Water Surface - TOUCHDESIGNER TUTORIAL #1 - Français & English Subtitles

Рет қаралды 4,092

2 ай бұрын

Welcome to this first tutorial! I hope my explanations are clear enough, don't hesitate to give me any advice!
As I say in the video, this network is a base and is destined to be improved, or even used in other networks.
Share with me your creations, your modifications, ideas, etc. :)
You can contact me directly on Instagram if you want!
/ sarv.live
Have a good day ♥

Пікірлер: 26

@marienara 6 күн бұрын

Ravie d'avoir trouvé des tutos ENFIN en français ! Merci beaucoup !!!! 🥰

@LukeHildreth 16 күн бұрын

love this method!

@markus_knoedel 2 ай бұрын

Very nice. At 20:30 you can shuffle inside of the topto-CHOP = output as single channel set. But this is some good advice on water surfaces. I tried water for a long time now, but I never came up with those ideas. Thank you so much

@sarv.live7 2 ай бұрын

Hi Markus ! Didn't know for the ToptoChop "Ouput as single channel set" parameter ! Thank you for this ! And thank you for this comment ! :)

@joelfelipe953 Ай бұрын

trop bien !!!

@vinzuel402 2 ай бұрын

oui trop bien je vais pouvoir regarde ce tuto , mis en playlist :)

@sarv.live7 2 ай бұрын

N'hésite pas à faire un retour sur ce que tu as aimé et les améliorations possibles ;)

@WinonaVrignaud 2 ай бұрын

thank you! super helpfull!!!!

@sarv.live7 2 ай бұрын

♥

@Yohannjaffres 2 ай бұрын

Merci pour le tuto ! 🙏🏻👌🏻

@sarv.live7 2 ай бұрын

Avec plaisir ! 😌

@DanielSteenhoff Ай бұрын

Nice work!

@sarv.live7 Ай бұрын

Thank you

@nato_slmn 2 ай бұрын

thank uuuuuuu

@sarv.live7 2 ай бұрын

You're welcome

@hinduspl 2 ай бұрын

💥👍

@sarv.live7 2 ай бұрын

@riflex9424 Ай бұрын

Les français sont là !!

@sarv.live7 Ай бұрын

Oui Monsieur !!!

@NicolaWidgeon 2 ай бұрын

hank you for your video, but when exporting the movie to Mp4 video format, the water flow runs very fast. Can you take some time to guide me on which tool to use to adjust the flow speed to run as fast or slow as desired? (Because I'm new to self-study, I don't really understand). Thanks a lot. Hope you have time to make each instructional video for those who don't know anything about Touchdesiger.

@sarv.live7 2 ай бұрын

Hi ! I'm actually not at home so I will answer to you soon ! But for now, check if the fps rate at the bottom left corner of TouchDesigner is the same as set in the "movie file out" node. Try as well to change the phase in the Ramp TOP, try absTime.seconds*0.1 or *0.01

@sarv.live7 2 ай бұрын

Dm me on Instagram or mail if it doesn't work !

@NicolaWidgeon 2 ай бұрын

@@sarv.live7 Thank you very much, I did it by increasing it to 0.01. Hope you have plenty of time to compile a series of basic instructions on Chop for beginners.