas fitting never had to worry about their daily bread.
@ferrumignis2 жыл бұрын
If it's anything like the UK then good plumbers, electricians etc. are always in high demand and they earn a pretty good living.
@The513Warning2 жыл бұрын
@@ferrumignis Plumbers and sparkies are definitely in high demand right now. Even though I'm going through the union and education is top notch, I still have some of my own doubts that I'll be a good plumber. I got interviewed in front of the entire union board and got selected out of a very big class this year but I still have huge doubt and some imposter syndrome going on.
@bananabikerider2 жыл бұрын
I appreciate the fresh take on 90's dodge trucks; at least speaking of them in a positive light in the intro. Weird to think about but dodge was a real underdog in the truck market since... well forever until the second gen came into the market in 94'. I try to think about that whenever I find any short comings on my 97' Cummins truck. Chrysler didn't have the kind of investment capital to put into these as much as Ford/Gm did due to sheer volume/production #'s. The introduction of the second gen, in my opinion, was the hail Mary that saved Chrysler's participation in the US truck market
@Mun562032 жыл бұрын
From what I understand the 89-93 cummins trucks was what saved the truck division for them, then the 2nd gens was there first body redesign since like the 70's. And the 2nd gen carried the success of the 1st gens. Both are great trucks, but a lot was used hard and put away wet
@BudMasta2 жыл бұрын
@@Mun56203 They also fell apart daily and the glass transmissions would only continue.
@bluegrassman30402 жыл бұрын
@@Mun56203 the first gen had a frame that was not heavy enough in the front end for the Cummins engine. Those had the same frames from the 1970s.
@92powerdiesel612 жыл бұрын
@@bluegrassman3040 They aren't bad if you add the steering brace or convert to crossover steering. All of those trucks (72'-93') had issues with the steering box area.
@doubleq1223 Жыл бұрын
Wow, this truck is immaculate. It’s amazing how well an old vehicle can hold up when the owner takes care of it.
@mrdrchad61102 жыл бұрын
This is one if the nicest looking 5.9 cummins shipping crates I have seen.
@johnclamshellsp19692 жыл бұрын
To Wes. The remaining "sloppy steering" is caused by the steering shaft rag joint. Speedway engineering makes a solid joint for this. I had mg 99 Ram 2500 and same thing. All new front end parts and still a slight slop. Yep yep
@kbr18872 жыл бұрын
I posted lower down, but in mine it wasn't the rag joint itself, but the cinch bolt in the lower u-joint of the steering column shaft that holds it on to the input shaft on the steering box. It was just slightly loose, which caused fairly significant play.
@blackdogexcavator212 жыл бұрын
I've owned a 93, 95, 01, and now an 09, all with the Cummins. I also have an 89 that is 100% stock. Never a problem from any of the engines and believe it or not, not one transmission issue (yet). I have experienced most of the other "normal" Dodge issues along the way. I think it's safe to say that Cummins engines saved Dodge trucks.
@rawr519192 жыл бұрын
The engines last a million+ miles yet the bodies just rot around them if you look at them the wrong way
@hithere73822 жыл бұрын
@@rawr51919 They last a little longer down in redneckland.
@weshawkins71652 жыл бұрын
Use to be a saying that with the Cummins engine you had a 500,000 mile engine in a 100,000 mile truck. Don’t know about that, I have a 2000 with a 120,000 on and still perfect.
@hithere73822 жыл бұрын
@@weshawkins7165 In my region if they're worked routinely one can get around 300,000 miles out of the body but it's expensive to do it. This implies it gets nowhere near the beach or salty roads ever at all.
@weshawkins71652 жыл бұрын
@@hithere7382 Mine started out in Iowa but within six months was a California trunk. I don’t drive it in snow or salt. As an old Dodge dealer tech I do all my own work.
@deercreekmechanical2 жыл бұрын
The cam bolts for the caster adjustment from the factory “tuck the axle into the truck”. If you adjust them to “rock the axle” as far out as possible it is a massive improvement. A friend that worked at a dealer when these first came out did that even when new. I did the same to my 2003 and I also added a steering box brace. That also made the steering much more positive.
@JOHNSUE284 ай бұрын
Excellent. Positive caster is a good thing!
@user-rk1bf4eh2pАй бұрын
What a great design, can't beat those older trucks
@pipefitter17282 жыл бұрын
I know it’s a lot of work to film and edit the videos but I love these hour plus long videos! Thank you for all the extra work it takes to allow us to see what you do so well! Like you and many comments that truck is in unbelievable good shape! Too bad you don’t get more like that to work on.
@richardblinks2 жыл бұрын
So agree! Wanted to give it double likes!
@LloydAlexander58 Жыл бұрын
So much better than TV! Thanks a lot for your effort in making these videos
@justintothetruth11 ай бұрын
One of or the most important comments that should be read and said by everyone 😊
@malware_in_tn90082 жыл бұрын
Wes, production quality continues to improve with no loss of interesting content. Three thumbs up!
@ericfuentes71632 жыл бұрын
Too afraid to ask where's the third thumb...
@johnyb988410 ай бұрын
I’m 65. We called them ‘wind wings’ instead of flipper windows. My mom used to keep her cigarette by the open wind wing between puffs and you could see the smoke get pulled outside. She died at 60 from lung cancer in 1990, so there’s a lesson for someone there (hopefully my son who smokes). If you opened the wind wing a little more you got a strong gush of air on yourself on a hot day. I love this truck. Great video Wes. First time watching your channel
@MayaPosch2 жыл бұрын
Can't believe I saw a mint '95 Dodge Ram on this channel. Getting all the 90s nostalgic vibes too. Total unicorn indeed. I'm pretty sure I just dreamed this video and none of this ever really happened :(
@joejakubec97082 жыл бұрын
My 88-year-old uncle has the same truck, different color here in Arizona with 50,000 miles. Absolutely mint, never seen rain or of course snow. As a former Chicagoan car guy, Arizona spoiled me. Also, Wes has the best channel and content. For the grown people. Takes me back to Illinois without having to be there.
@DanEBoyd2 жыл бұрын
I'm in Ohio, and the Chicago cars I've seen here were all really beat up, in addition to the rust. Our cars rust pretty bad too.
@luvr3812 жыл бұрын
Odd, I really thought Dodges were made out of rust at the factory.
@REWYRED2 жыл бұрын
Gotta rust proof the hell out of them and keep em "wet".
@danpaul94232 жыл бұрын
My 2022 Ram 4500 already has some rust on her.
@REWYRED2 жыл бұрын
@@danpaul9423 What really?? Shit I have a 2019 and got the factory rustproofing AND take it to a local shop annually..... No rust yet. Had a 2000 for 17 years that started getting bad around the floor pan and in the corners.
@jordangochnour73562 жыл бұрын
3rd gen beds are for sure
@sjfk13062 жыл бұрын
What about GMs and fords? Lmfao.
@MortskeRepair2 жыл бұрын
Twister was the movie that set those Dodges off for me!
@kaitheramptruckman75392 жыл бұрын
Sure it wasn’t fast and furious?
@WatchWesWork2 жыл бұрын
Did it make you want a fleet of blacked out Caravans?
@MortskeRepair2 жыл бұрын
@@WatchWesWork And a dually squarebody suburban!
@brucehobbs17342 жыл бұрын
First, nice work on such a nice rig! Second, it’s great to see an owner let you do the work that needs to be done and stay ahead of it turning into what you usually work on. 😁
@alc8182 жыл бұрын
Hey Wes If you want to get the Dodge Ram to stop wandering down the road (it's not the steering box) you will need to repair / replace the steering column. The bushing inside the column fails and leaves a lot of slop...
@oscarwalton11882 жыл бұрын
A death wobble brace is a must other than that they were actually really good trucks
@jasonmorgan37092 жыл бұрын
Need to upgrade the “Y” tie rod and drag link to the “T” style upgrade. That’s helps a ton.
@alc8182 жыл бұрын
I think you will find that the he problem is with the steering shaft coupler inside the steering column... And while you are in there, you might consider replacing the clock spring and your cruise control will start working again... Ask me how I know...
@alc8182 жыл бұрын
The bushing in the steering shaft of my 94 Dodge Ram 2500 allowed the steering wheel to rotate about 20 degrees before turning the steering box. Pretty simple to test if you use a pair of vise grips to secure the steering box from turning then hop inside and turn the wheel... You must lock the steering box because the resistance inside the damaged bushing will make it seem like everything is OK... An ideal job for a good assistant... lol
@bigjay67432 жыл бұрын
@@alc818 Same Lol took me forever to find the problem in my 98 ask ME how I know 🤜💥🤛
@brianwalk1082 жыл бұрын
that twin ram intake helps get air to the rear cylinders, the intake manifold didnt do a great job of distributing it evenly from the factory. It also helped conditions with the rear cylinder temperature being a lot hotter than the rest. if a cylinder went out on one of these, it was always that rear one.
@badazz29692 жыл бұрын
Just had an 04 Cummins 2500 roll through my shop with 42k original miles all stock lived it's whole life in a garage in southern Illinois it was a time machine for me only being 22
@henryjensen27412 жыл бұрын
Dude. The opening was awesome. This channel is coming so far. I have loved watching you learn your way through every conundrum that rolls through your door. Your an inspiration brother.
@divadyrdnal2 жыл бұрын
I bush hogged an ancient barbed wire fence that was “mostly” buried in a heavy grown over ditch bank…took me hours to uncoil (using a torch, wire cutters and grinder) all of that barbed wire from the “stump jumper”… wire was probably 2-3 inches thick in spots. Got a new respect for the guys that cut ditch banks everyday!
@pgmurray762 жыл бұрын
I guess it was too tight to the drum/spindle for small bolt cutters. Ok, torches are faster too. Actually, that stuff gets stiff when curled and shortened. Sorry you had a rotten time. I only get some stories from my cool public works neighbor across the street. He just upgraded to an X-mark for his personal use and a 2022 Ford F-150 TT V6 from an ancient Toro and a 2004 Toyota Tacoma with rusted out, but replaced rear brakes. His yard looks so good with all this eye candy now. Son of a farmer married to a daughter of a farmer.
@18robsmith2 жыл бұрын
That was a pleasant change for you - no rust, and ran as sweet as a nut. You deserve at least one of those every week.
@jackiemay94712 жыл бұрын
no sound effects with brake clean no big nasty great video nice truck keep up the good work Wes
@jeepanimal29432 жыл бұрын
As a Dodge owner, Dodge, not Ram, of a slightly younger vintage, mine's an '04, I will say, finding a Dodge in that shape in my neighborhood, is impossible. South Western Ontario Canada, where we "season" our roads quite liberally. And being on a main road from major population, to another major population, my strip of asphalt gets "Extra Sauce." A Unicorn? Yes, almost a "Holy Grail" of pickups in general. Had it been a manual, there would need to be an accompanying shrine to the third pedal and "that extra steel lever looking thing." But in all honesty, OMG! that truck is freakin' clean!!!!! Nice work Wes, keep 'em coming.......
@garyhawthorne45992 жыл бұрын
Thanks for the video, I have a 1996 Dodge Ram 4X4 that was converted to a mega cab 4 door, when it was pretty new. It only had 120,000 miles on it when I got it. It had been parked for 10 years. It now has about 157,000, I changed the interior to cloth, not a fan of leather (cold in winter and hot in summer) We did brake and axle seals ect. The killer D pin ect. I use it usually for towing. almost every time I drive it someone will come up and try to buy it, I always tell them I need it to launch my boat. My daily is a 2003 Dodge Ram 3500 four door short bed, 6 speed with over 300,000 miles and runs like new. 20 mpg regular use and 16 towing over 10,000 lbs. The 1996 gets about 16 mpg and about 12 towing
@frankm85332 жыл бұрын
Pretty nice rides. My buddy has 06 Mega cab Cummins dually 6spd he bought new has 186k starting to rust Pretty good but he just took it across country and back no issues but the rust is taking it away he's slowly buying all the body parts for a major over haul this winter I think
@willb30182 жыл бұрын
That sending unit swap is a piece of cake, setting aside the dropping the tank part. 😉 Great video with diagnostics and multiple fixes. Thanks.
@gtb81.2 жыл бұрын
i wonder if you could pull the actual resistance unit off and replace it, they look the same
@terryrogers10252 жыл бұрын
I like it young man. I’ve had 2 Dodge trucks with Cummins in them, good engines, but, it all comes down to maintenance, and that’s no matter what it is, No maintenance = junk. That was a beautiful truck sir, had to be nice to work on. Thanks for the ride along.
@tonyprior808 ай бұрын
I absolutely love this channel. This project is very complex. I admire your dedication and attention to detail, not to mention your ability to problem solve.. I look forward to seeing how this finishes up.
@99andrianmonk2 жыл бұрын
Nice job, Wes. Well done. The truck is beautiful. The owner is one lucky person to find it. An aberration here in Illinois. Max doesn't say a lot but speaks volumes. His face expressions say it all.
@shawndyer81402 жыл бұрын
this truck never saw winter road salt for sure. truck was parked on a paved drive.
@Deezle_Gaming2 жыл бұрын
One thing that helps the steering on these 2nd gens is a steering box brace. It puts another bearing on the outside of the pitman arm on the sector shaft. Without it, you can watch the box/shaft wiggle side to side when you steer in place.
@LawF2502 жыл бұрын
I replaced my steering box with a large over sided sector shaft. Doesn't require the brace and drives with 37s down the freeway and offroad with no problems at all and steers so easy like it has hydro assist!
@wheelieking712 жыл бұрын
Strongly disagree with the BS brace gimmick. They do not work. I have installed several (by request). There is always a significant amount of run-out in the silly "stub-nut" thingy that fits in the bearing. (Yes I have measured this. Yes, I know how to measure this (I am a machinist)). This would cause binding, IF those bearings were tight enough to prevent it. They are not. Not to mention, non sealed bearings. And those two small 3/8" bolts do not provide enough clamping force to stop the bearing from walking under load. The stupid things are a temporary bandaid at best. It is not the box that moves (I have measured this as well). It is the sector-shaft flexing. As LawF250 suggests, a box with a larger sector-shaft is the correct fix. Especially with over-sized or wider than stock tires.
@Deezle_Gaming2 жыл бұрын
@@wheelieking71 My truck came with the brace on it and it drives nice. My buddy replaced everything on his front end, including the steering box it and still wandered. He put the brace on and it went away. I agree a steering box with a bigger sector shaft is a better fix, it's also pushing $1k.
@Inline6Guy2 жыл бұрын
Those are actually terrible. The frame needs to flex and when you put a brace on the front of it like that the gearbox absorbs the flex. No bueno
@helivesonforever2 жыл бұрын
@@LawF250 what brand box did you use?
@sabrekat79042 жыл бұрын
Nice to see that you actually get a nice vehicle to work on once in a while and really good to see that, for once, most of the truck actually leaves with the truck and not, as seems more usual, swept up and leaves in the dumpster.
@curban05202 жыл бұрын
When I had a '95 ram, i found much improvement in steering after replacing the steering gear and a special kit that puts a special pitman arm nut that rode in a big bearing supported by frame structure.
@OtherWorldExplorers2 жыл бұрын
I really like that beginning. That was really good I can appreciate how long it took to make.
@antonoudenhoven75732 жыл бұрын
Good to see a well maintained vehicle so now and then. Love the fixing vids,nothing wrong whit diagnostic ones,but these i like more. Also great to see the owner is fine by spending some money on it
@FenrirFabrication2 жыл бұрын
They really are great trucks when taken care of. i did a g56 swap in mine. 742k miles and still going strong and gets over 22 mpg compared to my durtamaxes 12.... though with the 60-gallon tank im running it now costs $300+ to fill up....
@tomkruger34962 жыл бұрын
I remember when those came out too. For me that body style was the beginning of Ram trucks. As a kid I didn't even know they made them before that.
@jayramsey49532 жыл бұрын
Thank you guys for the awesome content. I say you guys because I know a business like yours is a family effort. I really like the way you go about fixing all of these vehicles. You are very methodical, professional and clean. I’m always impressed with the work that you do. Wes, I wish I lived near your shops to have my truck worked on by you. It is a 2002 Ford F-250 XLT. It is a very clean truck with low miles. It needs a new bearing and outer axle seal on the driver’s side. It also needs a rear differential flush and fluid change. I have a new Rear differential cover. It is a good one that allows the fluid to circulate. I also have an electric diff locker from a 2008-2015 F-250 which can be retrofitted to work on my 2002 F-250. My truck is 100% rust free. I’m from Tucson, Arizona where there is no such thing as rain or humidity. Maybe a road trip? Thank you again for your videos and content.
@andyfixedit18052 жыл бұрын
I hadn't ever seen a different indicator fluid for sparkless ignition vehicles. Found some available locally, but I'm gonna need to be convinced that it's not just different color before I open my wallet. Thanks for the info, keep up the great work!
@lloydmarche30582 жыл бұрын
Beautiful old truck. Sometimes I miss my Cummins but the then remember changing out water pumps, seals , steering box , and front end parts more often than you would think . Had the death wobble several times. The good feeling goes away fast.
@Charles-oe4kj9 ай бұрын
I love those generation of dodge but the one before it is my absolute favorite
@Mikelp732 жыл бұрын
This year is hands down my favorite truck ever made.
@wonjat52 жыл бұрын
Nice job Wes, the new owner is off to a good start. Agree with your views on valve adjustment, for mine, just a light drag.
@danieloutloud91512 жыл бұрын
So very nice to see you work on a vehicle that was in such great shape . Could actually see clearly what you were repairing and you weren't having to construct all sorts of methods to pry apart corroded parts . A touch of "normal" repairs is relaxing to watch .
@deejay49222 жыл бұрын
Had a 93 Dodge Cummins D250 2WD. Gave it to a cousin in '03 w/ 225K miles. He kept it a decade as an off road truck. He sold it to his propane guy a decade later for $700. It's still running almost 30 years later. These old Cummins are awesome motors. Great video.
@blackhatch462 жыл бұрын
Decent looking shipping crate!
@matyasxfulop2 жыл бұрын
I love watching these. Would love to know the story behind this truck and how it was kept so clean. Don't let whistlindiesel get a hold of it.
@volvo092 жыл бұрын
Up next "bought some old man's pride and joy! Let's jump it! Ends in fire!!!"
@Joshua-jc3oo10 ай бұрын
It's relaxing 😎😌
@garybrugone433 Жыл бұрын
A truck with no rust. You must have been in heaven. Great Video. Stay blessed.
@peterperigrino14032 жыл бұрын
Wes very fine work sir..... I own a 97 p-pump 3500 4x4...drw....it needs a ton of work....it was real nice to hear that Cummins Purr.....ain't no other....thanks for the great video...
@nicholasviney59752 жыл бұрын
First time I've seen a truck leave the shop at the same weight it came in at, most leave half their structure behind as rust chunks on the floor. Nice work Wes
@Daxun1552 жыл бұрын
Glad your back
@jimburgess92052 жыл бұрын
I always watch you and Rainman Ray for your diagnostic expertise. You’re both very good at your job. Thank you for your hard work.
@benjaminbear15122 жыл бұрын
Awesome video! I just finished restoring a 1987 Mazda RX-7 Turbo. I worked on it for about a year. I use a cool prgram on my computer called Automotive Wolf car maintenance software to track all the parts and expenses so I know exactly what I have invested in it. I have about 6K in it now and plan to sell it for 12K after paint. Thanks for the great video
@weshawkins71652 жыл бұрын
Great video Wes. Your videos are always like it is. Your living right, those unit bearings NEVER come out that easy. I’ve got a 2000 Dodge 2500 CTD since 2002. 120,000 miles on it, love it. I put a Fleece cooling system bypass on it, and a PacBrake exhaust brake system on it, a FASS lift pump and just put a manual locking front hub kit on it. No DEF and no cats, My forever truck. I would like to find another one, 97 or older so I can avoid the smog line here in Commiefornia. Then install a 24 valve with the P- pump conversion kit. Interesting, the ball joints press into the knuckle on the 98’s and older. Om my 2000 they press into the ears on the axle tubes.
@HUBBABUBBADOOPYDOOP2 жыл бұрын
Thank you for the video, Wes!
@roamin_ronin Жыл бұрын
I love the attention to the little things: When reinstalling the valve covers you wiped the tops down to get your fingerprints at least slightly less greasy. All in a greasy engine bay, that no one is gonna see. Keep up the good work!
@daveneil3963 Жыл бұрын
That was a clean 95 Dodge! The new owner sure knew the right person to take it to!! I had a 2000 Dodge diesel and I loved that truck. I put in the Edge module so it had 330HP and 670FP of torque, I got 17-19 mpg city driving and several times I got 27 mpg on the hiway!! But it did wander and no one could fix it. Also the trans would would go out of overdrive with a Big bang when under a load so I had it rebuild and it did the same thing which was a common problem. It finally broke and left us stranded! Went to a dealership and they finally got a factory remanufactured Trans and I never had that problem again, but it was 5 grand! If I'd lived close to Wes and he had the time he could have fixed all of that and I wouldn't have had to put up with all that for several years. Thanks for another great video, I'm going to watch some more of your videos right now.
@ScottDLR2 жыл бұрын
That is indeed a super nice rig! I have a bit of a Unicorn or holy grail Dodge truck of my own. 2003, 5.9 (pre-emissions), NV5600, Manual XFER case quad cab with 135K. It looks about the same as that one paint-wise. I want a new one but this one is too good to give up. BTW, yes, the volt meter thing is normal. As far as the loose steering, if the gear hasn't been replaced, it needs it. No adjustment of the secotr will correct for a worn box. I learned this one the hard way. Red Head makes a great rebuilt gear. Yes on the constant tension clamps and if you use OEM hoses, they come with them.
@andrewhansen4179 Жыл бұрын
I replaced my 99 original steering box with a Redhead. The first one they sent me had trashed splines, sent back. Second Redhead came and was sloppy after install, a real surprise. Took that one out and got a PSC box that was better, but still came with slop in the gearing. I remember a day when the truck was new and the steering was super crisp. Front end is all brand new but these steering boxes seem to be the weak link in precise steering. Grrrrrrrrrrrrrrrrrrrrrr.
@slade93722 жыл бұрын
Whenever I see a unicorn like one of these I always feel like they should be in a museum or something. It's kind of a shame to imagine it lasting this long only to potentially have something happen to it. Hope that viewer looks after it well!
@Watchyn_Yarwood2 жыл бұрын
Those 8 point sockets have been very handy for me! When I bought them, I had no idea I would ever use them except on antique farm equipment, but that was not the case.
@NickManCuso5911 ай бұрын
Best looking truck dodge ever made !
@interdiction22 жыл бұрын
Just saw you using the suction pump and over here in the UK I've just bought a 1.5litre version of the same pump (already got two of the smaller ones like yours) and it's really handy. Differs in having a much longer tube plus a stop tap arrangement on the end to stop dribbles whilst transferring liquids. Also has a handle to go around the larger body. Just letting you know as we are usually behind you guys so no doubt they're available on your side of the pond. Enjoyed the video too. 😁👍 P.S. AvE says "Cut towards your chum, not your thumb".
@zinntv493111 ай бұрын
id rather cut off my thumb than my chum!
@pinwizz692 жыл бұрын
WOW, incredible I actually got 1st like and 1st comment on one of Master Mechanic Wes's vids which is pretty much impossible given how fascinating and popular his vids are. Vocational school, we don't need no stinking Vocational school. We'll just watch an episode of Watch Wes Work Y'all. It's always nice to wake up to on a Sunday morning and see he's posted a new one.
@WatchWesWork2 жыл бұрын
You're the man!
@mummabear012 жыл бұрын
@@WatchWesWork I wasn't that on the ball but I'm "like" number 101. I could have done bettter but I was watching my Sunday Mustie1 video. Love your videos, Wes.
@pinwizz692 жыл бұрын
@@mummabear01 I was watching Mustie1's vid to when the notification bell message came up so I immediately switched over. I'll go back after this to finish Darren's. Then Diesel Creek and some others.
@DanEBoyd2 жыл бұрын
@@pinwizz69 Ol2Stroker is another good one.
@pinwizz692 жыл бұрын
@@WatchWesWork. Thanks Wes. As someone with vocational school diplomas on small engines (2years) Motorcycle repair vocational school and a as a Veteran Coast Guard Aviation Machinist Mate A school then asca Flight Mechanic on Grumman HU16e Albatross seaplanes Pratt and Whitney R1820 radial engines (you'd love changing spark plugs on those, only 16 of them and some are definitely struggle bus fun) and C school on Sikorski HH52a Seaguard helos with General Electric T58 turbo shaft engines I can definitely appreciate how absolutely professional you are as a Mechanic. You're definitely a galaxy better that over 99% of mechanics I've delt with. Especially how honest you are about your abilities and how well you explain what you're doing as you work. I'm dead serious about how awesome a vocational school instructor you'd be if you wanted to be. I have no doubt your son will be as well when he grows up.
@bladerunner62824 ай бұрын
bought a new stripped down, bread-truck white 1/2 ton manual one of these with the 318 standard cab, AC, hand-cranked roll down windows and rubber floor mats in 2001 for 18 grand. it's not got about 92,000 miles on it and still running great. it's been dinged to death but no major crashes or dents in the body or bed. ...love it! it would still look good if i ever washed it., haha best manual transmission and clutch i've ever owned, and i've got a 2007 aston martin and porche cayman with manuals that suffer in comparison.
@AntonioClaudioMichael Жыл бұрын
Lots of routin Maintenance ON this old Rig That extra deep trans Pan Is beautifully made going to be a brand new Truck when your done with all the repairs and Maintenance on this old rig good video as always @Watch Wes Work
@Deezle_Gaming2 жыл бұрын
Pretty clean for a rust belt truck. If you think that sending unit is a pain, I have a 98 12 valve, the only sending unit still made for the half year unicorn is at Geno's Garage and it's nearly $400. I have a universal ultrasonic sending unit on the way, can't wait to see how it works.
@wes11bravo2 жыл бұрын
Wow - is that how it calculates fuel tank volume instead of a float and a potentiometer (or differential comparator ckt or whatever)? Does it pulse a soundwave and do some kind of wizardry that converts to a voltage to signal the gauge?
@rawr519192 жыл бұрын
@@wes11bravo Never heard of such wizardry like that before for a sending unit, technology
@Deezle_Gaming2 жыл бұрын
@@wes11bravo It mounts to the bottom of the tank on the outside and uses ultrasonic waves to detect the fluid level. It has a little control box that you use to calibrate it to your fuel gauge. Other companies also offer ones that use a standard SAE hole pattern where you cut a hole in the tank and put it on top, I wanted to refrain from cutting any holes in my tank. I was nervous about the sensor on the bottom of the tank being exposed when the truck is used offroad, but I figure if I mount it at the rear of the tank it's right near the axle and very difficult to drag over something.
@wackowacko89312 жыл бұрын
FYI, there is a difference between "new" and "rebuilt or replacement" steering gears. Rebuilt steering gears usually only replace seals, but they don't really replace any internal parts. The main issue is the center shaft. This shaft wears the most at the center when the truck is driving straight ahead since that is the position that the steering wheel is pointed most of the time. The shaft then wears out in the middle but not at the ends. This over time causes the truck to wander when driving straight, and there is no adjustment that will fix it. This is why you need to have a new steering gear or one that is completely rebuilt by a shop that knows how to do it. Also, be careful with the sector shaft setscrew - if you over tighten this it can cause the steering gear to lock up while driving. It is usually just best to leave this alone if at all possible. They make a steering gear support brace that can help a bit with a wandering issue, you can get from most Cummins aftermarket shops. The frame tends to flex where the steering gear is bolted to it, the brace helps with that. If you have a front end that is slap worn out, you can crank in the most negative caster that the front end will accept and this will help it to track straight a little better until the front end can be rebuilt.
@kellykonoske912 жыл бұрын
Visited my daughter in the UP of Michigan, and every Dodge I saw over a few years old was literally disapearing before my eyes from fust! this one is amazing looking. Todd the retired trucker.
@Omc-Steelbone2 жыл бұрын
I like how you talk and film your episodes. I just get a cold snack or two and forget my daily nightmares and zone out.
@wreckerjonny61442 жыл бұрын
Wouldn't be a Cummins or a dodge if it didn't leak something. That's miiiiiiiiinnnnnnnnnntttttt 👌as an old wise man said
@number1youtuber5612 жыл бұрын
This means a lot to me since my dad stole mine, glad to see someone else caring about them as much as I do
@danl.r23792 жыл бұрын
I remember seeing this body style on the movie Twister. What a beautiful truck.
@gagechapin10002 жыл бұрын
looks like it was bought in Midlothian Texas
@dwaneholiday40432 жыл бұрын
You didn't do the Andrew Camerata radio intall.....rip off dash pad to get to wires.chainsaw to make raido hole larger..( looks factory)
@jamesanderson21762 жыл бұрын
I test drove one of the first Dodge Cummins models, still in the old, square body style. It felt like I was driving a steel-wheeled tractor down a Chicago expressway. NOTHING gave when you hit a bump.
@1320fastback2 жыл бұрын
Mine feels like driving a 30 year old dump truck. After completely redoing the interior including a complete seat rebuild it now feels like driving a 30 year old dump truck.
@Mr.NiceGuy802 жыл бұрын
Can't forget about twister. The movie that brought the new ram trucks to the world. Good times.
@markstock35102 жыл бұрын
Well I never, a Dodge radio install without a chainsaw.
@utubesmitty68522 жыл бұрын
Hi Wes, thanks for the vids. Is it possible that since that transmission was modified for heavy towing (deep magnesium pan, extra fluid capacity, who knows what else...), it does not reach normal operating temps when running with no extra load - so it may shift like its cold and the temp gauge may not register? Perhaps the pickup doesn't get deep enough in the modified pan?
@edwardcostello88332 жыл бұрын
I started my career at Dodge as a technician in 1994 and yes they were very popular and fun to work on
@anthonydefreitas60062 жыл бұрын
Even Max can't resist popping bubble wrap.
@av8tore712 жыл бұрын
This was the day and age when Chrysler was AMERICAN! I worked at the Belvidere, IL Assembly plant during the summer when I was in Law School and when the Dynasty & New Yorkers were being built now FIAT owned them and Chrysler is going down his. Should have stayed American!!
@aserta2 жыл бұрын
Don't get it twisted, it was US' citizens who elected the stooges who made it extremely easy for traitorous CEOs to move US' industrial might to other countries. Be it sold or outright outsourced. It was one of the biggest post war mistakes, to allow megacorporations to exist unchecked. The Bernard London, planned obsolescence went full steam ahead and mediocrity and "buying themselves out of obsolescence" became the major MO. Look at what happened to Master Lock. A well established company, with good bones, bought and then stripped to pieces, turning it into a joke, literally and figuratively. Many other examples exist, Chrysler and other car brands included. It's utterly fascinating to me how decades upon decades, ya'll (to borrow that wordage from you) still don't get that it starts in the gov and it ends in shame. You can't elect traitors and expect the country to remain whole.
@mph58962 жыл бұрын
What is left of Chrysler will be out of business in the next 10 or so years. Jeep name and Ram will live on. Everything else will die.
@av8tore712 жыл бұрын
@@mph5896 maybe. It'll be like AMC or who ever had the Jeep name before Chrysler had it. Plymouth is gone now. The Caravans are no longer being made and that's what gave Chrysler its name. My entire family worked at the Belvidere IL Assembly plant so it's been a staple in my family for over 51 years
@mdariff8392 жыл бұрын
You know what West,if i live anywhere near you, you are the only mechanic i know..
@michaelbenoit2482 жыл бұрын
The nice thing about working & owning a high miles taken care of truck is that for the most part anything you go to fix has probably at one point been replaced. The disadvantage of buying a clean low miles clean truck is that a lot of the stuff on it hasn’t been done at all or it’s barely driving w 30yr old grease in places.
@Thedavidsavage2 жыл бұрын
It's very rewarding to see the pride you take in your craft. All those special things different compounds and different torque methods. Add up to a job well done. Have an ice-cream you earned it.
@timbow50 Жыл бұрын
I had a truck like this from 96’ to 88’. I never had any major issues at all. Sold it at 269k miles. It was probably 90% clean.
@johnelliott73752 жыл бұрын
I bought one in 1995 when I First seen it on the car lot! 6 foot bed single cab 318/ 4wd and a 5 speed manual transmission. I paid 27 k out the door title, tax , registration, and a full tank of gas. The sales manager I went to school with threw in life time Pennsylvania state inspection. Great truck and thank for sharing. I will watch it and pass it on for you Wes! Great evening to you and your family. Pet the old puppy for me would ya! Thanks.
@victorh8863 Жыл бұрын
RAM will always be king
@Rift452 жыл бұрын
Thank you for giving these trucks some love. My first truck was a ‘99 Cummins. Great looking, nice driving truck. Far from perfect but it was a breath of fresh air
@buckroger5850 Жыл бұрын
My 94 2wd Dodge cummins had that wandering problem until I swap it over to rack n pinion. I also installed a zf6 6 speed manual out of 08 f450 super duty. 👌
@AllisChalmersMN2 жыл бұрын
My dad had a 97 Ram 2500 gas engine truck. He used it for his construction business. It had the back seat but no rear doors. I remember riding in there for thousands of miles.
@zmotorsports622 жыл бұрын
Love seeing unicorns Wes. i can't speak for others but I would rather see unicorns being worked on vs. beat up old run down vehicles that you can tell the owners don't care about. I have been fortunate that over the years I have weeeded out the clients that don't take care of their stuff and now have a good selection of well maintained vehicles that run through my shop owned by people who care about them and don't cringe about spending a little bit of money to keep them pristine and in proper running condition. Also, a little tip when doing front axle work on solid axles (Mopar) when you have to pull axle shafts is to cut a pole jack down so that when you pull an axle shaft on one side you can place the cut down pole jack under one side and slightly raise it enough to prevent the differential fluid from the center housing from running out the seal and into the axle tube. Makes for a very clean job without having any cleanup of fluid afterwards plus makes the outer axle housing end more solid when working so it doesn't bounce from the coil springs. Another great video Wes. Keep em' coming, especially those "unicorns". Mike
@marklarson94362 жыл бұрын
I bought a brand new Ram in 2001, 2011, and in my current truck in 2021. 10 years and 200k plus miles on the first two. Love my new one. Some folks must have had bad luck I guess. I'll likely buy a 4th in 2031 if I'm not dead.